KensingtonメーカーMP-20Eの使用説明書/サービス説明書
ページ先へ移動 of 47
A Proposal f or New Presentations MUL TI PR OJECT OR User’ s Manual MP-20E English Deutsc h Français Español.
E-2 Thank you f or purchasing the A VIO MP-20E LCD Projector . Please read this manual carefully in order to use the projector properly . After reading this, please keep it in a safe place together with the warranty sheet. Features of the MP-20E •V ery versatile three-in-one projector .
E-3 W ARNING ● If a fault occurs: • If you detect smoke , or a strange smell or sound, immediately disconnect the power cab le. It is dangerous to continue using the projector after a fault occurs. Return the projector to the dealer where it was purchased f or repair .
E-4 CAUTION • Installation •A v oid installing the projector in places where it ma y be exposed to: - Strong vibrations - Soot or steam - Direct sunlight or near a heater (35 ° C/95 ° F or highe.
E-5 • Lamp implosion •A DC type Super High pressure lamp is used in this projector and it is rare f or the lamp to explode during use. The unit is also designed to forcib ly tur n off the lamp because there is a high possibility that the lamp will break if it is used bey ond the lamp usage of 2000 hours (Refer to pages E-41 and E-42).
E-6 T able of Contents Safety Precautions ................................................. E-3 A Check of the Supplied Items and the Names of the P ar ts .............................. E-7 Supplied P ar ts Check ......................................
E-7 A Check of the Supplied Items and the Names of the Parts Supplied Parts Check Please check that the supplied parts are included. Lens cap MP-20E Projector Power cable (3 m) Remote control Coin-type lithium battery: CR2025 (Inside the remote control) User’ s Manual PC connection cable (2 m) Pull out the sheet before use.
E-8 A Check of the Supplied Items and the Names of the Parts Names and Functions of the Parts (Projector) Remote control IR sensor Lens cap Focus adjustment ring Tu rn this to adjust the f ocus. See P age E-22. Projection lens The image is projected from here.
E-9 A Check of the Supplied Items and the Names of the Parts Speaker (2 W , monaural) Theft prevention lock Please see the Note below . Remote control IR sensor Document reading area The document or printed material that you wish to project in the OHP mode is placed here.
E-10 A Check of the Supplied Items and the Names of the Parts Names and Functions of the Parts (Input Connectors) 1. Audio input connectors for the video Audio input connectors for use with the video. (Stereo sup- ported) See P age E-20. NO TE: The sound of the left and right channels is output from the monaural speak er.
E-11 A Check of the Supplied Items and the Names of the Parts Names and Functions of the Parts (Operation Panel) 1. POWER Button Switches the power of the projector on or off (standb y mode). • Only this button is eff ective when the projection lamp is off.
E-12 A Check of the Supplied Items and the Names of the Parts Names and Functions of the Parts (Remote Control) 1. POWER Button Switches the power of the projector on or off (standb y mode). • Only this button is eff ective when the projection lamp is off.
E-13 A Check of the Supplied Items and the Names of the Parts Operation of the Remote Control • Please use the remote control within a range of about 7 m from the remote control IR sensor of the projector (located at both the front and rear) and within an angle of 10 degrees to the left and 10 degrees to the right.
E-14 Pr ocedure Up to Pr ojection 1 Consideration of placement location and screen size Determine the screen and projector setup location. Set the projector on a strong and stable , lev el platform. 2 Connections with input equipment Connect your personal computer/video equipment.
E-15 Please use the f ollowing diagrams to determine the screen displa y size and the type of screen required for an y given projector location. Projection distances that will be in f ocus will be 1.3 m (4.3 feet) to 11.3 m (37.0 f eet) from the front of the lens.
E-16 Connection Precautions •T o protect this projector and the equipment to be connected, s witch off the power of each unit bef ore making connections. • Please read the various equipment instruction manuals f or information about the connection of the equipment and the method of use.
