JVCメーカーHR-J765EKの使用説明書/サービス説明書
ページ先へ移動 of 48
H R-J765EK VIDEO CASSETTE RECORDER INSTRUCTIONS LPT0168-001A PAL T V P R O G + T V P R O G – T V – T V + TV 0000 START DEBUT STOP FIN DATE MENU OK TV PROG TV/VCR DAILY/QTDN.
2 SAFETY FIRST IMPORT ANT ■ Please read the various precautions on p. 2 – 3 of this instruction manual before installing or operating the recorder .
3 This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment.
4 QUICK SET UP GUIDE T V P R O G + T V P R O G – T V – T V + TV 0000 START DEBUT STOP FIN DATE MENU OK TV PROG TV/VCR DAILY/QTDN. VPS/PDC AUX ? WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 123 4.
5 ENTREE ANT. IN ENTREE/DECODEUR IN/DECODER AV2 ENTREE/SORTIE IN/OUT SORTIE RF OUT ANTENNE AV1 SORTIE OUT R L AUDIO A V CONNECTION T o Connect T o A TV W ith 21-pin A V input connector (SCART) . . . 1– Connect the aerial, recorder and TV as per “RF CONNECTION”.
6 123 456 7 89 0 2 4 1 3 ? STANDBY/ON TIMER REC LINK TV PROG VIDEO ( MONO ) L –AUDIO– R REW FF TV PROG/ JOG SHUTTLE QUICK SET UP GUIDE (cont.) STEP 3 AUTO SET UP SET THE TUNER CHANNELS, CLOCK, GUI.
7 IMPORT ANT ■ In certain reception conditions, station names may not be stored correctly , and auto Guide Program Number Set may not work properly . If the Guide Program numbers are not set properly , when you timer -record a TV programme using VIDEO Plus+, the recorder will record a TV programme of a different station.
8 INFORMA TION When using the A V connection ( ☞ pg. 5), initiating playback causes the VCR indicator to light and the TV to automatically enter A V mode. T o return the TV to TV mode after playback is complete, press TV/VCR so that the VCR indicator turns off.
9 Still Picture/Frame-By-Frame Playback P AUSE DURING PLA YBACK 1 Press P AUSE. If there is vertical jitter , use the TV PROG buttons to correct the picture. ACTIV A TE FRAME-BY -FRAME PLA YBACK 2 T urn the JOG dial to the right for forward frame-by- frame playback, or to the left for reverse frame-by-frame playback.
10 TV signals being received by the recorder ’ s built-in tuner can be recorded onto a video tape. Y ou can “capture” a TV programme using your video recorder . BASIC OPERA TIONS (cont.) Recording T urn on the TV and select the VIDEO channel (or A V mode).
11 Record One Pr ogramme While W atching Another 123 456 7 89 0 2 4 1 3 ? STANDBY/ON TIMER REC LINK TV PROG VIDEO ( MONO ) L –AUDIO– R REW FF TV PROG/ JOG SHUTTLE Elapsed Recording Time Indication Y ou can check the exact time of a recording.
12 ACCESS VIDEO PLUS+ SCREEN 1 Press PROG . The front display panel looks like this: ENTER PLUSCODE NUMBER 2 Press the NUMBER keys to enter the PlusCode number of the programme you wish to record. ● If you make a mistake, press and input the correct number .
13 SET T APE SPEED 4 Press SP/LP ( ) to set the tape speed. SET PDC MODE 5 Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ PDC" is lit on the display panel, PDC is set to ON.
14 123 456 7 89 0 2 4 1 3 ? OK WEEKLY 7 9 DAILY 6 Express Timer Pr ogramming BASIC OPERA TIONS (cont.) If you don’t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder to timer -record the programme.
15 ENTER PRESET POSITION 6 Press TV PROG +/– to enter the preset position corresponding to the broadcasting station you wish to record. SET T APE SPEED 7 Press SP/LP ( ) to set the tape speed. SET PDC MODE 8 Press PDC to select "ON" or "OFF".
