JBLメーカーSYNTHESIS SDP-40の使用説明書/サービス説明書
ページ先へ移動 of 171
SYNTHESIS SDP-40 DIGIT AL SURR OUND PR OCESSOR/CONTR OLLER USER GUIDE.
12. Use only with the car t, stand, tripod, bracket, or table specified b y the manufacturer , or sold with the apparatus. When a ca rt is used, use caution when moving the car t/apparatus combination to av oid injur y from tip-over . IMPORT ANT SAFETY INSTRUCTIONS 1.
JBL SIS Products Gr oup 8500 Balboa Boule vard Nor thr idge, CA 91329 250 Cross ways P ar k Dr ive W oodbur y , NY 11797 800-336-4JBL Pa rt No . 070-14991 | Rev 2 | 06/03 DOCUMENT A TION CONVENTIONS This document contains general safety , installation, and operating instructions for the SDP-40 Digital Surround Processor/ Cont roller .
Introduction JBL ii Section 1: Getting Started About the SDP-40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Highlights Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Remote Control Battery Installation .
Introduction SDP-40 iii Section 3: SETUP (continued) TRIGGER SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-48 LOCK OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50 Section 4: AUDIO CONTROLS AUDIO CONTROLS .
Introduction JBL iv ENGLISH IMPORT ANT SAFETY INSTRUCTIONS Save these instructions f or later use. •F ollow all instructions and warnings marked on the unit. • Always use with the correct line v oltage. Refer to the manufacturer’ s operating instructions fo r the power requirements.
Introduction SDP-40 v ESP AÑOL INSTRUCCIONES IMPORT ANTES DE SEGURIDAD Guarde esta instrucciones para uso posterior. •U tilice siempre el voltaje correcto. Diríjase a las instrucciones de operación del fabricante para obtener las especificaciones de potencia.
Introduction JBL vi IT ALIANO IMPORT ANTI NORME DI SICUREZZA Conservare le presenti norme per l’utilizzo futuro. • Osservare tutte le istruzioni e le avvertenze apposte sull’unità. • Utilizzare esclusivamente con la tensione di rete corretta.
Introduction SDP-40 vii D ANSK VIGTIG INFORMA TION OM SIKKERHED Gem denne vejledning til senere brug. •F øl g alle anvisninger og advarsler på apparatet. • Apparatet skal altid tilsluttes den korrekte spænding. Der henvises til brugsanvisningen, der indeholder specifikationer for strø mforsyning.
Introduction JBL viii NORSK VIKTIG INFORMASJON OM SIKKERHET Ta va re på denne veiledningen for senere bruk. •F øl g alle anvisningene og advarslene som er angitt på apparatet. • Apparatet skal alltid anv endes med korrekt spenning. Produktbeskrivelsen inneholder spesifikasjoner for strø mkrav .
Introduction SDP-40 ix Unpacking and Inspection After unpacking the unit, save all packing materials in case the unit ever needs to be shipped. Thoroughly inspect the modules and packing materials for signs of damage. Report any damage to the carrier at once; report equipment malfunction to the dealer .
1 Getting Started About the SDP-40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Highlights • Product Registration Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Do • Do Not Remote Control Batter y Installation .
Getting Started JBL 1-2 ABOUT THE SDP-40 Thank you for purchasing the SDP-40 Digital Controller , a reference- quality , 12-channel audio and video control center with independent zone monitoring to provide control of input source selection in three zones at the same time.
Getting Started SDP-40 1-3 Complementing its pristine audio performance, the SDP-40 includes two broadcast-quality video switchers. An ultra-wide bandwidth component video switcher accepts analog component or RGB video signals, while a composite and S-video switcher accepts high-quality NTSC, P AL, or SECAM video signals.
Getting Started JBL 1-4 INST ALLA TION CONSIDERA TIONS The SDP-40 requires special care during installation to ensure optimal performance. Pay particular attention to the bulleted items that begin below and to other precautions that appear throughout this user guide.
Getting Started SDP-40 1-5 REMOTE CONTROL BA TTERY INST ALLA TION The remote control requires two AA batteries that should be replaced as needed. It is recommended to use Alkaline batteries, which last longer without leaking.
2 Basic Operation Front Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Rear Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Remote Control Over view . . . . . . . . . . . . .
Basic Operation JBL 2-2 FRONT P ANEL OVERVIEW 1 2 4 5 7 6 8 10 12 9 11 3 Red LED Amber LED IR Receiver Blue LED.
Receives infrared commands from the SDP-40 remote control. There are three LEDs located in this area as shown below . An amber LED blinks when a remote control command is received.
above appears on the on-screen and front panel displays. These graphs illustrate the position at which the current Zone 2 or Record Zone volume level falls within the –80 to +12dB volume range. 3. Release the selected Zone 2 or Record Zone input selection button when Zone 2 or Record Zone volume level has been set.
Basic Operation SDP-40 2-5 8. Main Zone Off Button Deactivates the Main Zone. 9. Zone 2 Input Selection Buttons Selects the input in Zone 2. When an input is selected, an amber LED lights on the corresponding input selection button.
Basic Operation JBL 2-6 8 3 15 5 13 14 12 1 11 6 10 16 9 2 4 7.
Basic Operation SDP-40 2-7 When a 5.1-channel analog source is present in the Main Zone and the INPUT SETUP menu ZONE2 IN or RECORD IN param- eter is set to DMIX, only the (L) and (R) input signals are sent to the Zone 2 or Record Zone audio output connectors.
Basic Operation JBL 2-8 Rear Panel Overview (continued from page 2-7) 10. Main Zone Video Output Connectors Provide video output in the Main Zone. Two composite video connectors, two S-video connectors, and one component video connector (BNC) are available.
Basic Operation SDP-40 2-9 REMOTE CONTROL OVERVIEW The SDP-40 remote control provides full operation of the SDP-40, performing commands such as menu navigation that are not available from the front panel. The command matrix that begins on page 2-14 indicates the commands remote control buttons perform when each command bank is activated.
Basic Operation JBL 2-10 Button Navigation Command(s) MAIN MENU The MAIN MENU represents the beginning of the menu structure. It can be used to open the three main menu branches: MODE ADJUST, AUDIO CONTROLS, and SETUP.