E-17 Pe r sonal Computer Input Connector The personal computer input connector uses a 15-pin mini D-SUB type connector . The pins and their corresponding signal inputs are described below . Pe r sonal Computer Input Connector 54321 10 9876 15 14 13 12 11 NO TE: The RGB (15-pin) input connector of the projector is of the analog type.
E-18 Connections with the P ersonal Computer Please check the matters described belo w when the image of the personal computer is not projected or when there is projection but the image is not correct.
E-19 Signal Name Resolution Horizontal Frequency Vertical Frequency Supported (Horizontal ⳯ Vertical) (kHz) (Hz) NTSC RGB – – 15.7 60 No PAL/SECAM RGB – – 15.6 50 No PC-98 Normal* 640 400 24.8 56 Yes PC-98 Hi 640 400 31.5 70 Yes VGA-GR1 640 480 31.
E-20 Connections with V ideo Equipment The video of a video tape deck or D VD player is pr ojected onto a large screen. NO TE: • When both Video and S-video connections hav e been made, S-video will be given priority for displa y . • When a video signal hav e a lot of noise, the image may be displa yed in monochrome .
E-21 Connection of the Power Cable and On/Of f Switching Switch On the P ower 1 Connect the power cab le The projector will enter the standby mode and the ON/ST ANDBY LED will light in red.
E-22 Adjustment of the Pr ojection Image Adjust the projection image to the screen. Adjusting the Pr ojection Image • When the image is shifted to the left or right, move the projector horiz ontally . (Align the center of the screen with the center of the projector lens.
E-23 Regular Operation This section describes the use of direct operation using the projector and remote control buttons . Please see the items on P age E-31 "Menu Operation Method" and P age E-34 "Menu Description" for inf ormation about operation using the menu.
E-24 Still Image Displa y Regular Operation This operation freez es the currently projected image. Operation with the Projector Press the FREEZE/CAPTURE button. Operation with the Remote Control Press the FREEZE/CAPTURE button. Cancelling the Still Image Displa y Operation with the Projector Press the FREEZE OFF button.
E-25 Changing the Orientation of the Pr ojection Image Effectiv e Only with OHP Input This operation s witches the (ver tical/horizontal) orientation of the currently projected image. The displa y of the switched screen is adjusted to match the width.
E-26 Capturing the Pr ojection Image A press of the FREEZE/CAPTURE button captures the currently projected OHP image and sa ves it as one or more images.
E-27 Enlarging and Reducing the Pr ojection Image This operation enlarges or reduces the siz e of projected image. During OHP input, adjustment from the same size to 6.25 times (length ratio 2.5 times) is permitted, while during PC or VIDEO input, adjustment from the same size to 16 times (length r atio 4 times) is per mitted.
E-28 Displa ying the P ointer Regular Operation This operation displa ys the pointer in the currently projected image. Deleting the Pr ojection Image and A udio This operation deletes the currently projected image and audio without s witching off the lamp .
E-29 Method of OHP Operation The maximum reading siz e of documents and pr inted material is 216 mm high by 288 mm wide. Consequently , when A4 paper (210 mm high and 297.5 mm wide) is placed on the projector , reading will be as illustrated in the diagr am below (which depicts the area that can be projected as the por tion with diagonal lines).
E-30 Menu Configuration Pntr setting Image adjustment Settings OHP/ PC / VIDEO Common During OHP Input OHP / PC / VIDEO Common During PC Input During VIDEO Input This item is added only when the menu is display ed during the full-screen dis- play of the OHP history .
E-31 Menu Operation Method Names and Functions of the Buttons Used in Men u Operation MENU Button Used to displa y a menu and to close a menu. POINTER/SET Button Used to finalize a setting after making the setting or adjustment. SCROLL 왖왔왗왘 Buttons Used in the selection of menu names and item names, and to set and ad- just item contents.
