KawasakiメーカーC7478の使用説明書/サービス説明書
ページ先へ移動 of 24
Please read this manual and save it with your original sales receipt. T ools needed for assembly: Phillips Screwdriver , Hammer and Pliers (all not included); Cap Nut Assembly T ool (included). Use only with a Power Wheels ® 12 V olt Battery with Built-in Thermal Fuse and a Power Wheels ® 12 V olt Charger (both included).
Table of Contents Important Information A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B W arnings and Caution . . . . . . . . . . . . .
CAUTION • In the unassembled state, this package contains small parts. Adult assembly is required. • Use the charger in dry locations only . W ARNING • Prevent Injuries and Deaths • Direct Adult Supervision Required • Keep Children Within Safe Riding Areas.
Parts C Wheel - 4 • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded.
All Shown Actual Size Part Not Shown : Label Sheet .437 Cap Nut – 6 7 / 16 " W asher - 4 12 V olt Battery Cap Nut Assembly T ool Microphone 12-VOL T CHARGER 12 V olt Charger Pb #10 - 32 Lock Nu.
Parts Diagram D 1. V ehicle Body 2. Cowling 3. Seat 4. Wheel - 4 5. Hubcap - 4 6. Cap Nut - 6 7. Steering Column 8. Handlebar Neck 9. 12 V olt Battery 10. 12 V olt Charger 1 1. Microphone 12. Rear Wheel Driver - 2 13. Grip - 2 14. Handlebar - Front 15 Handlebar - Back 16.
Battery Charging E About Thermal Fuses Y our Power Wheels ® 12 volt battery is equipped with a built-in thermal fuse. The thermal fuse is a self-resetting safety device which automatically “trips” and shuts down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe.
Battery Charging • Plug the charger connector into the battery . • Plug the charger into a standard 120 volt wall outlet . Note: If power flow to the wall outlet is controlled by a switch, make sure the switch is “ON”. • Before first-time use, charge the battery for at least 18 hours.
2 Assembly • Fit a .437 cap nut onto one end of the rear axle. • T ap the other end of the rear axle with a hammer to secure the cap nut on the end of the rear axle. Hint: Y ou may want to position the cap nut on a scrap block of wood to protect the assembly surface.
W asher Rear Wheel Driver Cap Nut Cap Nut Assembly T ool Hubcap • Slide a washer onto the rear axle. • Slide the rear wheel driver onto the rear axle. Make sure the rear wheel driver fits onto the pins in the motor assembly . • Slide a wheel onto the rear axle.
Assembly TM • Press the tab under the back of the seat and lift to remove the seat. • Make sure the motor harness wires are positioned in the channel to prevent them from being pinched between the cowling and vehicle body . • Fit the rectangular opening in the cowling over the shifter handle.
Assembly 12 • Lift the front end of the vehicle. • Slide the straight end of the steering column through the hole in the upper steering linkage and out through the hole in the vehicle body . • Insert the curved end of the steering column into the hole in the lower steering linkage.
Assembly 13 • Fit the front handlebar assembly into the front of the handlebar . Screw Pegs Screw Pegs Holes Holes Handlebar Front Handlebar Housing • Fit the handlebar assembly onto the end of the steering column. Make sure the handlebar grip area points towards the rear of the vehicle.
R ® Assembly 14 • Bend the plastic tip at the end of the microphone cord so that it forms a "T". • Insert the "T" end of the microphone cord into the hole in the handlebar . Pull gently on the microphone cord to make sure it is secure in the handlebar .
Label Decoration G 15 Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelines in mind: • W ash your hands before applying the labels. • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils.
IMPORT ANT! Use only a Power Wheels ® 12 volt battery with built-in thermal fuse. Use of any other battery will damage your vehicle. Make sure that you charge the battery for at least 18 hours using the enclosed Power Wheels ® 12 volt charger before operating your vehicle for the first time.
If a battery leak develops, avoid contact with the leaking acid and place the damaged battery in a plastic bag. See information below for proper disposal. If acid comes in contact with skin or eyes, flush with cool water for at least 15 minutes and call a physician.
T each Safety Rules to Children While children can quickly develop the skill necessary to drive this vehicle, it is important to remember that their judgment skills are still very immature. Unsupervised driving by children can lead to serious injury .
• Make sure the shifter is in the LOW SPEED position. • Press the foot pedal. The vehicle will drive forward at a maximum of 2 1 / 2 mph. • Help your child practice steering to learn how far and how quickly to turn the handlebar when driving forward in low speed.
IMPORT ANT! T o avoid damaging the motors and gears, stop the vehicle before shifting between low and high speed. • Make sure the shifter is in the HIGH SPEED position.
Problems and Solutions Guide IMPORT ANT! If you experience a problem with your vehicle, first check the Problems and Solutions Guide below . If you still experience a problem, please contact Power Wheels ® Consumer Relations, toll-free at 1-800-348-0751 between 8 AM and 6 PM (EST) Monday through Friday .
Problems and Solutions Guide Short run time Undercharged battery Charge the battery . A new batter y should have been charged for at least 18 hours before using the vehicle for the first time. After first-time use, recharge the battery for at least 14 hours after each use.
Problems and Solutions Guide Problem Possible Cause Solution When the foot pedal is pressed Operation of vehicle in low speed It is possible that only one rear wheel may spin when both only one rear wheel spins rear wheels ar e raised off the gr ound and the vehicle is in low speed.
PRINTED IN MEXICO C7478pr-0920 IMPOR T ANT! DO NOT use this vehicle for the first time until you have charged the battery for 18 hours. Remember to … ✔ Charge the battery immediately after each use. ✔ Charge the battery once a month during storage, even if the vehicle has not been used.
デバイスKawasaki C7478の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Kawasaki C7478をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKawasaki C7478の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kawasaki C7478の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kawasaki C7478で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kawasaki C7478を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKawasaki C7478の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kawasaki C7478に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKawasaki C7478デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。