Basic Operation SDP-40 2-11 MENU ITEM SELECTION The remote control arrow buttons must be used to select menu items. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CO.
Basic Operation JBL 2-12 To select a parameter setting with a horizontal graph: 1. When the horizontal graph appears, press the and arrow buttons to increase and decrease the setting in designated increments. The current setting appears at the right of the parameter name on the on-screen and front panel displays.
Basic Operation SDP-40 2-13 DVD-1 DVD -2 L D TV CD T APE TU NER MENU PVR SAT FP BLUE OSD VCR AUX GAME MAIN SHIFT STA T 7 / 5 2 CH MUTE MUSIC ZONE REC L I G H T MODE VOL Shift Record Zone Main Zone Button Zone 2 1 2 3 4 1 Activates and deactivates standby mode when the SDP-40 is powered on with the rear panel power switch.
Basic Operation JBL 2-14 Button Main Zone Zone 2 Record Zone Shift Selects the SA T input for the Main Zone. Selects the VCR input for the Main Zone. Selects the SA T input for Zone 2. Selects the VCR input for Zone 2. Selects the SA T input for the Record Zone.
Basic Operation SDP-40 2-15 DVD-1 DVD -2 L D TV CD T APE TU NER MENU PVR SAT FP BLUE OSD VCR AUX GAME MAIN SHIFT STA T 7 / 5 2 CH MUTE MUSIC ZONE REC L I G H T MODE VOL Button Zone 2 Record Zone Shift Main Zone 5 7 6 9 8 10 T oggles the FRONT P ANEL DISPLAY menu ST ATUS parameter between ALW AYS OFF and its current setting.
Basic Operation JBL 2-16 DVD-1 DVD -2 L D TV CD T APE TU NER MENU PVR SAT FP BLUE OSD VCR AUX GAME MAIN SHIFT STA T 7 / 5 2 CH MUTE MUSIC ZONE REC L I G H T MODE VOL Button Main Zone Zone 2 Record Zone Shift Displays the Main Zone two-line status for 2 seconds.
Basic Operation SDP-40 2-17 DVD-1 DVD -2 L D TV CD T APE TU NER MENU PVR SAT FP BLUE OSD VCR AUX GAME MAIN SHIFT STA T 7 / 5 2 CH MUTE MUSIC ZONE REC L I G H T MODE VOL Button Main Zone Zone 2 Record Zone Shift 16 Selects the THX mode family for the current input source.
Basic Operation JBL 2-18 3. When the INPUT SETUP menu ZONE2 IN or RECORD IN parameter is set to ANLG, the Zone 2 or Record Zone audio output connectors are not available when the 5.1a BYP ASS listening mode is activated. However, it is possible to have a 5.
Basic Operation SDP-40 2-19 Record Zone Two-Line Status Opens on the on-screen and front panel displays whenever the SDP-40 detects a Record Zone status change. The Record Zone two-line status indicates the current input, input source, and volume level selected in the Record Zone.
Basic Operation JBL 2-20 page, pressing the ST A T button again will close the menu. If this occurs, begin again with step 1. 3. When the desired status menu page has been opened, press the remote control and arrow buttons to scroll upward and downward through all status menu parameters included on the open page.
Basic Operation SDP-40 2-21 D ST A TUS •P rovides information about Dolby Digital sources. • Includes L, C, R, SL, SR, and LFE level meters. Parameter Possible Settings INPUT The current input MODE The current listening mode CHANNELS 3/2.1, 3/2, 3/1, 2/2, 2/1, 2/0, 1/0 BIT RA TE 32 to 640kbps EX ENCODING ON, OFF SAMPLE RA TE 48kHz 2.
Basic Operation JBL 2-22 5.1 ANALOG ST A TUS •P rovides information about 5.1-channel analog sources. • Includes L, C, R, SL, SR, and LFE level meters. Parameter Possible Settings INPUT The current input MODE The current listening mode INPUT TYPE ANLG SAMPLE RA TE 44.
Basic Operation SDP-40 2-23 ST A TUS MENU P ARAMETER DESCRIPTIONS 2.0 ENCODING MA TRIX, NONE Indicates whether or not a matrix-encoded source is detected. When the parameter setting is MA TRIX, a matrix-encoded source is detected. When the parameter setting is NONE, a matrix-encoded source is not detected.
Basic Operation JBL 2-24 INPUT Indicates the current input (i.e. DVD1). INPUT TYPE ANLG, BYP , PCM, --- Indicates the input source that is present. When the parameter setting is ANLG, an analog audio source is present and the MAIN ADV menu ANALOG BYP ASS parameter is set to OFF .
3 SETUP SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 INPUT SETUP . . . . . . . . . . . . . . . . .
SETUP JBL 3-2 SETUP Selecting the MAIN MENU SETUP option opens the SETUP menu shown below , which can be used to configure the SDP-40. INPUTS Prompts the selection of the desired input (i.
SETUP SDP-40 3-3 LOCK OPTIONS Opens the LOCK OPTIONS menu, which can be used to protect MODE ADJUST, AUDIO CONTROLS, and SETUP menu branch parameter settings from accidental changes. Refer to page 3-50 for more information. INPUT SETUP Selecting the SETUP menu INPUTS option prompts the selection of the desired input (i.
SETUP JBL 3-4 CHANGING INPUT NAMES Selecting the INPUT SETUP menu NAME option opens the INPUT NAME menu shown below , which can be used to customize or restore the factory-default name of the selected input. Factory-default input names correspond to front panel and remote control input selection button labels.
SETUP SDP-40 3-5 •P ress the arrow button to return to the previous character space. When the cursor is positioned in the first character space, pressing the arrow button will close the EDIT INPUT NAME drop-down menu.
SETUP JBL 3-6 ASSIGNING AUDIO & VIDEO INPUT CONNECTORS The SDP-40 has 12 configurable inputs, each of which can be assigned to its 13 digital audio, 8 analog audio, 5 composite video, 8 S-video, or 4 component video input connectors.
