JVCメーカーGD V500PZUの使用説明書/サービス説明書
ページ先へ移動 of 18
1 INSTRUCTIONS GD-V500PZU PLASMA DISPLA Y MONIT OR For customer Use: Enter below the Model No. and the Serial No. which is located on the rear panel of the cabinet.
3 1) Read these instructions. All the safety and operating instructions should be read bef ore the appliance is operated. 2) K eep these instr uctions. The safety and operating instructions should be retained f or future reference. 3) Heed all warnings.
5 T able of Contents Important Safety Instructions ....................................... 3 FCC ST A TEMENT ........................................................... 6 Safety Precautions ......................................................... 7 Accessories .
7 Safety Precautions W ARNING Set up Do not place the Plasma Display Monitor on sloped or unstable surfaces. • The Plasma Display Monitor ma y fall off or tip over .
9 Accessories Accessories Supplied Optional Accessories PLASMA DISPLAY INPUT SURROUND VOL NR PICTURE SOUND SET UP ASPECT PICTURE POS. /SIZE OFF TIMER PC GD-V500PZU Operating Instruction book Remote Co.
11 Basic Controls R - ST ANDBY G POWER ON INPUT – VOL + Main Power On/Off Switch V olume Adjustment Push the V olume Up “ + ” or Down “–” button to increase or decrease the sound volume level.
13 Connections How to connect the speakers When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speak er ’ s Installation Manual for details on speak er installation. 1 1 2 2 Speakers (Optional accessories) How to connect the A V Input T erminals Connect the signal source equipment (see pages 14 to 17).
15 Connections How to connect the COMPONENT/RGB Input T erminals RGB signal (R, G, B, HD, VD) connection Notes: (1) Change the “ COMPONENT/RGB-IN ” setting in the “ SET UP ” menu to “ Y/PB/PR ” . (see page 30, 32) (2) Additional equipment and cables shown are not supplied with this set.
17 Connections How to connect the SERIAL T erminals SERIAL RS-232C cable D-sub 9p COMPUTER The SERIAL terminal is used when the Plasma Display Monitor is controlled by a computer . 9 8 7 6 5 3 2 14 Pin layout for RS-232C Communication parameters Notes: (1) Use the RS-232C cable to connect the computer to the Plasma Displa y Monitor.
19 Select the Input Signal R - STANDBY G POWER ON INPUT — VOL + — VOL + INPUT Press the INPUT button to select the input video signal desired from equipment such as a VCR which has been connected to the Plasma Display Monitor .
21 On-Screen Menu Display from Remote Control Selecting the On-Screen Menu Language Press to select OSD LANGUAGE. Press to select your preferred language. Selectable languages English (UK) Deutsch Fran ç ais Italiano Espa ñ ol ENGLISH (US) T o SOUND adjust menu (see page 26) T o SET UP menu (see page 30) SET UP Press to display the SET UP menu.
23 ASPECT Controls Mode NORMAL ZOOM FULL JUST AU TO Explanation NORMAL will display a 4:3 picture at its standard 4:3 size. ZOOM mode magnifies the central section of the picture. FULL will display the picture at its maximum size but with sight elongation.
25 Adjusting PICTURE POS./SIZE H-POS H-SIZE V -POS V -SIZE CLOCK PHASE (RGB/PC in Mode) When the Position Right “ ” button is pressed When the Position Right “ ” button is pressed When the Pos.
27 SURROUND Controls SURROUND Button The benefits of surround sound are enormous. Y ou can be completely enveloped in sound; just as if you were at a concert hall or cinema. The surround setting switches on and off each time the SURROUND button is pressed.
29 Note: There is little change when PICTURE is increased with a bright picture or reduced with a dark picture. PICTURE Adjustments Item PICTURE BRIGHTNESS COLOR TINT (NTSC only) SHARPNESS Effect Adjustments Less More Darker Brighter Reddish Greenish Selects the proper brightness and density for the room.
31 SET UP for Input Signals COLOR SYSTEM / A UTO Select SIGNAL from the “ SET UP ” menu during VIDEO (S-VIDEO) input signal mode. ( “ SIGNAL [VIDEO] ” menu is displayed.
33 T roubleshooting Before you call f or service, determine the symptoms and make a few simple chec ks as shown below. Symptoms Checks Electrical Appliances Cars/Motorcycles Fluorescent light V olume (Check whether the mute function has been activated on the remote control.
35 GD-V500PZU EUR646526 2 × AA Size TS-C5000SPG TS-C50P1G TS-C50P6G TS-C50P2G TS-C50P3G 47.6 ” (1210mm) × 28.5 ” (724 mm) × 3.9 ” (98mm) approx.
デバイスJVC GD V500PZUの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
JVC GD V500PZUをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC GD V500PZUの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC GD V500PZUの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC GD V500PZUで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC GD V500PZUを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC GD V500PZUの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC GD V500PZUに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC GD V500PZUデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
