JensenメーカーJiMS-125の使用説明書/サービス説明書
ページ先へ移動 of 18
® DOCKING DIGIT AL MUSIC SYSTEM FOR iPod OWNER'S MANUAL JiMS-125 ® (iPod Not Included) PLEASE READ THIS OPERA TING MANUAL COMPLETEL Y BEFORE OPERA TING THIS UNIT A ND RET AIN THIS BOOKLET FOR F.
® DEAR JENSEN CUSTOMER IMPORTANT SAFETY INSTRUCTIONS COMPLIANCE WITH FCC REGULATIONS PRODUCT FEA TURES INSTALLA TION LOCATION OF CONTROLS CLOCK SETTING ALARM OPERA TIONS RADIO OPERA TIONS iPod DOCKIN.
2 Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers.
3 IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However , improper use can result in potential electrical shock or fire hazards.
4 10.Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire of electric shock. 11.Damage Requiring Service This unit should be serviced by qualified service personnel when: A.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 PRODUCT FEA TURES JiMS-125 is an iPod Docking Music System which incorporates the • iPod , iPod mini, iPod classic, iPod touch and iPod nano Player / Re-charger • AM / FM Stereo receiver with di.
7 INSTALLA TION Clock setting battery back-up The battery back-up compartment is located on the back of the unit. (1) Remove the battery compartment door . (2) Follow the polarity diagram shown inside the compartment and install 2 x AAA batteries (not included) .
8 Main Unit Front view T op view 1 2 3 5 4 6 8 9 12 7 11 10 14 14 13 1. iPod docking station 2. iPod docking connector 3. Function switch : Power Off ; select RADIO / iPOD / AUX modes. 4. Band switch : 5. VOLUME knob : 6. TUNING knob : 7. SNOOZE button : Activate the snooze function.
18. DC-in jack : For the connection of external DC power supply 19. FM Antenna wire 20. Battery Compartment 21. RESET button : Reset the unit. 9 LOCATION OF CONTROLS Remote Control (for iPod only) 1. Infra-red T ransmitter 2. iPod PLAY / P AUSE button 3.
ALARM OPERATIONS Setting Alarm Time 1. With the unit powered of f, press & hold the ALARM SET button to display Alarm time, the alarm indicator flashes on LCD; then press the (HOUR) / (MINUTE) buttons to set the alarm time. 2. After the alarm time is set, release the ALARM SET button.
Wake to Radio Snooze Funtion - Y ou can activate the Snooze function manually after the alarm sounds by pressing the SNOOZE button once. Alarm will sound again in 5 minutes and snooze can be manually activated again within 1 hour - After the alarm sounds you can also press the ALARM ON / OFF button to stop it immediately .
12 RADIO OPERA TIONS Radio Operation extend the FM Antenna wire for the best reception. 1. Slide the FUNCTION switch to RADIO mode. 2. Slide the BAND switch to select FM Stereo / FM or AM band. 3. Rotate the TUNING knob and tune to a desired station. 4.
13 iPod DOCKING If the docking port will not be used for an extended period of time, it is recommended to cover the docking port by using the “Dock Cover” insert (included). 1. Use the iPod adaptor included in your iPod and insert it into the docking area.
The unit provides the auxiliary audio signal input for the connection of an external audio device. You may connect an audio cable with 3.5 mm stereo plug (not included) to the AUX IN Jack located at rear of the unit.
CARE AND MAINTENANCE • Do not subject the unit to excessive force, shock, dust or extreme temperature. • Do not tamper with the unit's internal components. • Clean your unit with a damp (never wet) cloth. Solvents or detergents should never be used.
Symptom Possible Problem Solution The unit does not respond (no power) AC A daptor is not plugged into a wall outlet or the connector is not plugged into the power supply jack on the back of the unit. Plug the A C adaptor into a wall outlet and plug the connector into the supply jack on the unit.
Printed in China SPECIFICATIONS Power Requirement Main unit DC input: DC10V , 1000mA Battery back up for clock: 2 X DC1.5V 'AAA' (UM-4) Batteries Remote Control 1 X CR2032 Lithium Battery Fr.
デバイスJensen JiMS-125の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Jensen JiMS-125をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJensen JiMS-125の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jensen JiMS-125の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jensen JiMS-125で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jensen JiMS-125を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJensen JiMS-125の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jensen JiMS-125に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJensen JiMS-125デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