SETUP SDP-40 3-7 When no digital audio input connector is assigned, the SDP-40 automatically sets the: • MAIN ADV menu INPUT SELECT parameter to ANALOG •I NPUT SETUP menu ZONE2 IN parameter to ANLG •I NPUT SETUP menu RECORD IN parameter to ANLG ANALOG IN ANALOG-1 to 8, 5.
ON OFF SETUP JBL 3-8 ANLG IN LVL AUTO, -18 to +12dB Opens the ANLG IN L VL menu shown above, which can be used to adjust 2-channel analog audio input levels for the selected input. Despite attempts at standardization, analog sources still have a wide range of input levels.
SETUP SDP-40 3-9 AUTO ON, OFF Activates automatic adjustment of 2-channel analog audio input levels. When ON is selected, the SDP-40 automatically monitors and optimizes 2-channel analog audio input levels. When the input signal is too high, the SDP-40 quickly decreases input levels to avoid overload.
SETUP JBL 3-10 VIDEO IN COMPOSITE-1 to 5, S-VIDEO-1 to 8, NONE Opens the VIDEO IN menu shown below , which can be used to assign a composite or S-video input connector for the selected input. Note: • Composite video output connectors are available when a composite or S-video source is present.
SETUP SDP-40 3-11 SELECTING PREFERRED LISTENING MODES The SDP-40 allows the selection of four preferred listening modes for each Main Zone input, including one listening mode each for 2-channel, Dolby Digital, dts(-ES), and 5.1-channel analog sources.
SETUP JBL 3-12 Selecting Preferr ed Listening Modes (continued from page 3-11) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLA YS VOLUME CONTROLS TRIGGE.
SETUP SDP-40 3-13 was activated the last time a 2-channel source was present. The SDP-40 will not activate a listening mode unless a 44.1 or 48kHz PCM digital source is present. The listening modes are not compatible with 88.2 or 96kHz, Dolby Digital, or analog sources.
SETUP JBL 3-14 CONFIGURING ADV ANCED INPUT SETTINGS The SDP-40 allows the assignment of one digital and one analog audio input connector for each input.
SETUP SDP-40 3-15 Parameter Possible Settings INPUT SELECT DIGIT AL, ANALOG, AUTO ANALOG BYP ASS ON, OFF S-VIDEO 16:9 AUTO, OFF S-VIDEO OSD 4:3 ON, OFF COMPONENT OSD ON, OFF INPUT SELECT DIGIT AL, ANALOG, AUTO Controls the interaction of the digital and analog audio input connectors assigned for the selected Main Zone input.
DIGIT AL ANALOG AUTO SETUP JBL 3-16 Configuring Advanced Input Settings (continued from page 3-15) INPUT SELECT Parameter Settings The SDP-40 sends the assigned digital audio input connector to the Main Zone audio output connectors. The SDP-40 ignores the assigned analog audio input connector.
SETUP SDP-40 3-17 S-VIDEO OSD 4:3 ON, OFF Controls the on-screen display aspect ratio when the display device is connected to a Main Zone S-video output connector . Aspect ratio refers to the size of the picture or the display device screen. A 4:3 aspect ratio is almost square.
DMIX (Downmix) DIGIT AL SETUP JBL 3-18 Configuring Advanced Input Settings (continued from page 3-17) ANLG (Analog) ZONE2 & RECORD IN Parameter Settings The SDP-40 sends the assigned digital audio input connector to the Zone 2 or Record Zone audio output connectors.
SETUP SDP-40 3-19 RECORD ADV ANCED Selecting the INPUT SETUP menu RECORD ADVANCED option opens the RECORD ADV menu shown above, which can be used to configure advanced Record Zone input settings. All RECORD ADV menus are shown in the Appendix on page A-8.
SETUP JBL 3-20 Configuring Advanced Input Settings (continued from page 3-19) ANLG IN LVL -18 to +12dB Allows adjustment of analog audio input levels for input signals sent to the Record Zone digital audio output connectors. The SDP-40 applies these adjustments to input signals before passing them to the Record Zone digital audio output connectors.
SETUP SDP-40 3-21 SPEAKER SETUP Selecting the SETUP menu SPEAKERS option opens the SPEAKER SETUP menu shown below , which can be used to configure the Main Zone audio output connectors for the desired speaker setup. The Main Zone includes 10 unbalanced audio output connectors labeled Front L/R, Center, LFE, Subwoofer L/R, Side L/R, and Rear L/R.
Custom Speaker Setups Selecting the CROSSOVER SETUP menu CUSTOM SETUP option opens the CUSTOM SETUP menu shown above, which can be used to assign independent crossover points for each Main Zone audio output connector . Crossover points can be selected in 10Hz increments within a 30 to 120Hz range.
SETUP SDP-40 3-23 Highpass Filter Lowpass Filter 10 20 50 100 200 500 1k dB 0 0 -12 -24 -36 -48 0 0 -60 Hz Highpass filters attenuate low-frequency signals at 24dB per octave. The curves in the graph above indicate the frequency response of each crossover point.
SETUP JBL 3-24 SYNTHESIS 7CH Speaker Setups Selecting the CROSSOVER SETUP menu SYNTHESIS 7CH SETUP option opens the SYNTHESIS 7CH SPEAKER SETUP screen shown above, which indicates that pressing the arr ow button will auto- matically configure the Main Zone audio output connectors for a SYNTHESIS 7CH speakers setup.
SYNTHESIS 7CH SETUP Menu Default Setting Default Setting Possible Settings Possible Settings CUSTOM SETUP Menu Parameter SETUP SDP-40 3-25 Speaker Setup Parameters SYNTHESIS 7CH SETUP SET CROSSOVERS S.
REAR L/R SPEAKERS FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120H NONE SUB XOVER FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz SETUP JBL 3-26 Setting Crossover P.
SETUP SDP-40 3-27 When a SYNTHESIS 7CH speaker setup is selected, the FRONT L/R parameter cannot be adjusted. The SDP-40 automatically applies a 80Hz crossover point to the Front L/R output connectors. CENTER FULL, 30 to 120Hz, THX 80Hz, NONE Assigns a crossover point for the Main Zone audio output connector labeled Center.
