JVCメーカーTD-W254の使用説明書/サービス説明書
ページ先へ移動 of 12
TD-W254B/J INSTRUCTIONS DOUBLE CASSE T T E DECK DOUBLE CASSETTE DECK TD - W254 B/J For Customer Use: Enter below the Model No. and Serial No. which are located on the rear of the cabinet. Retain this information for future reference. Model No. Serial No.
W ARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS- TURE. IMPORT ANT (In the United Kingdom) Mains Supply (AC 230 V z , 50 Hz only) DO NOT cut of f the mains plug from this equipment.
INTRODUCTION Thank you for purchasing a JVC product. Read this instruction book carefully before operating to be sure of getting optimum performance and longer service life from the unit. CONTENTS Features .............................................
2. Installation 1) Avoid placing the unit on or adjacent to an amplifier , to pre- vent hum from being produced by some types of amplifiers. Move the unit to a place not affected by the amplifier .
CONNECTIONS • Do not switch the power on until all the connections are com- pleted. • Insert the plugs firmly , or poor contact will result, causing noise. • When the pin-plug cords are employed, always connect the white plug to the left channel terminal.
NAMES OF P ARTS AND THEIR FUNCTIONS 1 POWER switch ( ON OFF) (B version) POWER switch (On/Standby) (J version) 2 switch (ST ANDBY/ON) (B version) 3 Cassette holder (deck A) 4 Cassette operation buttons (deck A) : Press to wind the tape quickly from right to left.
t INPUT LEVEL control y Cassette operation buttons (deck B) : Press to wind the tape quickly from right to left. : Press to wind the tape quickly from left to right. (stop) : Press to stop the tape. Also press to stop both decks simulta- neously during dubbing.
RECORDING Deck B only Operate in the order of the numbers in the illustration. • Make sure the safety tab of the cassette has not been broken off. 1 T urn the power on. 2 Load a cassette for recording. 3 Set the DOLBY NR switch as required. 4 Set the REVERSE MODE switch as desired.
AUTOMATIC RECORD MUTING (DECK B) This facility is used to eliminate undesired sections and leave an appropriate non-recorded section. A. T o leave non-recorded sections of about 4–5 seconds automatically 1. When the undesired section comes during recording, press the REC/REC MUTE button and release it.
Automatic Source Selection (COMPU LINK-1, 3) When the provided remote cables are used for connecting this unit to other components which have COMPU LINK-1 or 3/SYNCHRO terminals, the switch-over of all system compo- nents is possible with simple one-touch of the source selector button of JVC’s amplifier or receiver .
T ape editing 1. Press the REC/REC MUTE button when finished dubbing a tune. Deck B automatically enters the record muting mode and leaves a non-recorded section of about 4-seconds then enters the record-paused mode. 2. Press the (stop) button of deck A and search for the next tune you want by using the , or PLA Y button.
SPECIFICA TIONS T ype : Double cassette deck T rack system : 4-track, 2-channel T ape speed : 4.8 cm/sec (1-7/8 inch/sec) (Normal) 9.5 cm/sec (3-3/4 inch/sec) (High) Frequency : (–20 dB recording) r.
デバイスJVC TD-W254の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
JVC TD-W254をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC TD-W254の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC TD-W254の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC TD-W254で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC TD-W254を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC TD-W254の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC TD-W254に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC TD-W254デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。