JVCメーカーHD-52Z575の使用説明書/サービス説明書
ページ先へ移動 of 37
SERVICE MANUAL COPYRIGHT © 2004 Victor Company of Japan, Limited. No.YA092B 2004/8 REAR PROJECTION TELEVISION 52096 2003 02 HD-52Z575, HD-52Z585, HD-61Z575, HD-61Z585 T A B L E O F C O N T E N T S 1 PRECAUTIONS . . . . . . . . . . . . . . . . . . . .
1-2 (No.YA092B) SPECIFICATION Design & specification s are subject to cha nge without notice. Items Contents HD-52Z575 HD-52Z585 HD-61Z575 HD-61Z585 Dimensions (W x H x D) 126.4cm x 91.4cm x 41.2cm (49-7/8" x 36 x 16 -1/4") 145.6cm x 104.
(No.YA092B)1-3 SECTION 1 PRECAUTIONS 1.1 SAFETY PRECAUTIONS (1) The design of this product contains spe cial hardware , many circuits and components specia lly for safety purp oses. For contin ued protection, no ch anges should be m ade to the orig inal design unless authorized in writing by th e manufacturer.
1-4 (No.YA092B) 1.2 INSTALLATION 1.2.1 HEAT DISSIPATION If the heat dissipation vent be hind this unit is blocked , cooling efficiency may deteriorate and temperature inside the unit will rise.
(No.YA092B)1-5 1.3 LAMP UNIT HANDLING CAUTION 1.3.1 PRECAUTION FOR LAMP UNIT The lamp em its high i ntensity white, ultra violet a nd infrared light. Do not lo ok directly at the li ght during service. Also, do not touch the lamp directly as it pres ents a burn hazard.
1-6 (No.YA092B) 1.4 SERVICE PARTS KIT INSTRUCTIONS Due to the cha racter of this product, these OPTICAL / DRIVE ASS’Y are prepared. Please note these OPTICAL /DRIVE A SS’Y when replacing or ordering the parts . 1.4.1 PART NUMBER AND CONSTRUCTION 1.
(No.YA092B)1-7 SECTION 2 SPECIFIC SERVICE INSTRUCTIONS 2.1 TECHNICAL INFORMATION 2.1.1 DIFFERENCE LIST 2.1.2 PROJECTION UNIT 2.1.3 IMAGE LIGHT F LOW 2.
1-8 (No.YA092B) 2.1.6 MAIN CPU PIN FUNCTION (IC7601 : M306V7FGF-088FP) [DIGITAL SIGNAL PWB ASS’Y] Pin Port Pin name I/O Function 1 VHOLD1 VHOLD1 I Data slice for main screen closed caption 2 HFLT1 HFLT1 I/O LPF for main screen close d caption video input 3 P9.
(No.YA092B)1-9 2.1.7 SUB (CHASSIS) CPU PIN F UNCTION (IC7001 : MN102H60KPA) [DIGITAL SIGNAL PWB ASS’Y] Pin Port Pin name I/O Function 1 P60 LB PRO O Not use 2 P61 P MU O Picture muting [Muting = H] .
1-10 (No.YA092B) 2.1.8 SYS T EM RESET When the DIGITAL SIGNAL P W B is r e plac e d or the DIGI T A L INPUT is not nor m al, reset the S Y STEM SETTING using the following proc e dure. (1) S et to 0 minutes u s i ng the [S L E EP T I MER] key. (2) Press the [VIDEO STATUS ] key and [DISPLAY] key simu l t a neo u sly to e n t e r the SERVICE MODE.
(No.YA092B)1-11 SECTION 3 DISASSEMBLY 3.1 DISASSEMBLY PROCEDURE • Make sure that the power cord plug is pull out fro m the AC wall outlet. • Wait until the LAMP UNIT has cool down is completely. • Whil e not in repair service, place the chassis back its origin al position.
1-12 (No.YA092B) FRONT CENTER PANEL LAMP COVER LAMP UNIT FRONT LED PWB SPEAKER GRILL(R) CUSHION SPEAKER FRONT PANEL SPEAKER GRILL(L) FILTER COVER SCREEN BRACKET SCREEN BLOCK SCREEN ASSY FRONT CABINET .