SETUP JBL 3-28 REAR L/R FULL, 30 to 120Hz, THX 80Hz, NONE Assigns a crossover point for the Main Zone audio output connectors labeled Rear L/R. When a custom speaker setup is selected, the REAR L/R parameter opens the REAR L/R SPEAKERS menu shown on page 3-26, which can be used to select a crossover point for the Rear L/R output connectors.
SETUP SDP-40 3-29 SUB L/R MONO, STEREO, NONE Configures the Main Zone audio output connector labeled Subwoofer L/R for a speaker setup that includes one, two, or no subwoofer(s).
SETUP JBL 3-30 LFE ON, OFF Activates and deactivates the Main Zone audio output connector labeled LFE. When a custom speaker setup is selected: • Select ON to activate the LFE output connector, configuring the Main Zone audio output connectors for a 7.
SETUP SDP-40 3-31 UL TRA2 SUB ON, OFF Select ON if the subwoofer using the Main Zone audio output connectors labeled Subwoofer L/R is THX Ultra2-certified.
SETUP JBL 3-32 CALIBRA TING SPEAKER DIST ANCES & OUTPUT LEVELS The SDP-40 offers manual calibration of speaker distances and output levels. Calibration helps to ensure accurate output signal arrival time and level at the primary listening position.
Output Level Settings Default Setting Default Setting Possible Settings Possible Settings Speaker Distance Settings Parameter FRONT LEFT CENTER FRONT RIGHT SIDE LEFT REAR LEFT REAR RIGHT SIDE RIGHT MONO SUB* SUB RIGHT LFE UNITS +0.0ft +0.0dB -18.0 to +12.
SETUP SDP-40 3-34 MANUAL CALIBRA TION Selecting the SPEAKER SETUP menu MANUAL option opens the MANUAL SPEAKER SETUP menu shown below , which can be used to manually calibrate speaker distances and output levels. The table below indicates available manual calibration options.
SETUP JBL 3-35 Performing Manual Speaker Distance Calibration Selecting the MANUAL SPEAKER SETUP menu SPEAKER DIST ANCES option opens the SPEAKER DIST ANCES menu shown below , which can be used to manually calibrate speaker distances. SPEAKER DIST ANCES MANUAL SPEAKERS SETUP To manually calibrate speaker distances: 1.
SETUP SDP-40 3-36 Performing Manual Output Level Calibration Selecting the MANUAL SPEAKER SETUP menu LEVELS CALIBRA TION option opens the LEVELS CALIBRA TION menu shown below , which can be used to manually calibrate output levels.
SETUP JBL 3-37 Performing Manual Output Level Calibration (continued from page 3-36) INTERNAL NOISE TEST Opens the INTERNAL NOISE message shown on the previous page, which indicates that the internal noise test generates loud calibration noise signals.
SETUP SDP-40 3-38 Note: The internal noise and DACS CALIBRA TON modes will turn on TRIGGER1 . DACS CALIBRA TION Selecting DACS CALIBRA TION accesses the SPEAKER LEVEL ADJUST menu (pictured on page 3-36). DACS CALIBRA TION requires an external noise source.
SETUP JBL 3-39 SETTING BASS PEAK LIMITERS Selecting the LEVELS CALIBRA TION menu BASS PEAK LIMITERS option opens the BASS PEAK LIMITERS menu shown below , which can be use d to set amplitude limits fo.
SETUP SDP-40 3-40 CAL NOISE ON, OFF Determines whether bass peak limiters are set with an internal or external calibration source. When ON is selected, the SDP-40 activates an internal calibration noise signal to set bass peak limiters. When OFF is selected, the SDP-40 deactivates the internal calibration noise signal.
SETUP JBL 3-41 REAR P ANEL CONFIG Selecting the SETUP menu REAR P ANEL CONFIG option opens the REAR P ANEL CONFIG menu shown below , which can be used to configure the analog audio input connectors as eight stereo connectors or as five stereo and one 5.
SETUP SDP-40 3-42 DISPLA Y SETUP Selecting the SETUP menu DISPLAYS option opens the DISPLA Y SETUP menu shown below , which can be used to customize the on-screen and front panel displays, restore audio/video synchronization, and create and activate a custom unit name.
SETUP JBL 3-43 EDIT CUSTOM NAME Opens the EDIT CUSTOM NAME drop-down menu shown above, which can be used to create a custom unit name. The factory- default unit name is SDP-40. To c r e a te a custom unit name: 1. Follow the EDIT CUSTOM NAME menu path shown above to open the EDIT CUSTOM NAME drop-down menu.
SETUP SDP-40 3-44 ON-SCREEN DISPLA Y Selecting the DISPLAY SETUP menu ON-SCREEN DISPLA Y option opens the ON-SCREEN DISPLAY menu shown below , which can be used to customize the on-screen display .
SETUP JBL 3-45 On-Screen Display (continued from page 3-44) POSITION TOP , CENTER, BOTTOM Controls the vertical alignment of the two-line status on the display device screen. When TOP is selected, the two-line status appears near the top of the display device screen.
SETUP SDP-40 3-46 FRONT P ANEL DISPLA Y Opens the FRONT P ANEL DISPLA Y menu shown below , which can be used to customize the front panel display . FRONT PANEL DISPLA Y DISPLA YS SETUP Default Possibl.
SETUP JBL 3-47 VOLUME CONTROL SETUP Selecting the SETUP menu VOLUME CONTROLS option opens the VOLUME CONTROL SETUP menu shown below , which can be used to configure Main Zone, Zone 2, and Record Zone volume levels.
SETUP SDP-40 3-48 REC PWR ON LAST L VL, -80 to +6dB Selects the volume level at which the Record Zone activates. When a value is selected, the SDP-40 automatically sets Record Zone REC PWR ON VOLUME C.
SETUP JBL 3-49 T rigger Setup (continued from page 3-48) REMOTE ONL Y ON, OFF Configures the selected trigger output connector for remote operation. Select the ON setting to configure the selected connector for remote operation. Select the OFF setting to configure the selected connector for program operation.