16 BASIC OPERA TIONS (cont.) Check, Cancel And Replace Pr ogrammes DISENGAGE TIMER MODE 1 Press , then press . ACCESS PROGRAMME CHECK SCREEN/DISPLA Y 2 Press . ACCESS PROGRAMME SCREEN/DISPLA Y 3 Press again to check more information. Each time you press , the next programme's information appears.
17 0 4 1 3 ? TV PROG ADV ANCED OPERA TIONS Manual T racking Y our video recorder is equipped with automatic tracking control. For most tapes this will automatically adjust the tracking to suit the particular tape you are playing. In some circumstances it may be necessary to make manual tracking adjustments.
18 ADV ANCED OPERA TIONS (cont.) Playback/ Recording According T o T ape Charac- teristics The B.E.S.T . (Biconditional Equalised Signal T racking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures.
19 Recording ST ART RECORDING 1 Press and hold RECORD and press PLA Y on the remote, or press RECORD on the recorder . DURING B.E.S.T . B.E.S.T . COMPLETE ● The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.
20 Soundtrack Selection Y our video recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.
21 Instant ReV iew Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer -recorded programme. If you have several programmes recorded, you can easily access any of them. NOTE: Before starting, make sure that the recorder is off and that the T imer mode is disengaged.
22 This facility allows you to record automatically a satellite programme which is timer -programmed on your external satellite receiver . Connect a satellite receiver to the recorder's A V2 IN/D.
23 A TTENTION ● Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.
24 123 456 7 89 0 2 4 1 3 ? ADV ANCED OPERA TIONS (cont.) Edit T o Or Fr om Another V ideo Recorder Y ou can use your video recorder as the source player or as the recording deck. MAKE CONNECTIONS 1 Connect the player ’ s 21-pin SCAR T connector to the recorder ’ s 21-pin SCAR T connector as illustrated on the below .
25 123 456 7 89 0 2 4 1 3 ? Edit Fr om A Camcorder TV PROG Y ou can use a camcorder as the source player and your video recorder as the recorder . MAKE CONNECTIONS 1 Connect the camcorder’s AUDIO/VIDEO OUT connectors to the recorder ’ s front panel AUDIO/VIDEO input connectors.
26 T urn on the TV and select the VIDEO channel (or A V mode). ADV ANCED OPERA TIONS (cont.) On-Screen Display NOTES: ● When you use this recorder as the player for editing, be sure to set "O.
27 Auto Timer When the Auto T imer is set to ON the timer is automatically engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on. ACCESS MAIN MENU SCREEN 1 Press MENU . ACCESS MODE SET SCREEN 2 Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or # .
28 Repeat Playback Y our video recorder can automatically play back the whole tape 50 times repeatedly . ST ART PLA YBACK 1 Press PLA Y . ACTIV A TE REPEA T PLA YBACK 2 Press PLA Y and hold for over 5 seconds, then release. ● The Play indicator ( ) on the display panel blinks slowly .
29 ENTREE ANT. IN ENTREE/DECODEUR IN/DECODER AV2 ENTREE/SORTIE IN/OUT SORTIE RF OUT ANTENNE AV1 SORTIE OUT R L AUDIO I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I.
30 SUBSIDIARY SETTINGS V ideo Channel Set V ideo Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. With A V Connection ACCESS VIDEO CHAN- NEL SET MODE 1 Press and hold down STOP on the recorder until the display panel shows the following.
31 Before performing the following procedure, make sure that: ■ the mains power cord is plugged into the mains outlet. ■ the video recorder is turned off and there is no cassette inserted in the recorder . ■ the connected TV is turned on. ■ batteries have been installed in the remote control.
32 123 456 7 89 0 2 4 1 3 ? SUBSIDIARY SETTINGS (cont.) T uner Set IMPORT ANT Perform the following steps only if — — Auto Channel Set has not been set correctly by Auto Set Up function ( ☞ pg. 6). — you have moved to a different area or if a new station starts broadcasting in your area.
33 VIEW CONFIRMA TION SCREEN 4 After "SCAN COMPLETED" is displayed on the screen for about 5 seconds, a Confirmation screen looking like the one on the right appears. The stations your recorder located appear on a Confirmation screen — preset positions (PR), channels (CH) and station names (ID – ☞ pg.
