JVCメーカーCA-UXP400の使用説明書/サービス説明書
ページ先へ移動 of 32
MICRO COMPONENT SYSTEM UX-P400 —Consists of CA-UXP400 and SP-UXP400 INSTRUCTIONS GVT0128-003A [B] Cover[B].fm Page 1 Sunday, January 18, 2004 6:58 PM.
G-1 Warnings, Cautions and Others CAUTION—STANDBY/ON button! Disconnect the mains plug to shut the power off completely (all lamps and indications go off). The STANDBY/ON button in any position does not disconnect the mains line. • When the unit is on standby, the STANDBY/ON lamp lights in red.
1 Contents Introduction ........................................................ 2 Precautions .......................................................................... 2 How to Read This Manual .................................................. 2 Getting Started .
2 Introduction Precautions Installation • Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C. • Install the System in a location with adequate ventilation to prevent internal heat buildup inside the System.
3 Getting Started Step 1 : Unpack After unpacking, check to be sure that you have all the following items. The number in parentheses indicates the quantity of each piece supplied. • FM antenna (1) • AM loop antenna (1) • Remote control (1) • Batteries (2) If any item is missing, consult your dealer immediately.
4 Step 3 : Hook Up If you need more detailed information, see page 6. AUX LEFT RIGHT AUDIO OUT Illustrations of the input/output terminals below are typical examples. When you connect other components, refer also to their manuals since the terminal names actually printed on the rear may vary.
5 PUSH OPEN AU TO R EV ER S E FM antenna (supplied) Extend it so that you can obtain the best reception. AM loop antenna (supplied) Turn it until the best reception is obtained.
6 To assemble and connect the AM loop antenna To assemble the AM loop antenna To connect the AM loop antenna • If the AM loop antenna wire or speaker cords are covered with vinyl, remove the vinyl to expose the tip of the antenna by twisting the vinyl.
7 Before Operating the System The indications on the display teach you a lot of things while you are operating the System. Before operating the System, be familiar with when and how the indicator illuminates on the display. 1 Rhythm Ax indicator • Lights when Rhythm Ax is activated.
8 Daily Operations —Playback 1 Turn on the power. The STANDBY/ON lamp on the main unit lights in green. • Without pressing STANDBY/ON , the System turns on by pressing one of the source selecting buttons in the next step. 2 Select the source. Playback automatically starts if the selected source is ready to start.
9 To tune in to a station While FM or AM is selected... Frequency starts changing on the display. When a station (frequency) with sufficient signal strength is tuned in, the frequency stops changing. • When you repeatedly press the button, the frequency changes step by step.
10 To select a track To select a group (MP3 only) Before starting playback... Group number and group name appear. To locate a particular portion While playing a disc, press and hold until the portion you want is reached. To locate a track directly and start play Playing Back a Tape To insert a tape You can play back tapes of types I, II, and IV.
11 Daily Operations —Sound&Other Adjustments Adjusting the Volume You can adjust the volume level from level 0 (VOL MIN) to level 40 (VOL MAX). To drop the volume in a moment Adjusting the Sound To emphasize rhythm feeling—RHYTHM AX This function emphasizes bass attack feeling, and also changes the subwoofer level.
12 Changing the Display Brightness You can dim the display window. Setting the Clock Without setting the built-in clock, you cannot use Daily/ Recording Timers (see page 21) and Sleep Timer. • To exit from the clock setting, press CLOCK/TIMER as required.
13 Advanced Radio Operations Receiving FM Stations with RDS Radio Data System (RDS) allows FM stations to send an additional signal along with their regular program signals. • When tuned to an FM station which provides the RDS service, the RDS indicator lights on the display.
14 3 Start searching. The receiver searches 30 preset FM stations, stops when it finds the one you have selected, and tunes in to that station. • If no program is found, “NOTFOUND” appears on the display. • To stop searching any time during search, press PTY SEARCH.
15 Description of the PTY codes NEWS News. AFFAIRS Topical program expanding or enlarging upon the news—debate, or analysis. INFO Programs the purpose of which is to impart advice in the widest sense. SPORT Programs concerned with any aspect of sports.
16 Advanced Disc Operations Programming the Playing Order— Program Play You can arrange the playing order of the tracks (up to 50) before you start playback. 1 Before starting playback, activate Program Play. 2 Select tracks you want for Program Play.
17 To check the programmed contents Before or after playback... To modify the program Before or after playback... To exit from Program Play Before or after playback... • Exiting from Program Play erases the stored program. Playing at Random—Random Play You can play all tracks at random.
18 Playing Repeatedly—Repeat Play You can repeat playback. Before starting playback... While playing... To repeat a particular portion—A-B Repeat You can repeat a particular portion while playing back a CD. 1 During playback, activate A-B Repeat. 2 Select the start point (A).
19 Advanced Tape Operations Recording on a Tape You can use type I tapes for recording. • To play a tape, see page 10. 1 Insert a recordable cassette. 2 Check the tape running direction and Reverse Mode settings on the display. To change the direction To change the Reverse mode if necessary REV.
20 3 Select and start playing the source—“FM,” “AM,” “CD,” or “AUX.” • When recording a disc, you can also use “Synchronized Disc Recording” (see below). 4 Start recording. Synchronized Disc Recording You can start and stop both disc play and tape recording at the same time.
21 Timer Operations Setting the Timer Using Daily Timer, you can wake up with your favorite song. On the other hand, with Recording Timer, you can make a tape of a radio broadcast automatically.
22 3 Select the volume level. • You can select the volume level ( “ VOLUME 0 ” to “ VOLUME 40 ” and “ VOLUME – –” ). If you select “ VOLUME – – , ” the volume is set to the last level when the unit has been turned off. For Recording Timer: 1 Set the hour then the minute for on-time.
23 To turn off the Timer after its setting is done Since Daily Timer is activated at the same time everyday, you may need to cancel it on some particular days. • Recording Timer can also be canceled temporarily. 1 Select the Timer you want to cancel.
24 Additional Information Learning More about This System Daily Operations—Playback (see pages 8 to 10) Listening to the Radio: • If you store a new station into an occupied preset number, the previously stored station in that number will be erased.
25 Troubleshooting If you are having a problem with your System, check this list for a possible solution before calling for service. General: Adjustments or settings are suddenly canceled before you finish. ] There is a time limit. Repeat the procedure again.
26 Specifications Amplifier section Output Power: 40 W (20 W + 20 W) at 4 Ω (10% THD) Speakers/Impedance: 4 Ω – 16 Ω Audio Input AUX: 400 mV/50 k Ω Tuner section FM tuning range: 87.
SAFETY INSTRUCTIONS “SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
MEMO ME MO . f m Pag e 1 W e d n e sd ay , J an u ar y 21, 2004 6: 03 PM.
MEMO ME MO . f m Pag e 2 W e d n e sd ay , J an u ar y 21, 2004 6: 03 PM.
VICTOR COMPANY OF JAPAN, LIMITED 0104AIMMDWJEM EN © 2004 VICTOR COMPANY OF JAPAN, LIMITED UX-P400 MICRO COMPONENT SYSTEM Cover[B].fm Page 2 Sunday, January 18, 2004 6:58 PM.
デバイスJVC CA-UXP400の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
JVC CA-UXP400をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC CA-UXP400の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC CA-UXP400の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC CA-UXP400で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC CA-UXP400を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC CA-UXP400の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC CA-UXP400に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC CA-UXP400デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
