JBL ProfessionalメーカーBASSQの使用説明書/サービス説明書
ページ先へ移動 of 12
JBL ® PERFORMANCE ™ SERIES OWNER’S GUIDE JBL BASS Q ™ AUT OMA TIC ROOM-MODE- CORRECTION PROCESSOR ® JBLP2338 BassQ 5/8/08 4:54 PM Page 1.
3 Important Safety Instructions 4 Introduction and Features 4 Included Accessories 5 Operation and Controls 8 Connecting Y our JBL Performance Series System 9 Installing the JBL BassQ Processor 10 Cal.
3 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
4 INTRODUCTION AND FEA TURES INTRODUCTION Congratulations on your purchase of this Performance ™ Series JBL BassQ ™ processor! Y ou have purchased a product that embodies the best of what JBL ® engineers have learned about the emo tional power of audio reproduction in more than fifty years of preeminence in the field.
5 1. Power Switch Pushing this button is all that is required to turn on the unit if it is not part of a JBL Performance Series system and the Main Power Switch A is in the On position.
6 11. Main Power Switch Place this switch in the On position at all times during normal use. 12. Power T rigger Input Jack When using the JBL BassQ processor in a JBL Performance Series system with the A V1 digital surround processor , you will need to use the trigger cable set included with the A V1.
7 REMOTE CONTROL BA TTERY INST ALLA TION The remote control requires one CR2032 battery . The battery should be replaced as needed. When battery power is low , the remote control enters a low-voltage con- dition, preventing it from operating the JBL BassQ unit.
8 GENERAL INFORMA TION A JBL Performance Series system installation incorporates one preamp/ processor (A V1 or AV2), one power amplifier (A VA7) – in addition to the amplifier(s) used to power one or more subwoofers – and one JBL BassQ processor .
9 PHYSICAL INST ALLA TION Installation of the JBL BassQ unit is a straightforward process. IMPORT ANT : The JBL BassQ unit must be installed following the directions below . Always put amplifiers on the bottom of a stack. Heavy equipment should not be supported solely by the front- mounting locations.
10 Once you have connected the sub- woofer input into the JBL BassQ unit and connected the outputs from the unit to all subwoofers in the system, you will need to run the BassQ test to finalize the room calibration and correction. Before Y ou Begin It is very important that all subwoofers are on and installed before you run the BassQ process.
Problem: The JBL BassQ unit does not turn on. Neither the red nor blue indicator lights are on. Make sure the JBL BassQ processor is plugged in, and verify that there is the proper voltage at the wall outlet. Make sure the Main Power Switch A on the rear panel is in the On position.
Features, specifications and appearance are subject to change without notice. JBL is a trademark of Harman International Industries, Incorporated, registered in the United States and/or other countries. Performance, JBL BassQ and Pro Sound Comes Home are trademarks of Harman International Industries, Incorporated.
デバイスJBL Professional BASSQの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
JBL Professional BASSQをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJBL Professional BASSQの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JBL Professional BASSQの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JBL Professional BASSQで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JBL Professional BASSQを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJBL Professional BASSQの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JBL Professional BASSQに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJBL Professional BASSQデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。