SETUP SDP-40 3-50 When configured for program operation, the connector activates when the associated inputs or listening modes are activated and deactivates when the associated inputs or listening modes are deactivated.
SETUP JBL 3-51 SETUP LOCKED, UNLOCKED Protects SETUP menu branch settings from accidental changes. When LOCKED is selected, SETUP m enu branch settings cannot be adjusted.
4 AUDIO CONTROLS AUDIO CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Bass • T reble • Tilt EQ • Loudness • Balance • Fader • Zone2 Balance • Record B.
• The BASS, TREBLE, TIL T EQ, LOUDNESS, BALANCE, and FADER parameters affect the Main Zone audio output connectors. This includes all Main Zone inputs and listening modes, except the 5.1a BYP ASS and 2CH BYP ASS listening modes. • The ZONE2 BALANCE parameter affects the Zone 2 audio output connectors, including all Zone 2 inputs.
AUDIO CONTROLS SDP-40 4-3 BASS -6.0 to +6.0 Controls the amount of low-frequency boost or cut applied to the Main Zone audio output connectors labeled Front L/R, Center, LFE, and Subwoofer L/R. The graph shown at the right indicates the frequency response of all BASS parameter settings.
AUDIO CONTROLS JBL 4-4 TREBLE -6.0 to +6.0 Controls the amount of boost or cut applied to the Main Zone audio output connectors labeled Front L/R and Center. The graph shown at the right indicates the frequency response of all TREBLE parameter settings.
AUDIO CONTROLS SDP-40 4-5 TIL T EQ -3.0 to +3.0 Controls the amount of tilt equalization applied to the Main Zone audio output connectors labeled Front L/R, Center, LFE, and Subwoofer L/R. This parameter setting affects the entire frequency spectrum with a hinge point at 1kHz.
AUDIO CONTROLS JBL 4-6 LOUDNESS ON, OFF Controls the amount of low-frequency boost that is automatically applied to the Main Zone audio output connectors labeled Front L/R, Center, LFE, and Subwoofer L/R. When ON is selected, loudness compensation is automatically applied based on volume level.
AUDIO CONTROLS SDP-40 4-7 BALANCE L< to <|> to >R Controls the left-to-right balance of the Main Zone audio output connectors labeled Front L/R. Note: When the Shift command bank is activated: •P ressing the MENU button centers the Main Zone BALANCE parameter.
5 MODE ADJUST MODE ADJUST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Listening Mode Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Preferred Listening Mode Selection Parameters • Mode Buttons • Mode Family Selection Buttons Listening Mode Descriptions .
MODE ADJUST JBL 5-2 MODE ADJUST Selecting the MAIN MENU MODE ADJUST option opens the MODE ADJUST menu shown at the left, which prompts the selection of the desired listening mode. Selecting a listening mode opens the corresponding listening mode menu, which can be used to customize the selected listening mode.
• If the DVD1 input is selected while a 2-channel sour ce is present, the SDP-40 will automatically activate the FILM listening mode. If a 5.1-channel analog source becomes present, the SDP-40 will automatically activate the 5.1a FILM listening mode.
2-Channel Dolby Digital dts(-ES) 5.1-Channel Analog Button Input Source MODE ADJUST JBL 5-4 MODE BUTTONS The front panel and remote control Mode buttons can be used to audition listening modes with the current Main Zone input source.
MODE ADJUST SDP-40 5-5 LISTENING MODE DESCRIPTIONS The SDP-40 offers an assortment of listening modes for 2-channel, Dolby Digital, dts(-ES), and analog sources. Listening mode descriptions begin below and continue in the order shown on the MODE ADJUST menu.
MODE ADJUST JBL 5-6 TV •A proprietar y listening mode. • Similar to the FILM listening mode, but specifically tailored for broadcast sources. • Designed for enhanced playback of 2-channel stereo or matrix- encoded broadcast sources. •R ecommended for 2-channel stereo or matrix-encoded broadcast sources.
MODE ADJUST SDP-40 5-7 MUSIC SURR •A proprietar y listening mode. • Similar to the MUSIC SURROUND listening mode available in other JBL products. • Designed for enhanced playback of 2-channel stereo music sources recorded in real spaces and for playback of recordings that contain added reverb.
MODE ADJUST JBL 5-8 PLII MOVIE • Similar to the PRO LOGIC listening mode, but uses full- frequency stereo surround channels to realistically increase the perceived width of the listening space. • Designed for playback of Dolby Surround-encoded sources.
MODE ADJUST SDP-40 5-9 PRO LOGIC • Designed for playback of Dolby Surround-encoded sources. • Decodes four channels from Dolby Surround-encoded sources. • Uses a mono surround channel with a high-frequency rolloff above 7kHz. •A vailable for comparison purposes, particularly with the FILM, PLII MOVIE, and FILM listening modes.
MODE ADJUST JBL 5-10 NIGHTCLUB • Designed for playback of “dry” music sources that benefit from the addition of room reflections, especially music sources that lack ambience in the recording. • Generates early reflections to simulate small, intimate listening spaces.
MODE ADJUST SDP-40 5-11 CHURCH • Uses a reverb algorithm to emphasize the rich, smooth, reverberant decay characteristic of small and medium listening spaces with long reverberation time relative to their size, such as churches and chambers.
MODE ADJUST JBL 5-12 P ANORAMA • Designed for playback of stereo and matrix-encoded sources. • Uses proprietary algorithms to move the stereo image outward from the front speakers, producing a wider stereo field with greater depth. • Depends on proper location of the primary listening position and front speakers.
MODE ADJUST SDP-40 5-13 To calibrate the P ANORAMA listening mode: 1. Remove all obstructions between the primary listening position and the speakers. 2. Make sure the distances between the primar y listening position and the speakers are properly measured.
MODE ADJUST JBL 5-14 PA R T Y • Designed for playback of stereo sources. • Sends stereo sources to all channels. • Recommended for background music. Parameter OUTPUT LEVELS Refer to page 5-32 CUSTOM Refer to page 5-33 Listening mode menu parameter descriptions begin on page 5-34.
