Kenmoreメーカー385.15358の使用説明書/サービス説明書
ページ先へ移動 of 32
SERVICE MANUAL SEWING MACHINE MODEL 385, 15358 BER, 2006.
CONTENTS LOCATE AND iDENTiFY THE PARTS ................................................................. WiND THE BOBBIN .............................................................................................. PREPAREYOURTOPTHREAD ..............
SEWING MACHINE DIV. 20 MODEL 384. 15358 LOCATE AND IDENTIFY THE PARTS BOBBIN WINDING TENSION DISC THREAD GUIDE THREAD TAKE-UP LEVER BOBBIN WINDING SPINDLE BOBBIN WINDER STOPPER TOP THREAD TENSION CONT.
SEWING MACHINE DtV. 20 MODEL 384. 15358 WIND THE BOBBIN 1. PULL THE HANDWHEEL OUT. 2. DRAW THREAD FROM THE SPOOL. GUIDE THE THREAD AROUND THE THREAD GUIDE. THREAD THROUGH THE BOBBIN WINDER TENSION DISK "A" AND THE HOLE IN THE BOBBIN FROM THE INSIDE TO THE OUTSIDE.
SEWING MACHINE DtV. 20 MODEL 384. 15358 PREPARE YOUR TOP THREAD FOR THREADING THE MACHINE, FOLLOW THE NUMBERS IN ORDER AS SHOWN ON THE ILLUSTRATION. DOTTED LINES SHOW THE PLACES WHERE THE THREAD LOOPS AND THEN IS PULLED TIGHT. RAISE THE PRESSER FOOT LEVER.
SEWING MACHINE DtV. 20 MODEL 384. 15358 WHAT TO DO WHEN CONDITION CAUSE REFERENCE 1. SKIPPING STITCHES 2. FABRIC NOT MOVING 1. NEEDLE IS NOT INSERTED PROPERLY. 2. NEEDLE IS BENT OR WORN. 3. INCORRECTLY THREADED 4. NEEDLE OR THREAD ARE INAPPROPRIATE FOR FABRIC BEING SEWN.
SEWING MACHINE DtV. 20 MODEL 384. 15358 CONDITION CAUSE HOW TO FIX REFERENCE START WITH MEDIUM SPEED. 3. BREAKING UPPER THREAD 4. BREAKING BOBBIN THREAD 5. NEEDLE BREAKS 1. INITIAL SEWING SPEED IS TOO FAST. 2. THREAD PATH IS INCORRECT. 3. NEEDLE IS BENT OR DULL.
SEWING MACHINE DtV. 20 MODEL 384. 15358 CONDITION 6. NOISY OPERATION 7. DEFORMATION PATTERN CAUSE HOW TO FIX REFERENCE P.17 1. BACKLASH BETWEEN SHUTTLE HOOK GEAR AND LOWER SHAFT GEAR IS TOO GREAT. 2. LOWER SHAFT GEAR IS SEE MECHANICAL ADJUSTMENT "CLEARANCE BETWEEN NEEDLE AND HOOK (NO.
SEWING MACHINE DtV. 20 MODEL 384. 15358 SERVICE ACCESS FACE COVER f FACE COVER (A) (B) TO REMOVE: 1. REMOVE THE FACE COVER BY REMOVING THE CAP (A) AND SETSCREW (B). TO ATTACH: 2. FOLLOW THE ABOVE PROCEDURE IN REVERSE. BELT COVER TO REMOVE: 1. 2. LOOSEN SETSCREW (C).
SEWING MACHINE DtV. 20 MODEL 384. 15358 SERVICE ACCESS BASE PLATE f (A) BASE PLATE TO REMOVE: 1. LOOSEN THE SETSCREWS (A). 2. REMOVE THE BASE PLATE. TO ATTAC H: 3.
SEWING MACHINE DtV. 20 MODEL 384. 15358 SERVICE ACCESS FRONTCOVER f (H) (K) FRONT COVER (F) (D) (E) CAP TO REMOVE: 1. REMOVE THE FACE COVER, AND REMOVE THE BELT COVER (SEE PAGE 7). 2. REMOVE DIALS (A). 3. LOOSEN SETSCREWS (C), (D), (E), (F), AND (G), REMOVE SETSCREWS (H), (I) AND (J), AND THEN, REMOVE THE FRONT COVER.
