JVCメーカーUX-T550の使用説明書/サービス説明書
ページ先へ移動 of 20
Enter belo w the Model No . and Serial No . which are located either on the rea r, bot- tom or side of the cabine t. Retain this information for future ref erence.
G-1 IMPORTANT (In the United Kingdom) Mains Supply (AC 230 V Ó , 50 Hz only) DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
G-2 SAFETY INSTRUCTIONS “SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been disigned and manuf actured to meet international safety standards b ut, lik e any electrical equipment, care must be tak en if you are to obtain the best results and saf ety is to be assured.
1 Thank you for purchasing this JVC product. Please read these instructions carefully before starting operation to be sure to obtain optimum performance and a longer service life from the unit. CONTENTS Features .......................................
2 CONNECTIONS ● Do not switch the power on until all connections are completed. Antenna connection and adjustment ● AM (MW/L W) loop antenna adjustment ● Keep the loop antenna away from the unit and install it so that the best reception is obtained.
3 ● Attaching the speaker g rille Notes: ● The polarity of the two connected speakers will be the same if the blac k speaker cords are connected to the · terminals. If the speak- ers are connected with polarities rev ersed, stereo eff ect and tone will be degraded.
4 PO WER SUPPL Y A. Connection of AC po wer cord ● Connect the AC po wer cord after all other connections hav e been made. CA UTIONS: 1. ONL Y USE WITH JVC POWER CORD PRO VIDED WITH THIS UNIT TO A VOID MALFUNCTION OR D AMAGE T O THE UNIT .
5 NAMES OF P ARTS AND THEIR FUNCTIONS CD player/General section ~ button and po wer ST ANDBY indicator Ÿ AUX button ! Remote sensor section ⁄ Display window 1 Function/T rac k number display 2 Play.
6 REMO TE CONTROL UNIT Preparation before use ● Installing batteries in the remote control unit 1. Remove the battery cover from the back of the remote control unit. 2. Insert two “R6/AA (15F)” size batteries. ● Inser t the batteries with the ª and · ter minals matching the indication inside the battery compar tment.
7 One touch operation (COMPU PLA Y) Even when the po wer is set to ST ANDBY , pressing the b utton shown below s witches on the power and selects the source. V OLUME buttons + : Use to increase the volume. – : Use to decrease the volume. (Control range from VOLUME 0 to VOLUME 50.
8 Skip play ● During play , it is possible to skip f orward to the beginning of the ne xt track or back to the beginning of the track being played or the previ- ous track; when the beginning of the required track has been located, play starts automatically .
9 Programmed pla y (using the remote control unit) ● Up to 20 trac ks can be programmed to be play ed in any required order . The total playing time of programmed tracks is displayed (up to 99 minutes, 59 seconds). (Example: When programming the 2nd track to be played first, and the 6th track next, then the 12th track, etc.
10 COMPACT DIGITAL AUDIO BAND ONE TOUCH REC TAPE OPEN CD TUNER TIMER/SNOOZE STANDBY AUX MICRO COMPONENT SYSTEM UX-T550 VOLUME M U L T I J O G ACTIVE HYPER BASS PRO SLEEP 12 3 4 7 10 8 +10 AUX 9 6 5 AUTO PRESET DISPLAY PROGRAM RANDOM REPEAT BEAT CUT REVERSE MODE STEREO AUTO/MONO MULTI CONTROL BASS AHB.
11 Operate in the order sho wn RADIO RECEPTION ~ Press the TUNER/BAND button. ● The power is switched on and a band and radio frequency will be shown in the displa y .
12 ~ Load a cassette with side A f acing out. (Wind past the tape leader before starting recording.) Ÿ Load a CD and close the CD holder . ! Set to the CD mode. ⁄ Press the 7 button to set stop mode. @ Select the required reverse mode ( or ). ● When programmed play is required, program the required tracks using the remote control.
13 CLOCK ADJUSTMENT Names of parts in the clock/timer section, and their functions: ~ Timer mode indicator Ÿ Timer indicator (ON/OFF) ! CLOCK indicator ⁄ SLEEP indicator @ Time display ¤ CLOCK button # TIMER/SNOOZE button ‹ MUL TI JOG dial It is used to set the current time and perf or m timer setting.
14 TIMER OPERA TIONS Setting the timer ● The current time must be set before the timer can be used. ~ Press the TIMER/SNOOZE button f or 2 seconds or more. Ÿ Set the start time. (Example: T o set the timer to 12: 15.) ! Set the stop time. (Example: T o set the timer stop timer to 13: 15.
15 Timer recording of br oadcast ● The current time must be set bef ore the timer can be used. ● Make sure that the saf ety tabs of the cassette hav e not been broken off. Operations ~ Set the button to ON. Ÿ Load a cassette. ● Inser t the cassette with the side to be recorded f acing out.
16 SLEEP ● Sleep time settings of 30, 60, 90 or 120 minutes can be set. When you release the SLEEP button, the source is displayed after 5 sec. ● The sleep timer operation will start and the power will be switched off after the specified time. ● Checking the sleep time When the SLEEP button is pressed, the remaining sleep time is dis- played.
Enter belo w the Model No . and Serial No . which are located either on the rea r, bot- tom or side of the cabine t. Retain this information for future ref erence.
デバイスJVC UX-T550の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
JVC UX-T550をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC UX-T550の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC UX-T550の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC UX-T550で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC UX-T550を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC UX-T550の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC UX-T550に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC UX-T550デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
