KathreinメーカーUFS 923swの使用説明書/サービス説明書
ページ先へ移動 of 60
If you do not know the con fi guration of your satellite reception system, contact your specialist dealer for fi rst installation of the receiver. Operating manual part 1 UFS 923 Connection and start-up English Contents Safety instructions – important notes .
2 Power cable Make sure that the mains cable (power supply cable) is not damaged. Units with a damaged mains cable must be disconnected from the mains (unplug it at the socket) and repaired by an electrical specialist before setup. Only use the power pack supplied (if available).
3 Periods of extended absence, thunderstorms, mains socket accessibility In order to disconnect the unit from the mains completely , the mains plug must be unplugged from the wall socket! Therefore in.
4 Product return/original packaging Make sure that the fan at the rear of the unit and the ventilation slots on the unit are not blocked or covered in any way . Otherwise the unit may overheat. Adjust the fan speed to the temperature conditions in the receiver .
5 Scope of supply ■ UFS 923 ■ Remote control RC 676 or 675 ■ HDMI cable ■ Loop-through cable ■ Power cable ■ 2 batteries AAA 1.5 V ■ Operating manuals (part 1 and part 2) ■ Safety instructions (multi-lingual) The included accessories may differ from the illustrations.
6 Front/rear view of the receiver (front fl ap open) Connection and start-up 1 3 2 4 6 7 9 8 5 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMP O- NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.
7 Connection and start-up * ) CA modules and smart cards are not included with this product ** ) The unit is not fully disconnected from the mains (see the sections "Safety Instructions - Importa.
8 Connection and start-up Remove the cover on the rear of the remote control. Insert the two batteries supplied into the remote control. Ensure correct polarity of the batteries; the + and – markings as indicated inside the battery compartment. Slide the cover back onto the housing until it locks in place.
9 If you do not know the con fi guration of your satellite reception system, contact your specialist dealer. Connect the Sat IF inputs on the receiver to the satellite reception system. Use coaxial cable with an F standard connector (see illustration on right).
10 There are two ways you can access the digital audio. HDMI The stereo audio is transmitted to your TV set via the HDMI interface. If your TV set also supports Dolby Digital, you can also receive the Dolby Digital audio via the HDMI interface (providing it is broadcast by the channel provider).
11 If you wish to operate your UFS 923 on a single-cable system, please refer to the con- nection example for single-cable systems (see "T echnical Appendix", "Connection examples".
12 Before you start to use the UFS 923, read the sections "Safety Instructions - Important Instructions", "Important Information" and "Connection and start-up" through to the item "First installation". Do not connect the unit to the mains until all installation work has been properly carried out.
13 For this, refer to the operat- ing manual for your TV set and take care to select only those settings that your TV set can process. Press the (green) button to move to the next menu. The following on-screen display appears: Use the buttons here to select the basic set- tings for the video and audio output of the receiver to the TV set.
14 Important instruction for picture output using "YUV": The "YUV" output can be used only if "RGB" is not selected as the output signal for the TV Scart socket! In this .
15 Y ou should perform the tuner con fi guration/make changes yourself only if you are fully familiar with the particulars of your reception system. The settings for the tuner con- fi guration should be made by a specialist engineer for this reception system.
16 Y ou can set up the tuner con fi guration for the following types of reception systems: - DiSEqC™1.0 - DiSEqC™1.1 - Motorised antenna (DiSEqC™1.2/DiSEqC™1.3) - Simple LNB or - One Cable If your reception system is a single-cable system, continue from the item "Single-cable system" in this chapter .
17 Signal con fi guration for tuner 2 (only for "Separate" connection mode) Select the signal con fi guration for tuner 2 here. The currently selected setting is shown graphically in the connection example at the top left of the screen. Either: Same as tuner 1: Both tuners are connected to the same sig- nal source.
18 The following on-screen display appears: Select satellites - tuner 1 Here, you can select up to four available satellites to be included in the signal on tuner 1. Select the satellites you want and con fi rm the your selection with the button.