SEWING MACHINE DtV. 20 MODEL 384. 15358 SERVICE ACCESS REAR COVER f (Y) TO 1. 2. REMOVE: REMOVE THE FACE COVER AND BELT COVER (SEE PAGE 7). NOTE: PULL UP THE SPOOL PINS. LOOSEN SETSCREWS (A), (B), (C) AND (D) (2 PCS.), REMOVE SETSCREWS (E), (F), (G) AND (H), AND THEN, REMOVE THE REAR COVER.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT NEEDLE THREAD TENSION TO CHECK: THE STANDARD UPPER THREAD TENSION SHOULD BE 65-95 g WHEN PULLING THE THREAD (COTTON THREAD #50) IN THE DIRECTION OF (B) WITH SETTING THE TENSION DIAL AT "3.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT BOBBIN TENSION TO CHECK: SET THE BOBBIN IN THE BOBBIN CASE AND PASS THE THREAD (COTTON #50) THROUGH THE TENSION SPRING. THE BOBBIN THREAD TENSION SHOULD BE 45-55g WHEN PULLING THE THREAD IN THE DIRECTION OF (B).
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT PRESSER BAR HEIGHT AND ALIGNMENT TO CHECK: 1. RAISE THE PRESSER FOOT LIFTER (A). 2. THE DISTANCE BETWEEN THE PRESSER FOOT (D) AND THE NEEDLE PLATE (E) SHOULD BE 6.0 MM (0.24"). ADJUSTMENT PROCEDURE: 1.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT NEEDLE SWING TO CHECK: ADJUST THE NEEDLE SWING ACCORDING TO THE FOLLOWING PROCEDURE, IF THE NEEDLE BAR STARTS MOVING SIDEWAYS WHILE THE NEEDLE IS IN THE FABRIC AT SEWING THE ZIGZAG PATTERN (WITH MAXIMUM ZIGZAG WIDTH).
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT NEEDLE DROP TO CHECK: WHEN THE NEEDLE SWINGS IN MAXIMUM ZIGZAG WIDTH, THE DISTANCE BETWEEN BOTH ENDS OF THE NEEDLE HOLE IN THE NEEDLE PLATE AND THE NEEDLE DROP POSITIONS SHOULD BE EQUAL. IF NOT, ADJUST AS FOLLOWS: ADJUSTMENTPROCEDURE: 1.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT CLEARANCE BETWEEN NEEDLE AND HOOK (ADJUSTMENT METHOD NO. 1) TO CHECK: THE CLEARANCE BETWEEN THE NEEDLE AND SHUTTLE RACE SHOULD BE -0.05 TO +0.10 MM. IF NOT, ADJUST AS FOLLOWS: ADJUSTMENT PROCEDURE: 1.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT CLEARANCE BETWEEN NEEDLE AND HOOK (ADJUSTMENT METHOD NO.2) TO CHECK: USE THIS ADJUSTMENT METHOD NO. 2 IF THE CLEARANCE CANNOT BE ADJUSTED BY METHOD NO.1. THE CLEARANCE BETWEEN THE NEEDLE AND SHUTTLE RACE SHOULD BE -0.
SEWING MACHINE DtV. 20 MODEL 384. 15358 FEED DOG HEIGHT MECHANICAL ADJUSTMENT MACHINE SETTING 1. STITCH SELECTOR: " 1CiD" 2. NEEDLE BAR: AT ITS HIGHEST POSITION. TO CHECK: 1. RAISE THE PRESSER FOOT. 2. PLACE THE FEED DOG HEIGHT GAUGE #68367 "A" ON THE NEEDLE PLATE.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT NEEDLE BAR HEIGHT MACHINE SETTING: 1. SET SELECTOR: " 1Ci_ i II TO CHECK: 1. OPEN THE SHUTTLE COVER. 2. REPLACE THE NEEDLE WITH THE TEST PIN #68368 "A". 3. REMOVE THE SHUTTLE HOOK AND INSERT THE RADIAL TIMING GAUGE #68366 "B" ONTO THE SHUTTLE DRIVER.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT NEEDLE TiMiNG TO SHUTTLE MACHINE SETTING 1. STITCH SELECTOR: " 1Ci_ i f_ TO CHECK: 1. OPEN THE SHUTTLE COVER. 2. REPLACE THE NEEDLE WITH THE TEST PIN #68368 (A). 3. REMOVE THE SHUTTLE HOOK AND INSERT THE RADIAL TIMING GAUGE #68366 (B) ONTO THE SHUTTLE DRIVER.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT BUTTONHOLE FEED BALANCE TO CHECK: WHEN SEWING BUTTONHOLE, THE STITCHES ON EACH SIDE OF BUTTONHOLE SHOULD BE THE SAME STITCH DENSITY. THE RANGE OF 9-12 STITCHES IN THE RIGHT SIDE ROW (BACKWARD FEEDING) AGAINST 10 STITCHES IN THE LEFT SIDE ROW (FORWARD FEEDING) IS CONSIDERED ACCEPTABLE.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT DISTORTED PATTERN TO CHECK: IF THE STRETCH STITCH PATTERNS ARE DISTORTED WITH SETTING THE STITCH LENGTH DIAL AT" V " (IN CASE OF.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT BARTACKFEED OFBUTTONHOLE TO CHECK: IF THE MATERIAL tS FED FORWARD OR BACKWARD WHEN SEWING BARTACK ON BUTTONHOLE, MAKE AN ADJUSTMENT AS FOLLOWS: ADJUSTMENT PROCEDURE: 1. SET THE PATTERN SELECTOR DIAL AT .
