JVCメーカーIntegrated Digital Wide LCD Panel TV LT-20DA6SSPの使用説明書/サービス説明書
ページ先へ移動 of 44
INSTRUCTIONS ENGLISH L T -20DA6SSP INTEGRA TED DIGIT AL WIDE LCD P ANEL TV D igital ideo roadcasting V B DV B Trade Mark of the DVB Digital V ideo Broadcasting Project (1991 to 1996) Number: 4138 ©20.
- 1 - i Contents PC Picture Position Menu ................... 3 4 PC Picture Menu ................................. 3 4 Sound Menu ........................................ 3 5 PIP Picture ........................................... 3 5 Source Menu ...
- 2 - For your safety This equipment has been designed and manufactured to meet international safety stan- dards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. So, please read the points below for your own safety .
- 3 - DONT continue to operate the equipment if you are in any doubt about it working normally , or it is damaged in any way switch off, with- draw the mains plug and consult your dealer. DONT put the empty batteries into garbage instead of recycle bin to reduce harmfull ef- fects to the environment.
- 4 - W ARNING Fingers may be trapped under the TV causing injuries. Hold the TV at the bottom in the middle, and do not al- low it to tilt up or down. The TV may fall causing injuries. Hold the bottom of the stand with your hand and tilt the TV up and down.
- 5 - Where to install W ARNING When you install the TV on the wall, only use a JVC wall mounting unit which is designed for this TV . Make sure the TV is inst alled on the wall by a skilled inst aller . Locate the TV away from direct sunlight and strong lights, soft, indirect lighting is recommended for comfortable viewing.
- 6 - Import ant Information Please take note EXCLUSION CLAUSE JVC shall under no circumstances be liable for loss and/or damage to the product caused by: fire; earthquake; accidental dama.
- 7 - Control Panel Buttons With certain combinations of connectors and leads the back cover may not be easily fitted. If the cover is left off, this in no way infringes safety requirements. 01-ENG-20710W-17MB16P-C1897S UK-(LT-20DA6SSP)-(TVAVOK)-IDTV-10042117-5008XXXX.
- 8 - Using the stand This TV comes with a T able T op St and already attached. This stand can be used to adjust the direction of the TV screen 10° backward and 5° forward. Tilt the TV up and down: While holding the bottom of the stand with one hand, use your other hand to hold the middle of the top of the TV and slowly tilt the TV up and down.
- 9 - Remote Control Buttons 3 79 $9 /.
- 10 - Features It is a remote controlled Integrated Digital colour television and PC monitor . 100 programmes from VHF , UHF bands or cable channels can be preset. It can tune cable channels. Controlling the TV is very easy by its menu driven system.
- 11 - Getting Started Follow Step 1 to 7 to set up your TV: Step 1: Checking the accessories supplied Remote control unit x 1 AA/R6 battery x 2 AC adapter x 1 Power cord x 1 Step 2: Inserting batteries Remove the battery cover located on the back of the remote control by gently pulling upwards from the indicated part.
- 12 - 100 mm mount based on VESA regulation is equipped. The handle and the stand can be left by loosing the screws with a screwdriver when mounting the TV on a wall. S pread a soft cloth on a flat t able and then place the TV on the cloth with the screen facing downwards when you leave the handle and the stand.
- 13 - IMPORT ANT : Only use the adaptor supplied with this TV . The TV set is designed to operate on 24 V DC. For this, an adaptor is used which gives 24 V DC voltage.
- 14 - Step 6: Switching the TV ON/OFF T o switch the TV on Y our TV will switch on by two steps: 1- Connect the power supply cord to the sys- tem. Then the TV switches itself to stand- by mode and the power lamp becomes red located on the front of the TV .
- 15 - T o cancel APS before starting, press BLUE button. First of all choose the Language which the menus of the analogue part of the TV will ap- pear . As soon as you change the language, the menu items will be displayed in the se- lected language.
- 16 - number buttons) during recording, a message appears asking if you want to stop recording or not. Press OK button to stop recording or BLUE button to continue recording. Do not turn the TV off in the following cases: When recording images from an external device connected to TV (For example camcorder).
- 17 - Operating while watching IDTV Pressing the TV/DTV button at any time while watching television programmes will switch the TV set between displaying the digital ter- restrial television broadcasting and its nor- mal analogue broadcasting. It is also used to switch to the last watched mode (TV or DIGIT AL TV) from the E XT mode.
- 18 - M Current date and time N Channel listings O Selected date and time P Programme name and broadcast time Q Brief description of the programme The programme name, broadcast time and a brief description of the programme are displayed for the programme chosen from the channel listings.
- 19 - Timers (DTV Timer Recording) By setting the timer, you can record a Digit al terrestrial broadcasting (DVB-T) programme with a VCR connected to EXT -2 while you are out. Before using DTV timer recording, the VCR and TV must be connected correctly .
- 20 - Press the button. End: Set the timer end time with the number but- tons. When the / buttons are pressed, the input position moves. Press the button. Date: Set the date for the timer to work with the num- bers.
- 21 - Reactivating the cancelled timer setting Display the TIMER MENU and press the / buttons to choose which timer setting to reactivate. Press the / buttons so that Active appears in the Mode column. Configuration Set the basic setting when watching Digital terrestrial broadcasting (DVB-T).
- 22 - Off: The Edit PR List Favourites settings are dis- abled. When the / button is pressed, all the channels registered in the Edit PR List can be chosen. Parental Settings Some channels broadcast material which you do not want younger members of the family to watch.