MODE ADJUST SDP-40 5-15 MONO SURROUND • Designed for playback of mono sources. • Sends mono sources to all channels. Parameter OUTPUT LEVELS Refer to page 5-32 CUSTOM Refer to page 5-33 Listening mode menu parameter descriptions begin on page 5-34.
MODE ADJUST JBL 5-16 5.1 TV •A proprietar y listening mode. • Similar to the 5.1 FILM listening mode, but specifically tailored for broadcast sources. • Designed for enhanced playback of 5.1-channel Dolby Digital broadcast sources. •R ecommended for 5.
5.1-Channel Dolby Digital 5.1-Channel THX Surround EX Dolby Digital (Flagged) 5.1-Channel THX Surround EX Dolby Digital (Non-Flagged) MODE ADJUST SDP-40 5-17 5.1 UL TRA2, 5.1 SurEX, & 5.1 Listening mode name differs depending on the encoding present in the input source, the SURROUND EX parameter setting, and the speaker setup.
MODE ADJUST JBL 5-18 5.1 UL TRA2, 5.1 SurEX, & 5.1 (continued from page 5-17) • Designed for playback of 5.1-channel Dolby Digital film sources. • Allows 7-channel playback of 5.1-channel Dolby Digital sources without THX Surround EX encoding.
MODE ADJUST SDP-40 5-19 5.1 MUSIC • Designed for playback of 5.1-channel Dolby Digital music sources. • The 5.1 MUSIC listening mode is not available unless both side and rear speakers are present. • Applies ASA processing to signals sent to the rear speakers.
MODE ADJUST JBL 5-20 DIGIT AL EX & DIGIT AL (continued from page 5-19) Note: The SDP-40 cannot automatically detect Dolby Digital Surround EX encoding in non-flagged 5.1- channel Dolby D igital sources. A non-flagged input source does not include information in the input signal that identifies Dolby Digital Surround EX encoding.
MODE ADJUST SDP-40 5-21 5.1 2-CHANNEL •D esigned for converting 5.1-channel Dolby Digital input signals into 2-channel LOGIC7-encoded output signals. • Sends downmixed 5.1-channel Dolby Digital input signals to the front speakers and the subwoofer.
MODE ADJUST JBL 5-22 5.1 MONO SURR • Designed for playback of Dolby Digital mono sources. • Sends mono sources to all channels. Parameter OUTPUT LEVELS Refer to page 5-32 CUSTOM Refer to page 5-33 Listening mode menu parameter descriptions begin on page 5-34.
MODE ADJUST SDP-40 5-23 FILM & FILM • Listening mode name differs depending on the encoding present in the input source, the DECODING parameter setting, and the speaker setup. Refer to the previous page for more information. •A proprietar y listening mode.
MODE ADJUST JBL 5-24 MUSIC & MUSIC • Listening mode name differs depending on the encoding present in the input source, the DECODING parameter setting, and the speaker setup. Refer to page 5-22 for more information. •A proprietar y listening mode.
MODE ADJUST SDP-40 5-25 •A pplies THX timbre matching to minimize timbre differences between the front and surround channels, which results in smoother sound movements between them.
MODE ADJUST JBL 5-26 MUSIC • Designed for playback of 5.1-channel dts music sources. • The MUSIC listening mode is not available unless both side and rear speakers are present. • Applies ASA processing to signals sent to the rear speakers. Refer to the ASA parameter description on page 3-31 for more information.
MODE ADJUST SDP-40 5-27 & 2-CHAN • Designed for converting 5.1- or 6.1-channel dts(-ES) input signals into 2-channel LOGIC7-encoded output signals. • Sends downmixed 5.1- or 6.1-channel dts(-ES) input signals to the front speakers and the subwoofer.
MODE ADJUST JBL 5-28 5.1a MUSIC •A proprietar y listening mode. • Similar to the 5.1a FILM listening mode, but specifically tailored for music sources. • Designed for enhanced playback of 5.1-channel analog music sources. • Recommended for 5.1-channel analog music sources.
MODE ADJUST SDP-40 5-29 • Designed for playback of 5.1-channel analog film sources. • Allows 7-channel playback of 5.1-channel analog sour ces without THX Surround EX encoding. • Applies THX re-equalization to simulate high-frequency rolloffs that occur in movie theaters.
MODE ADJUST JBL 5-30 5.1a MUSIC • Designed for playback of 5.1-channel analog music sources. • The 5.1a MUSIC listening mode is not available unless both side and rear speakers are present. • Applies ASA processing to signals sent to the rear speakers.
MODE ADJUST SDP-40 5-31 5.1a 2-CHANNEL • Designed for converting 5.1-channel analog input signals into 2-channel LOGIC7-encoded output signals. • Sends downmixed 5.
MODE ADJUST JBL 5-32 2CH BYP ASS • Designed for playback of 2-channel analog sources. • Sends analog audio input signals to the Main Zone audio output connectors labeled Front L/R.
MODE ADJUST SDP-40 5-33 CUSTOM Opens the CUSTOM menu shown below , which can be used to compare custom and factory-default versions of the selected listening mode and to restore the factory-default version of the selected listening mode.
MODE ADJUST JBL 5-34 RESET MODE (continued from page 5-33) 2. When RESET MODE message appears, press the arrow button to restore the factory-default version of the selected listening mode. Press the arrow button to close the message without restoring the factor y-default version of the selected listening mode.
MODE ADJUST SDP-40 5-35 BASS ENHANCE ON, OFF Selecting the ON setting enhances stereo bass, which results in low-frequency reproduction that is less localizable and more realistic in the listening space.
MODE ADJUST JBL 5-36 Listening Mode Menu Parameter Descriptions (continued from page 5-35) CTR WIDTH MIN, 1 to 6, MAX Adjusts the center image. When MIN is selected, the center image is heard from just the center speaker . When MAX is selected, the center image is heard from just the front left and right speakers as a “phantom” center image.
MODE ADJUST SDP-40 5-37 • The ST A TUS menu includes an SB level meter when the DECODING parameter is set to ON and a 5.1-channel dts source is present or when the DECODING parameter is set to AUTO and a 5.1-channel matrix-encoded or 6.1-channel discrete-encoded dts-ES source is present.