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT DISENGAGEMENT OF CAM FOLLOWER TO CHECK: IF THE CLEARANCE BETWEEN THE CAM FOLLOWER AND THE TOP CONVEX OF THE ZIGZAG CAM IS NOT ENOUGH, THE PATTERN SELECTOR DIAL IS BLOCKED OR WILL NOT SELECT THE CORRECT PATTERN.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT BUTTUNHOLEFUNCTION TO CHECK: BOTTONHOLES SHOULD BE ABOUT 3MM LONGER THAN THE LENGTH SET BY THE R FOOT. IF THIS LENGTH CANNOT BE OBTAINED, THEN CHECK AND ADJUST AS FOLLOWS: ADJUSTMENTPROCEDURE: 1.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT MOTOR BELT TENSION TO CHECK: 1. IMPROPER BELT TENSION MAY CAUSE NOISE, OVERLOAD OF MOTOR, SLOW RUNNING OR MOTOR BELT JUMPING. 2. THE BELT DEFLECTION SHOULD BE 7 MM - 9 MM WHEN PRESSING THE MIDDLE OF THE MOTOR BELT WITH APPROXIMATELY 300 GRAMS OF PRESSURE.
SEWING MACHINE DtV. 20 MODEL 384. 15358 MECHANICAL ADJUSTMENT TO REPLACE NEEDLE THREADER PLATE TO REMOVE 1. REMOVE THE FOOT HOLDER. 2. PULL OUT THE THREADER PLATE UNIT (A). TO ATTACH 3. PUSH THE THREADER PLATE UNIT (A) UP TO SNAP IT WITH THE PIN (B) AS SHOWN IN FIG.
SEWING MACHINE DtV. 20 MODEL 384. 15358 WiRiNG 1. WIRING FOR MACHINE SOCKET UNIT M: MOTOR L: LAMP RIDGED WtERS M L 2. WIRING DIAGRAM FOOT CONTROL MACHINE SOCKET i:i J / ,_ f ........................................... ::::_ LAMPSO_KET 1-- ............
SEWING MACHINE DtV. 20 MODEL 384. 15358 OILING FACTORY LUBRICATED PARTS WILL PROVIDE YEARS OF HOUSEHOLD SEWING WITHOUT ROUTINE OILING. HOWEVER, WHENEVER THE MACHINE tS BEING SERVICED, CHECK TO SEE IF ANY PARTS NEED TO BE LUBRICATED. OIL APPLY GOOD QUALITY SEWING MACHINE OIL TO THE POINTS (A, B, C, D, E) INDICATED BY BLACK ARROWS.
SEWING MACHINE DtV. 20 MODEL 384. 15358 SPECIAL TOOLS REQUIRED SL 0 TTED SCREWDRIVER FEED DOG HEIGHT GAUGE #68267 _EWDRIVER TE8 T PI/V #68868 A_LLEN WRENCH RADIAL TIMING GAUGE #68,366 30.
デバイスKenmore 385.15358の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kenmore 385.15358をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKenmore 385.15358の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kenmore 385.15358の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kenmore 385.15358で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kenmore 385.15358を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKenmore 385.15358の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kenmore 385.15358に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKenmore 385.15358デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