19 The following on-screen display appears: Satellite con fi guration - tuner 1 Here perform the settings for the fi rst satel- lite for tuner 1. LNB T ype: If your reception system does not have a Universal LNB, use the buttons to select the LNB types that are used in your reception system.
20 Connection and start-up DiSEqC™ repeat: The setting for how often the DiSEqC™ command must be repeated depends on the con fi guration of your reception system.
21 Press the (green) button. The following on-screen display appears: Select satellites - tuner 1 Here select up to a maximum of 64 sat- ellites whose signals should appear at tuner 1. T o do so, select the satellites you want and con fi rm the your selection with the button.
22 The following on-screen display appears: LNB T ype: If your reception system does not have a Universal LNB, use the buttons to select the LNB types that are used in your reception system.
23 Connection and start-up DiSEqC™ repeat: The setting for how often the DiSEqC™ command must be repeated depends on the con fi guration of your reception system. Refer to the documentation for your reception system or seek assistance from a specialist engineer .
24 Press the (green) button. The following on-screen display appears: Select satellites - tuner 1 Here select up to max. 64 satellites whose signals should appear at tuner 1. T o do so, select the satellites you want and con fi rm the your selection with the button.
25 The following on-screen display appears: Motor Control Here select the control type "DiSEqC™1.2". For this, refer to the documentation for your motorised antenna. Go to zero position Select the selection fi eld "Go to zero posi- tion".
26 If you subsequently wish to delete the set limits, switch to the selection fi eld "Reset limit positions" and press the button to con fi rm deletion of the limits. Y ou can then set new values for the limits. Once you have set all the limits, press the button.
27 Rotate antenna: Select the "Move motorised antenna" selection fi eld. Here you can control the movements of the motorised antenna, using the following buttons: Start slow rotation to.
28 Motor Control Here select the control type "DiSEqC™1.3". For this, refer to the documentation for your motorised antenna. My longitude Select the fi eld "My Longitude" and use the number pad here to enter your actual longitude.
29 Start slow rotation to the east Once you have reached the desired east / west limit, switch to the respective fi eld "Set current position for "****" limit" and press the button to con fi rm.
30 T est transponder: Select the "T est T ransponder" selection fi eld. Here you can select a transponder for checking the signal strength bar and signal quality bar to see whether your settings are correct. When you have completed all settings for this satellite, press the (green) button.
31 Press the (green) button. The following on-screen display appears: Select satellites - tuner 1 Select the satellite whose signal is present on tuner 1, and press the button to con fi rm your selection. The selected satel- lite will be identi fi ed with a check.
32 LNB T ype: If your reception system does not have a Universal LNB, use the buttons to select the LNB types that are used in your reception system.
33 Use the buttons to select "On" in the "Single-cable system used" line. Then use the buttons to switch to the "Single-cable system" selection fi eld. The following on-screen display appears: Select the single-cable system used in your reception system: - EXR .
34 The following on-screen display appears: Select satellites - tuner 1 Here select up to max. two satellites whose signals should appear at tuner 1. Select the satellites you want and con fi rm the your selection with the button. The selected satellites will be identi fi ed with a check.
35 Refer to the documentation supplied with your system for the settings for the SCRs, frequencies and any PIN assigned to the tuner . Y ou will fi nd there a printed list showing the assignment between the various SCRs and the respective transmission frequen- cies.
36 The following on-screen display appears: LNB type (settings): If your reception system does not have a Universal LNB, use the buttons to select the LNB types that are used in your reception system.
37 Press the (green) button. The following on-screen display appears: Select satellites - tuner 1 Here select the satellites whose signals appear at tuner 1. T o do so, select the sat- ellites you want and con fi rm the your selec- tion with the button.
38 T ransmission channel for tuner 1: Select a free available transmission channel (SCR 0 - SCR 3). T ransmission channel for tuner 2: Select a free available transmission channel (SCR 0 - SCR 3). When you have completed all settings for the satellite, press the (green) button.
39 The following on-screen display appears: Select satellites - tuner 1 Here select up to max. two satellites whose signals should appear at tuner 1. T o do so, select the satellites you want and con fi rm the your selection with the button. The selected satellites will be identi fi ed with a check.
