JBLメーカーHTI88の使用説明書/サービス説明書
ページ先へ移動 of 12
HTI88 HOME THEA TER IN-W ALL SERIES OWNER’S GUIDE ® HTI88 OM 4/19/05 4:43 PM Page 3.
INCLUDED THANK Y OU FOR CHOOSING JBL For more than 50 years, JBL has been involved in every aspect of music and film r ecording and reproduction, from live performances to monitoring the recordings you play in your home, car or office.
3 SPEAKER PLACEMENT Low-frequency sounds are normally omnidirectional, meaning the listener can’t tell where they are generated from. However , frequencies between 75Hz and 150Hz can be local- ized, especially at higher vol- ume levels.
Speakers and electronics have corresponding (+) and (–) termi- nals. Most manufacturers of speakers and electronics, including JBL, use red to denote the (+) terminal and black for the (–) terminal.
5 amplifier or your main receiver/ amplifier to power the HTI88, select one of the two con- nection methods that follow . Connection Method #1 Use this method when you are using the HTI88 with your main receiver/amplifier .
6 the high-passed signal to the speaker -level outputs for connection to the satellite speakers. NOTE: When using Connection Method #1 with only one HTI88, the shorting straps must be removed.
7 Phillips-head #2 screwdriver Measuring tape Utility knife Pencil Carpenter’ s level Awl T ools Needed The JBL HTI Series in-wall speakers were designed to be easily installed. However , if you are unsure of your ability to properly install these loud - speakers, please contact your dealer or a qualified installer .
8 HTI88 EXISTING CONSTRUCTION The grille is packed separately from the speaker . If at some later date you wish to remove the grille from the speaker , to avoid scratching the grille or baffle you may unfold a paper clip, insert the straight end through one of the holes in the grille, and gently pull up.
NEW CONSTRUCTION Y ou may either purchase the optional HTI88 back box kit, or you may install the speaker after the wallboard has been installed by following the i nstructions for existing construction on page 8. INSTRUCTIONS FOR INST ALLING THE HTI88 USING THE HTI88BB BACK BOX KIT The HTI88BB enclosure (“back box”) is optional.
10 P AINTING THE SPEAKER FRAME AND GRILLE JBL HTI Series loudspeakers can be painted to match any décor . If you wish to change their color , the satin finish on the grille and frame will function as a primer coat. Before painting, install the plastic paint shield securely into the recess in the baffle.
TROUBLESHOOTING I f there is no sound from any of the speakers: • Check that receiver/amplifier is on and a source is playing. • Check all wires and con nec tio ns between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other .
DESIGN GOAL: Combine the superior performance of traditional JBL loudspeakers with the convenience of in-wall installation. WOOFER TYPE: Polymer-coated aluminum cone with rubber surround CROSSOVER NET.
デバイスJBL HTI88の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
JBL HTI88をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJBL HTI88の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JBL HTI88の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JBL HTI88で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JBL HTI88を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJBL HTI88の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JBL HTI88に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJBL HTI88デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。