(No.YA092B)1-13 <FRONT INNER SIDE> 3.1.11 MIRROR • Take out the SPEAKER GRILL both side. • Take ou t the FRONT PANEL. • T ake out the SCREEN BLOCK. (1) Remove 12 screws [ A ] attaching the MIRROR HOLDER of the upper, left and right side. (2) Raise slightly to disenga ge of the MIRROR from the bottom holder.
1-14 (No.YA092B) <BODY SIDE> 3.1.15 BODY COVER (1) Remove 9 screws [ A ] (BODY). (2) Remove 6 screws [ B ] (AV TERMINAL BOARD). (3) Take out the BODY COVER. NOTE : • Do not leave the BODY COVER remove d for long time to prevent soiling from dust.
(No.YA092B)1-15 <INNER PWB SIDE> 3.1.18 AV TERMINAL BOARD • Take ou t the BODY COVER. (1) Remove 5 screws [ A ] . (2) Remove 1 screw [ B ] . (3) Pull out t he POWER CORD CLAMP. (4) Remove the nut [ C ] attaching the ANTENNA TERMINAL. (5) Take out the AV TERMINAL BOARD.
1-16 (No.YA092B) FRONT POWER CORD POWER PWB POWER PWB BRACKET UNIT BASE DIGITAL SIGNAL PWB REGULATOR PWB ANALOG PWB BRACKET ANALOG SIGNAL PWB RECEIVER PWB SUB DRIVE PWB PWB HOLDER REAR JACK PWB ANTENN.
(No.YA092B)1-17 <OPTICAL SIDE> 3.1.26 LAMP FAN DUCT & THERMOSTAT • Take ou t the BODY COVER. • Take ou t the BODY BRACKET. • Take ou t the MAIN UNIT. (1) Remove 4 screws [ A ] . (2) Take out the LAMP FAN DUCT. (3) Remove 2 screws [ B ] .
1-18 (No.YA092B) <OPTICAL SIDE VIEW> FRONT FRONT FRONT OPTICAL / DRIVE ASS'Y THERMOSTAT LAMP FAN DUCT LAMP FAN BRACKET ASSY LAMP UNIT BODY LAMP BALLAST UNIT BALLAST COVER BALLAST BRACKET TO.
(No.YA092B)1-19 3.1.36 SHIELD PLATE ATTACHMENT PROCESS • Take ou t the TOP DUCT / TOP DUCT PLATE. • Take ou t the MAIN DRIVE PW B with SHIELD TOP CASE. < Assembly > (1) Copper film case with laminate surfa ce to be top. (2) Fold 9 points as shown in [ A ] an arrow vi ew Fig.
1-20 (No.YA092B) 3.2 MEMORY IC REPLACEMENT 3.2.1 MEMORY IC This memory IC stores data for proper operation of the video and Drive circuits. When replacing, be sure to use an IC containing this (initial value) data. 3.2.2 MEMORY IC REPLACEMENT PROCEDURE 1.
(No.YA092B)1-21 3.2.4 SETTING OF FA CTORY SHIPMENT 3.2.4.1 BUTTON OPERATION 3.2.4.2 REMOTE CONTRO L DIRECT OPER ATION 3.2.4.3 REMOTE CONT ROL MENU OPERATION (1) PICTURE ADJ UST[ 1 ] (5) INITIAL SETUP .
1-22 (No.YA092B) 3.3 REPLACEMENT OF CHIP COMPONENT 3.3.1 CAUTIONS (1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reus e a chip part afte r removing it.
(No.YA092B)1-23 SECTION 4 ADJUSTMENTS 4.1 ADJUSTMENT PREPARATION (1) You can ma ke the necessary adjus tments for this un it with either the remote co ntrol unit or with the adjustment equi pment and parts as given below.
1-24 (No.YA092B) 4.5 BASIC OPERATION OF THE SERVICE MENU Operate the SERVICE MENU wit h the remote control unit. 4.5.1 HOW TO ENTER THE SERVICE MENU (1) Press the [SLEEP TIMER] key and while indication of "SLEEP TIMER 0 MIN." is being displayed, press [DISPLAY] key and [VIDEO STATUS] key simultaneously, and the SERVICE MENU screen of Fig.
