Kenmoreメーカー114.85925の使用説明書/サービス説明書
ページ先へ移動 of 17
Owner's Manual ® All Surface Floor Cleaner Model, Modelo 114.85925 CAUTION: Read and follow all safety and operating instructions before first use of this product, Sears, Roebuck and Co.
Before Using Your New All Surface Floor Cleaner .................. 2 Kenmore All Surface Floor Cleaner Warranty ...................... 2 Important Safety Instructions ....... 3-4 Parts and Features .................. 5 Assembly Instructions ..........
t _t I_s important to us, To VV/_I_I_I I I_1!_ reduce the risk of fire, electrical shock, injury to persons or damage when using your all surface floor cleaner, follow basic safety precautions including the following: Connect to a properly grounded outlet only.
Keep the All Surface Floor Cleaner on the floor. Do not use on stairs. Do not use an extension cord with this All Surface Floor Cleaner. Store the All Surface Floor Cleaner indoors. Put All Surface Floor Cleaner away after use to prevent tripping accidents.
It is important to know your All Surface Floor Cleaner's parts and features to assure its proper and safe use. Review these before using your All Surface Floor Cleaner.
Please pay special attention to these hazard alert boxes, and follow any instructions given. WARNING statements alert you to such dangers as fire, electric shock, burns and personal injury. CAUTION statements alert you to such dangerous personal injury and/or property damage.
OPERATING INSTRUCTIONS 1• Turn the quick reiease upper cord hook to either side and down to release the power cord. 2. Detach the power cord plug from the power cord and pull the cord off the quick release upper cord hook. 3. Plug the polarized power cord into a 120 Volt outlet located near the floor.
NOTE: Please read hard floor and carpet cleaning operating instructions prior to first use. For most effective cleaning, follow the recommended operating sequence below, IMPORTANT: For best cleaning results use a steady, forward and backward motion. Wet cleaning should be done at half the speed of dry vacuuming.
FILL Remove Tank-in- Tank" System from cleaner by pushing down on tank latch and tilting out. Remove measure cap from the rear of the Clean Water Tank. Pour 4 capfuls of Kenmore ® Hard Floor Concentrate Cleaner into Clean Water Tank. DO NOT USE PINE, SOLVENT I OR WAX BASED CLEANING SOLUTIONS IN CLEANER.
WASH AND DRY Step on Nozzle Setting pedal if necessary to switch from HARD FLOOR DRY VAC to WET SCRUB & VAC position. Slide Brush On/Off switch to the ON position. Pull Solution Trigger to start the flow of cleaning solution. NOTE; Cleaner will continuously dispense solution until Solution Trigger is released.
insert new nozzle by pushing securely into Nozzle Lock. NOTE: Make sure nozzle is inserted all the way in the Nozzle Lock, otherwise Nozzle Lock will not secure properly. Failure to install nozzle correctly can impact cleaning performance. NOZZLE LOCK TAB Turn Nozzle Lock Tab clockwise to lock nozzle onto cleaner.
Fill remainder of Clean Water Tank with warm water up to the MAX FILL line. Replace measure cap on Clean Water Tank. Replace Tank-in-Tank" System by inserting _ ottom first and tilting forward until tank latch fastens. WASH AND DRY With dry hands, plug cord Into properly grounded electrical outlet.
BRUSHROLL RESET BUTTON IMPORTANT: Your cleaner contains a reset button to protect the permanent belt should the brushroll clog. If this occurs, unplug the unit, remove debris from brushroll, and push reset button prior to resuming operation.
REPLACE TANK-IN-TANK" SYSTEM Return filter/float assembly to Dirty Water Tank. To ensure proper fit, make sure the arrow on the filter/float assembly lines up with the Align Filter Front arrow on Tank- in-Tank". Replace Tank-in-Tank TM System by inserting bottom first and tilting forward until tank latch fastens.
Replace filter by grasping angled top of filter and turning clockwise to lock onto fllter/fioat assembly. Return filter/float assembly to Dirty Water Tank. To ensure proper fit, make sure the arrow on the filter/ float assembly lines up with the Align Filter Front arrow on Tank- in-Tank TM.
Review this table to find do-it-yourself solutions for minor performance problems. Any service needed, other than maintenance described in this Owner's Manual, should be performed by a Sears or other qualified service agent. WARNING Disconnect electrical supply before performing maintenance to the unit.
Your Home Forrepair - in your home - of all majorbrand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself.
デバイスKenmore 114.85925の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kenmore 114.85925をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKenmore 114.85925の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kenmore 114.85925の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kenmore 114.85925で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kenmore 114.85925を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKenmore 114.85925の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kenmore 114.85925に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKenmore 114.85925デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