- 23 - The Edit PR List can be used to do the follow- ing: delete registered channels edit channel names. lock channels so that they can not be watched by children. set Favourites so that you can easily choose from only the channels you often watch.
- 24 - If you have not changed the PIN code in the CONFIGURA TION menus Enter PIN Code ( see page 22 ), input the PIN code you chose. The lock icon appears next to the channel name in the Edit PR List. When a locked channel is chosen, the En- ter PIN code input window will appear .
- 25 - When OK button is pressed, following mes- sage will appear on the right bottom side of the screen: Manual Search: This is for searching for digital channels on a single broadcast frequency .
- 26 - When no module is inserted, No CI Mod- ule appears. Refer to the module instruction manual for details of the settings. Setting The TV Menu System Y our TVs analogue part has been designed with a menu system to provide an easy ma- nipulation of a multi-function system.
- 27 - Setting Sharpness Using or button select Sharpness. Press button to increase sharpness level. Press button to decrease sharpness level. Setting Colour Using or button select Colour .
- 28 - Sound Menu As you enter the main menu, sound will be the second item. In the main menu, select Sound using or button, then enter the sound menu by pressing / or OK button. Setting V olume As you enter the sound menu, Volume will be the first selected option.
- 29 - T o Store The Settings In the Sound Menu, all settings are stored automatically . Feature Menu Press MENU button, now you are in mainmenu. In the main menu, select Feature using or button. Then enter the Fea- ture menu by pressing / or OK but- ton.
- 30 - Selecting Band Band, can be chosen either, C or S by or button. Selecting Channel Channel can be changed by or button or by Digit Buttons. Selecting Colour System Using or button on Colour System , you can change the colour system to P AL, SECAM or Auto .
- 31 - T o choose a channel in the PROGRAM menu Press / / / button. The programme number that you choose is high- lighted in the Program. Caution: Using Delete or Insert function rewrite the current chan- nel list in the Program menu.
- 32 - Other Features TV Status Programme Number , Programme Name (or EXT ), (they are displayed on the upper left of the screen). The sound indicator is displayed with them too. They are displayed after programme change for 3 seconds. Sound Indicator The alternatives of the indicator are Mono, S te- reo, Dual I and Dual II.
- 33 - Zoom Modes Zoom mode can be changed by pressing ZOOM button. Y ou can change the screen size according to the picture aspect ratio. Select the optimum one from the following ZOOM modes.
- 34 - Use a D-SUB cable to connect the TVs PC input to the computers RGB output termi- nal. If you want to listen to the sound from the computer , use an audio cable to connect the PC AUDIO IN to the computer s sound output terminal.
- 35 - Sound Menu In the main menu select Sound using or button then enter the Sound menu by pressing / or OK buttons.
- 36 - In PC Mode, if the resolution and the vertical frequency is not supported by the concept, it is displayed an OSD message: Signal out of range Analogue T eletext T eletext is an information system that displays text on your TV screen.
- 37 - Select the required subcode page number by pressing four digit buttons (e.g. 0001). If the selected subcode page is not displayed in a short time, press button. TV programme will be displayed on the screen. T eletext page number will be displayed on the upper left corner of the screen when the selected page is found.
- 38 - If you have a device which outputs component video (Y/Pb/Pr), connect it to the EXT -3 termi- nal with a component video cable and an au- dio cable. Via the ANT (aerial) socket If your equipment does not have an Eurocon- nector or RCA jacks, connect it to the TV with an aerial cable.
- 39 - Peripheral Equipment Connections 3& $ 8', 2,1 $17 (11$ (;7 $ % & ' ( (;7 ) * + , '&,1 3&,13 87 (;7 (;7 $8',2.
- 40 - Peripheral Equipment Connections DECODER FOR SA TELLITE RECEIVER VIDEO HEADPHONE AUDIO Antenna Connections 2XWGRR U $QWH QQD&R QQ HFWLRQ V 01-ENG-20710W-17MB16P-C1897S UK-(LT-20DA6SSP)-(TVAVOK)-IDTV-10042117-5008XXXX.
- 41 - PC Input T ypical Display Modes The display has a maximum resolution of 1360x768 , vertical sync. frequency range of 50-75 Hz and a horizontal sync. frequency range of 30-69 KHz. The following table is an illustration of some of the typical video display modes.
- 42 - PC Picture If no PC picture appears, check that the D- SUB cable is connected properly . Check that your PCs resolution set correctly . See pages 41 for supported modes.
- 43 - Specifications Broadcasting Systems P A L SECAM BG , DK, I, L, Lp Channels and Digital : 474 MHz - 858 MHz Frequencies Analogue : 46.25 MHz - 862.25 MHz Cable TV (S 1- S20/ S21-S41) Input Signal Video: Analog 0,7 Vp-p 75 ohm positive Sync: TTL Level positive or negative, Seperate sync.
デバイスJVC Integrated Digital Wide LCD Panel TV LT-20DA6SSPの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
JVC Integrated Digital Wide LCD Panel TV LT-20DA6SSPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC Integrated Digital Wide LCD Panel TV LT-20DA6SSPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC Integrated Digital Wide LCD Panel TV LT-20DA6SSPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC Integrated Digital Wide LCD Panel TV LT-20DA6SSPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC Integrated Digital Wide LCD Panel TV LT-20DA6SSPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC Integrated Digital Wide LCD Panel TV LT-20DA6SSPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC Integrated Digital Wide LCD Panel TV LT-20DA6SSPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC Integrated Digital Wide LCD Panel TV LT-20DA6SSPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