MODE ADJUST JBL 5-38 Listening Mode Menu Parameter Descriptions (continued from page 5-37) LFE OFF , -30 to +12dB Controls the output level of the Main Zone audio output connector labeled LFE. The OUTPUT LEVELS menu does not include the LFE parameter unless an LFE subwoofer is present.
MODE ADJUST SDP-40 5-39 OUTPUT LEVELS Opens the OUTPUT LEVELS menu, which can be used to adjust output levels for the Main Zone audio output connectors labeled Center, Subwoofer L/R, LFE, Side L/R, and Rear L/R. Refer to page 5-32 for more information.
MODE ADJUST JBL 5-40 Listening Mode Menu Parameter Descriptions (continued from page 5-39) SIZE 4 to 20 or 30m Adjusts listening space length within a 4 to 20 or 30m range (depending on the listening mode). Increase the size of the space to increase the reverb effect.
MODE ADJUST SDP-40 5-41 SURR ROLLOFF 500Hz to 20.0kHz, OFF Applies high-frequency attenuation control to the Main Zone audio output connectors labeled Side L/R and Rear L/R.
MODE ADJUST JBL 5-42 Listening Mode Menu Parameter Descriptions (continued from page 5-41) SURROUND MIX -5 to +5dB Controls the relative level of surround channel information sent to the Main Zone audio output connectors labeled Front L/R. It is recommended to set this parameter to +2 or +3dB for all input sources.
6 Tr oubleshooting & Maintenance T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Restoring Factory-Default Settings .
T roubleshooting & Maintenance JBL 6-2 TROUBLESHOOTING The SDP-40 does not power on. 1. Make sure the rear panel power switch is set to the | (“on”) position. 2. Attempt to deactivate standby mode with both the front panel and remote control standby buttons.
Tr oubleshooting & Maintenance SDP-40 6-3 A humming sound is present in the audio. 1. If a cable TV connection is present, disconnect the cable from the wall outlet. If this eliminates the humming sound, a ground loop isolation device is required.
T roubleshooting & Maintenance JBL 6-4 ROUTINE MAINTENANCE The following routine maintenance should be performed on a periodic basis: • Clean the SDP-40 exterior surface with a soft, lint-free cloth. Do not use alcohol, benzene, acetone-based cleaners, or strong commercial cleaners.
Tr oubleshooting & Maintenance SDP-40 6-5 Note: The Mute button must be pressed within 2 seconds of deactivating standby mode. Otherwise, the "MUTE ON" message will appear on the on-screen and front panel displays. If this occurs, too much time has passed.
A Appendix Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4 Menu T rees . . . . . . . . . . . . . . . . . . . . .
Main Zone Audio Performance (continued) Appendix JBL A-2 SPECIFICA TIONS Audio Input & Output Connectors •8 stereo (RCA) or 5 stereo and one 5.1-channel connectors •6 S/PDIF coaxial (RCA), 6 S.
Microphone Input Connectors Composite & S-video Per formance (continued) Zone 2 & Record Zone Audio Performance (continued) Appendix SDP-40 A-3 • 100 Ω in parallel with 150pF (RCA connecto.
Appendix JBL A-4 Specifications (continued from page A-3) Specifications are subject to change without notice. Other •1 power on/off and 2 programmable connectors on detachable screw terminals (+12 VDC, 0.
ON-SCREEN DISPLA Y ST ATUS 2 SECONDS POSITION TOP FORMA T NTSC BACKGROUND ON REMOTE ST ATE ON OFF , 1 to 60ms EDIT CUSTOM NAME SDP-40 ^ WY BUTTONS TO EDIT UP TO 20 CHARACTERS V BUTTON TO ADVANCE FRONT.
Appendix JBL A-6 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLA YS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUT SETUP DVD1 DVD2 LD TV SA T VCR CD PVR GA.
INPUT 96kHz 88.2kHz 48kHz 44.1kHz Appendix SDP-40 A-7 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLA YS VOLUME CONTROLS TRIGGERS LOCK OPTIONS INPUT SET.
Appendix JBL A-8 Menu T rees (continued from page A-7) DVD1 MAIN ADV INPUT SELECT DIGIT AL ANALOG BYPASS OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD ON CD MAIN ADV INPUT SELECT DIGIT AL ANA.
CUSTOM SETUP FRONT L/R 40Hz CENTER 60Hz SIDE L/R 60Hz REAR L/R 60Hz SUB L/R MONO SUB XOVER 40Hz LFE OFF UL TRA2 SUB OFF BGC N/A ASA APAR T Appendix SDP-40 A-9 MAIN MENU MODE ADJUST AUDIO CONTROLS SETU.
Appendix JBL A-10 A-10 Appendix A-10 75 to 120dB BASS PEAK LIMITERS CAL NOISE ON L/R LIMITER ON L/R LIMIT ADJ 100dB LFE LIMITER ON LFE LIMIT ADJ 100dB !CAUTION! HIGH AUDIO LEVELS INTERNAL NOISE !CAUTION! HIGH AUDIO LEVELS !CAUTION! MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP AUDIO CONTROLS AUDIO CONTROLS BASS +0.
Appendix SDP-40 A-11 A-11 A-11 MODE ADJUST FILM TV MUSIC MUSIC SURR PLII + PLII MOVIE PLII MUSIC PRO LOGIC FILM MUSIC NIGHTCLUB CONCERT HALL CHURCH CA THEDRAL P ANORAMA PAR TY 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.1 FILM 5.1 TV 5.1 MUSIC 5.1 * 5.1 MUSIC DIGIT AL* 5.
Appendix JBL A-12 A-12 Appendix A-12 2-CHAN CENTER MIX +0dB SURROUND MIX +0dB CNTR DL Y SAMPLES +0 MASTER LEVEL +0dB LFE MIX +0.0dB DECODING AUTO SUB L/R L VL +0dB CUSTOM 5.1 FILM VOCAL ENHANCE +0.0dB 5 SPKR ENHANCE ON BASS ENHANCE OFF RE-EQUALIZER ON REAR DL Y OFFSET 15ms COMPRESSION OFF LFE MIX +0.