(No.YA092B)1-25 4.5.7 DESCRIPTION OF STATUS DISPLAY The status display on the upp er part of the SERVICE MENU screen is common. (1) SIGNAL SYSTEM (2) ASPECT (3) VIDEO STATUS (4) WHITE BALANCE 4.5.8 SETTING OF THE SERVICE MENUS 4.5.8.1 [1.ADJUST] Do not change settings of items that are not included in the "A DJ USTMENT PROCEDURE".
1-26 (No.YA092B) 4.6 INITIAL SETTING VALUE OF SERVICE MENU (1) Adjustment of the SERVICE MENU is made on the basis of the initial setting values; ho wever, the new setting values which set the screen in its optimum condition may differ from the initial setting.
(No.YA092B)1-27 Item No. Item name Variab le range Setting value D012 SV GN 0~ 3F 00 D013 SVH GN 0~3F 00 D014 SH GN 0~3F 00 D015 SV Pf 0~03 00 D016 SV Pf H 0~01 00 D017 SV Pf L 0~03 00 D018 SYL CON 0~.
1-28 (No.YA092B) Item No. Item name Variab le range Setting value D108 (NO DISPLA Y) 0~FF 00 D109 (NO DISPLA Y) 0~FF 00 D1 10 (NO DISPLA Y) 0~FF 00 D 111 ( N O D I S P L AY ) 0 ~ F F 0 0 D1 12 (NO DIS.
(No.YA092B)1-29 4.7 ADJUSTMENT PROCEDURE 4.7.1 OPTICAL BLOC K / DRIVE CIRCUIT Item Measuring instrument Test point Adjustment part Description LENS FOCUS adjustment Hexagon wrench FOCUS knob [PROJECTION LENS] (1) T ake out the FRON T P ANEL, SPEAKER GRILL (L / R), CENTER P ANEL and cushions.
1-30 (No.YA092B) Item Measuring instrument Test point Adjustment part Description DRIVE CENTER POSITION adjustment Signal generator Remote control unit (1) Input the center-cross signal pattern. (2) Set the [SLEEP TIMER] to 0 min. (3) Press the [DISPLA Y] key and the [VIDEO ST A TUS] key simultaneously .
(No.YA092B)1-31 4.7.2 VIDEO CIRCUIT Item Measuring instrument Test point Adjustment part Description 525i A-D OFFSET adjustment Signal generator Remote control unit [1. ADJUST] S001: PREP ARE S008: 5i CB OF (525i Cb offset) S009: 5i CR OF (525i Cr offset) (1) Input a 525i ramp pattern from COMPONENT VIDEO INPUT terminal.
1-32 (No.YA092B) Item Measuring instrument Test point Ad justment part Description 1 125i A-D OFFSET adjustment Signal generator Remote control unit [1.
(No.YA092B)1-33 4.7.3 MTS CIRUT Item Measuring instrument Test point Adjustment part D escription WHITE BALANCE (High light) adjustment Signal generator Remote control unit [1. ADJUST] S030:R DRIVE (Red drive) S031:G DRIVE (Green drive) S032:B DRIVE (Blue drive) (1) Receive a NTSC all-white (75% white) pattern signal.
1-34 (No.YA092B) SECTION 5 TROUBLESHOOTING 5.1 SELF-CHECK FEA TURE 5.1.1 OUTLINE This unit comes with the SELF- CHECK feature, which checks the operational state of the circ uit and displays/saves it during failure. SELF-CHECK is performed when power is turned on, and information input to the main microcomputer is monitored at all time.
(No.YA092B)1-35 5.1.6 DET AILS Self-check is performed for the following items. Check item Display Descrip tion of detection Diagnosis signal (line) Means of detection Low bias line sh ort protection LOB Low bias li ne (9V / 5V) short protector activate d.
1-36 (No.YA092B) 5.1.7 DISPLAY METHOD WHEN RASTER IS NOT AVAILABLE In a state where a display screen does not appear due to the failure of this unit, the POWER L ED (blue) and LAMP LED (orange) c an light up and display a trouble mo de.
(No.YA092B) WPC Printed in Japan JVC SERVICE & ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP. www.jvcservice.com(US Only) JVC CANADA INC.
デバイスJVC HD-52Z575の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
JVC HD-52Z575をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC HD-52Z575の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC HD-52Z575の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC HD-52Z575で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC HD-52Z575を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC HD-52Z575の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC HD-52Z575に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC HD-52Z575デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