40 Refer to the documentation supplied with your system for the settings for the SCRs, frequencies and any PIN assigned to the tuner . Y ou will fi nd there a printed list showing the assignment between the various SCRs and the respective transmission frequen- cies.
41 Perform the settings for the second tuner in the same way as for the fi rst tuner . When you have completed all settings, press the (green) button.
42 If you have selected more than one satellite for tuner 1, the receiver will automatically skip to the settings for the second satellite. Now perform the settings for the second satellite in the same way as described for the fi rst satellite.
43 If you do not wish to perform a channel search, press the (green) button and continue with the section "Date and T ime". If you want to perform a channel search, use the buttons to select "Y es".
44 Channel search mode Use the buttons to select the type of channels that are to be searched for . Y ou have three options: - "free-to-air and encrypted" All channels are searched fo.
45 Local UTC offset (time zone difference) Here you can select the local time offset to UTC (formerly GMT) (e.g. for Germany: + 1 hour). Y ou can set the offset in 30 minute steps.
46 Connection and start-up On completion of a successful fi rst installation (TV picture can be seen) we recommend having the receiver search for any available software update. It is a prerequisite that you have selected (included in the selection) the satellite ASTRA 19.
47 Connection and start-up Always follow the operating instructions from your Pay TV provider and the instruc- tions supplied with the smart card and the CA (conditional access) module! Smart cards an.
48 T roubleshooting In the event of a malfunction, fi rst check all the cable connections and operating states: 1. Receiver and TV set power plugs are connected to wall socket 2. Antenna cables on receiver input 3. Receiver and TV set correctly connected by a HDMI or Scart cable 4.
49 Service If, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer.
50 T echnical Appendix Advanced connection example 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO - NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.
51 T echnical Appendix T echnical Speci fi cations T ype UFS 923/250 GB UFS 923/1000 GB Article no./colour 20210190/silver - 20210191/black 20210182/silver - 20210183/black RF section Sat IF band MHz.
52 T echnical Appendix Sat IF connection examples 2 x UAS 571 Sat-ZF 950-2150 MHz **) ESD../ESC.. EXR 21 Signal 1 Signal 2 Position OPTION UC1 ** ) Overvoltage protection KAZ 1 1/KAZ 12 Individual rec.
53 T echnical Appendix ** ) Overvoltage protection KAZ 1 1/KAZ 12 Community antenna network systems (8 x Sat IF), multi-feed Community antenna network systems (16 x Sat IF), multi-feed.
54 T echnical Appendix ** ) Overvoltage protection KAZ 1 1/KAZ 12 Single cable systems.
55 T echnical Appendix ** ) Overvoltage protection KAZ 1 1/KAZ 12.
56 T echnical Appendix Connection examples for network functionality 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO - NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.
57 T echnical Appendix 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO - NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.400mA 22kHz LNB2 IN LNB1 IN Manifactured under license from Dolby Laboratories.
58 T echnical Appendix 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO- NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.400mA 22kHz LNB2 IN LNB1 IN Manifactured under license from Dolby Laboratories.
59 T echnical Appendix 100V-240V~ 50/60Hz max. 55W Elektroschock-Gefahr! Nicht öffnen! ON OFF VCR/AUX TV Video Y L Pb Pr R AUDIO KOMPO - NENTEN DIGITAL OUT DiSEqC 1.2 LNB 2 LOOP OUT LNB 1 LOOP OUT LOOP THROUGH IF INPUT 950-2150MHz 14/18V max.400mA 22kHz LNB2 IN LNB1 IN Manifactured under license from Dolby Laboratories.
Internet: www .kathrein.de KA THREIN-Werke KG • Anton-Kathrein-Strasse 1 - 3 • Postfach 10 04 44 • 83004 Rosenheim • Germany • T el +49 8031 184-0 • Fax +49 8031 184-385 936.
デバイスKathrein UFS 923swの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kathrein UFS 923swをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKathrein UFS 923swの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kathrein UFS 923swの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kathrein UFS 923swで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kathrein UFS 923swを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKathrein UFS 923swの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kathrein UFS 923swに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKathrein UFS 923swデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
