John DeereメーカーET-3303-Jの使用説明書/サービス説明書
ページ先へ移動 of 16
3 1/4-Inch Belt Sander Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE BELT SANDER AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.
2 3 1/4-Inch Belt Sander Operator's Manual Congratulations on the purchase of your new Belt Sander! You can be assured your belt sander was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance.
3 1/4-Inch Belt Sander Operator's Manual 3 T able of Content SAFETY .................................................................................................................. 4-9 GENERAL SAFETY RULES ......................................
4 3 1/4-Inch Belt Sander Operator's Manual W ARNI N G W A R N I NG SI N T HE M A NUA LS . W A RN I NG SI N T HE M A NUA LS . CA U T I ON OC A UT I ON S IN O T H E M A N UA L S OC AUT I ON S IN O .
3 1/4-Inch Belt Sander Operator's Manual 5 KEEP WORK AREA CLEAN AND WELL LIT. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT . Don't expose power tools to rain. Don't use power tools in damp or wet locations.
6 3 1/4-Inch Belt Sander Operator's Manual DON'T OVERREACH Keep proper footing and balance at all times. MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories.
3 1/4-Inch Belt Sander Operator's Manual 7 OUTDOOR USE EXTENSION CORDS When tool is used outdoors, use only extension cords intended for use outdoors and so marked. STAY ALERT Watch what you are doing. Use common sense. Do not operate tool when you are tired.
8 3 1/4-Inch Belt Sander Operator's Manual POLARIZED PLUGS To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
3 1/4-Inch Belt Sander Operator's Manual 9 EXTENSION CORD Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
10 3 1/4-Inch Belt Sander Operator's Manual Functional Description MODEL: ET-3303-J 3 1/4-INCH BELT SANDER NAME OF PARTS: (Fig. 1a) (Fig. 1b) NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool.
3 1/4-Inch Belt Sander Operator's Manual 11 Operation APPLICATIONS: - Sanding finish and flooring finish of woodwork products. - Base polishing of Lumber-coated planes. - Sanding finishes of metal surfaces. - Base polishing of metal-coated planes, rust removal, or paint removal to refinishing.
12 3 1/4-Inch Belt Sander Operator's Manual OPERATION: HOW TO USE THE BELT SANDER: 1. How to adjust sanding position: Push switch and turn sanding belt to check position. Adjust sanding belt so that both edges protrude 1/6” - 1/8” (1.6mm-3mm) past edges of pulleys.
3 1/4-Inch Belt Sander Operator's Manual 13 OPERATION (CONTINUED): 6. How to change belt speed: Either high speed or low speed operation can be selected according to the materials or the operating conditions. Selecting sanding belt operating speed can be achieved by shifting the tumbler switch in a specified direction.
14 3 1/4-Inch Belt Sander Operator's Manual MAINTENANCE AND INSPECTION: CAUTION: BE SURE TO SWITCH POWER OFF AND DISCONNECT THE PLUG DURING MAINTENANCE AND INSPECTION. 1. Inspecting the Sanding Belts: If the sanding belt becomes loaded with debris or dull, the efficiency will drop significantly.
3 1/4-Inch Belt Sander Operator's Manual 15 NOTE: Due to JOHN DEERE’s continuing program of research and development, the specifications herein are subject to change without prior notice. SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use.
16 3 1/4-Inch Belt Sander Operator's Manual Manufactured for Deere & Company, Moline, Illinois 61265 3 1/4-Inch Belt Sander Operator's Manual 110 Code No.
デバイスJohn Deere ET-3303-Jの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
John Deere ET-3303-Jをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJohn Deere ET-3303-Jの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。John Deere ET-3303-Jの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。John Deere ET-3303-Jで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
John Deere ET-3303-Jを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJohn Deere ET-3303-Jの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、John Deere ET-3303-Jに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJohn Deere ET-3303-Jデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