34 SUBSIDIARY SETTINGS (cont.) Storing Channels Manually T o s tore channels that were not stored during Auto Set Up ( ☞ pg. 6) or Auto Channel Set ( ☞ pg. 32). ACCESS MAIN MENU SCREEN 1 Press MENU . ACCESS CONFIRMA TION SCREEN 2 Press %fi to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK or # .
35 Perform steps 1 and 2 of "Storing Channels Manually" on page 34 to access the C onfirmation screen before continuing. Change Station Preset Position SELECT ITEM 1 Press % fi @ # until the item you want to move begins blinking. Then press OK and the station name (ID) and its channel (CH) number begin blinking.
36 SUBSIDIARY SETTINGS (cont.) SELECT ST A TION NAME CHARACTER 1 Press # until the first letter of the station name begins blinking. ENTER NEW CHARACTER 2 Press %fi to cycle through the characters (A–Z, 0–9, –, * , +, (space) ) and stop when the desired character is indicated, then press # to enter .
37 TV Station And ID List ST A TION NAME ID* Anglia TV ANGL ARD ARD AR TE AR TE BBC Group BBC BBC1 BBC1 BBC2 BBC2 Berlin 1 BLN1 Berlin 2 BLN2 Border TV BORD Bayern1 BR1 Bayern3 BR3 BR T1 BR T1 BR T2 B.
38 SUBSIDIARY SETTINGS (cont.) TV Station Channel Number Guide Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV . BBC1 BBC2 ITV CH4 CH5 London & South-East Bluebell Hill .
39 Just Clock The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. The Just Clock option can be set "ON" or "OFF" at the Clock Set screen (the default setting is "ON").
40 VIDEO Plus+ Setup SUBSIDIARY SETTINGS (cont.) IMPORT ANT Normally , Auto Set Up ( ☞ pg. 6) or Auto Channel Set ( ☞ pg. 32) sets the Guide Program Numbers automatically . Y ou need to set the Guide Program Numbers manually only in the following cases.
41 PLA YBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect the heads.
42 SUBSIDIARY INFORMA TION (cont.) Before requesting service for a problem, use this chart to see if you can correct the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair .
43 CORRECTIVE ACTION Re-perform the clock and/or timer settings. Press and confirm that “ “ is displayed on the display panel. T imer programming can’t be performed while a timer recording is in progress. W ait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape.
44 FRONT VIEW SUBSIDIARY INFORMA TION (cont.) STANDBY/ON TIMER REC LINK TV PROG VIDEO ( MONO ) L –AUDIO– R REW FF TV PROG/ JOG SHUTTLE 1 2 3 @ $ # 0 7 9 8 4 5 6 & ! ^ % 1 ST ANDBY/ON Button turns recorder on/off (loading a cassette also turns power on).
45 5 AUDIO OUT (L/R) Connectors enable connection of audio cassette recorder , TV or second video recorder for dubbing. ☞ pg. 29 6 RF . OUT Connector enables connection to aerial terminal of TV receiver . ☞ pg. 5 1 Mains Power Cord supplies power to recorder .
46 REMOTE CONTROL 1 TV Button enables remote control of your JVC TV . ☞ "Operating JVC TVs" on pg. 47 2 TV/VCR Button switches connected TV's mode between TV and A V . ☞ pg. 8, 10 and "Operat- ing JVC TVs" on pg. 47 3 REVIEW Button "reviews" timer -recorded programme.
47 ) WEEKL Y Button enables timer recording of weekly serials. ☞ pg. 13, 15 q AUX Button selects recorder's auxiliary input mode. ☞ pg. 24 w Button engages timer -standby mode. ☞ pg. 13, 15 e DA TE +/– Button inputs date of programme for timer recording.
GENERAL Power requirement : AC 220 – 240 V , 50/60 Hz Power consumption Power on : 20 W Power off : 4.5 W T emperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 400 x 94 x 281 mm W eight : 3.
デバイスJVC HR-J765EKの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
JVC HR-J765EKをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC HR-J765EKの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC HR-J765EKの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC HR-J765EKで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC HR-J765EKを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC HR-J765EKの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC HR-J765EKに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC HR-J765EKデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