Appendix SDP-40 A-13 A-13 A-13 Selecting the listening mode menu CALIBRA TION, OUTPUT LEVELS, or CUSTOM option opens the corresponding menu shown below . The CALIBRATION option is available for the P ANORAMA listening mode. The OUTPUT LEVELS and CUSTOM options are available for most listening modes.
Appendix JBL A-14 A-14 Appendix JBL A-14 SURROUND EX AUTO ON OFF VOCAL ENHANCE +6.0dB +3.0dB +0.0dB SOURCE RIGHT LEFT & RIGHT LEFT L< <|> >R INPUT BALANCE SOUND ST AGE FRONT NEUTRAL REAR LFE MIX -20.0 or -10.0 to +0.0dB -127 +0 +127 LISTENER POSITION LIVENESS 30ms to 20.
SDP-40 A-15 JBL A-15 A-15 A-15 A-15 Menu T rees (continued from page A-14) ST ATUS PG1 INPUT MODE CHANNELS BIT RA TE ENCODING LC R S L S RS B LFE XX XXX X X ST ATUS PG2 WORD LENGTH SAMPLE RA TE 0 -6 -15 -30 -45 dB ST ATUS PG1 INPUT MODE CHANNELS BIT RA TE EX ENCODING LC R S L S RS B LFE XX XXX X X ST ATUS PG2 SAMPLE RA TE 2.
Appendix JBL A-16 AUX TUNER T APE GAME PVR CD VCR SA T TV LD DVD2 DVD1 INPUT SETUP MAIN ADV ANCED RECORD ADV ANCED INST ALLA TION WORKSHEET NAME DIGIT AL IN ANALOG IN ANLG IN LVL VIDEO IN COMPONENT IN 2-CH D INPUT SELECT ZONE2 IN RECORD IN 5.
Appendix SDP-40 A-17 LOCK OPTIONS VOLUME CONTROL SETUP REAR P ANEL CONFIG SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DIST ANCES LEVELS CALIBRATION Installation Worksheet (continued from pa.
Appendix JBL A-18 TRIGGER 2 SETUP TRIGGER 1 SETUP DISPLA Y SETUP AUDIO CONTROLS ON-SCREEN DISPLA Y FRONT P ANEL DISPLA Y ST ATUS POSITION FORMA T BACKGROUND ST ATUS BRIGHTNESS REMOTE ST ATE BASS TREBLE TILT EQ LOUDNESS BALANCE F ADER ZONE2 BALANCE RECORD BALANCE A/V SYNC DELA Y CUSTOM NAME EDIT CUSTOM NAME Circle all parameters set to ON.
I Index I-1 SYMBOLS & LOGOS Documentation Conventions, ii , see Dolby , see also dts, dts-ES, dts(-ES) , see dts Neo:6 , see ES , see LOGIC7 , see THX NUMBERS 2.0 ENCODING Parameter , 2-21, 2-23 2-CH Parameter , 3-11, 3-12 to 3-13 (menu ill.) , 5-3, A-7 (menu ill.
Index I-2 A (continued) AUTO Parameter , 3-8 to 3-9, A-7 B BACKGROUND Parameter , 3-44, 3-45, A-5 BALANCE Parameter , 4-2, 4-7, A-10 BASS CONTENT Parameter , 5-12, 5-34, A-13 BASS ENHANCE Parameter , .
E EDIT CUSTOM NAME Option, 3-42, 3-43, A-5 EDIT INPUT NAME Option, 3-4 to 3-5 (menu ill.) , A-7 EFFECT LVL Parameter , 5-10, 5-11, 5-12, 5-14, 5-21, 5-36, A-13 DECODING Parameter , 5-23, 5-24, 5-25, 5.
Index I-4 L (continued) FILM Listening Mode, 5-4, 5-5, A-11 (menu ill.) MUSIC Listening Mode, 5-4, 5-6, A-11 (menu ill.) MUSIC SURR Listening Mode, 5-7, A-11 (menu ill.) TV Listening Mode, 5-4, 5-6, A-14 (menu ill.) LOUDNESS Parameter , 4-2, 4-6 (frequency-response graph), A-10 LOW FREQ WIDTH Parameter , 5-12, 5-38, A-11 Lowpass Filter , 3-23 (ill.
P (continued) P ARAMETERS Preferred Listening Mode Selection, 5-3 Selecting, 2-11 to 2-12 POSITION Parameter , 3-44, 3-45, A-5 Power Switch, 2-5 PRE-DELAY Parameter , 5-10, 5-11, 5-39, A-14 Preferred Listening Mode Selection Parameters 2-CH Parameter , 3-11, 3-12 to 3-13 (menu ill.
Index I-6 S (continued) SPEAKER SETUP Menu, 3-2, 3-21 to 3-40 (ills.) , A-5 (ill.) , A-9 to A-10 (ills.) SPEAKER SETUP P ARAMETERS ASA, 3-25, 3-31 to 3-32, A-9, BGC, 3-25, 3-31, A-9 CENTER, 3-25, 3-26 (menu ill.) , 3-27, A-9 (menu ill.) , A-20 FRONT L/R, 3-25, 3-26 to 3-27 (menu ill.
SYNTHESIS LIMITED W ARRANTY The JBL Synthesis products listed below are warranted f or the period stated from the date of original pur chase: Amplifiers, Equalizers , and Surround Sound Processors – two (2) year warr anty .
JBL SIS Products Gr oup 8500 Balboa Boule vard Nor thr idge, CA 91329 250 Cross ways P ar k Dr ive W oodbur y , NY 11797 800-336-4JBL Pa rt No . 070-14991 | Rev 2 | 06/03.
デバイスJBL SYNTHESIS SDP-40の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
JBL SYNTHESIS SDP-40をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJBL SYNTHESIS SDP-40の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JBL SYNTHESIS SDP-40の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JBL SYNTHESIS SDP-40で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JBL SYNTHESIS SDP-40を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJBL SYNTHESIS SDP-40の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JBL SYNTHESIS SDP-40に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJBL SYNTHESIS SDP-40デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。