E-32 Method of Menu Operation Menu Operation Method This section describes the actual operation method. Adjustment of [K eystone] using the remote control is provided as an e xample.
E-33 4 Press the POINTER/SET Button Switches the menu to the sub menu (i.e ., the K eystone adjustment menu). Menu Operation Method 5 Make the adjustment with the SCR OLL 왗왘 b uttons while checking the pr ojection image SCROLL 왗 button: Each press causes the n umer ical v alue to decrease.
E-34 Menu Description Pntr setting This selects the shape, color , and siz e of the pointer . 䢇 P ointer shape ................. Selects the shape of the pointer from 2 types. 䢇 P ointer color ................... Selects the color of the pointer from amongst 3 types (i.
E-35 When PC input has been selected 䢇 Contrast ......................... Adjusts the contrast of the projected image in the range of -50 to 50. 䢇 Brightness ...................... Adjusts the br ightness of the pro- jected image in the range of -50 to 50.
E-36 When VIDEO input has been selected 䢇 Contrast ......................... Adjusts the contrast of the projected image in the range of -50 to 50. 䢇 Brightness ...................... Adjusts the br ightness of the pro- jected image in the range of -50 to 50.
E-37 Settings Menu Description This perf or ms settings related to the projector unit or while the projector is in use. 䢇 Lamp usage time ........... Displays the usage time of the lamp . "Replacement of the Lamp Unit" → See P age E-41 䢇 Input signal .
E-38 䢇 Projection mode ............. Selects the projection system of the projector from between F ront (front projection) and Rear (rear projec- tion). 䢇 Economy mode .............. ON (Economy mode): The brightness of the lamp will be approximately 80%.
E-39 Maintenance The projector is equipped with a built-in protection circuit to pre v ent fire and breakdown due to faults . When the LAMP/CO VER LED lights in red 䡬 Measures to be taken 1. Disconnect the power plug from the outlet. 2. Properly install the air filter .
E-40 When the power has failed (When all the LED go off with the po wer ON) 䢇 Measures to be taken 1. Disconnect the power plug from the outlet. 2. Check the f ollowing matters and perform the countermeasure properly .
E-41 Replacement of the Lamp Unit Guidelines for the replacement of the pr ojection lamp used in this projector are described belo w. (The time may be shorter depending on usage conditions.) When the usage time exceeds the time described belo w, the likelihood of rupture increases, the pr ojector will be for ced to turn off the projection lamp.
E-42 1 Remove the lamp unit co ver Using a minus scre wdr iver , loosen the scre ws of the lamp unit cov er , pull in the direction of the arrow , and remove the cov er . Maintenance 2 Loosen the mounting screws of the lamp unit Using a minus scre wdr iver , loosen the 2 scre ws of the lamp unit.
E-43 Maintenance 5 Reset the lamp usage time Please perform the operation indicated belo w in the standby mode (*). 6 Chec k that the indication of the lamp usage time has become "0 H" as illus- trated in the diagram to the right. If the usage time has not been reset, please reset it by follo wing Step 5 again.
E-44 Maintenance 1 Remove the air filter co ver Press the 2 tabs of the air filter cov er downward while s winging the cover outw ard to remove the air filter cov er .
E-45 Tr oubleshooting Power does not come on Projection lamp does not light There is no image Image is distorted Image is blurred The image flickers The image is out of adjustment The color is not rig.
E-46 Repair Service Procedure • Bef ore asking for repair ser vice, chec k the T roubleshooting section on page E-45 once more. If this check confirms a problem, contact the dealer where you bought the product.
E-47 Model Name MP-20E Type LCD Panel Size Drive System Number of Pixels Arrangement Projection Lens Optical Source Image Size Color Reproducibility Brightness Scan Frequency Maximum Resolution At RGB.
デバイスKensington MP-20Eの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kensington MP-20Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKensington MP-20Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kensington MP-20Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kensington MP-20Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kensington MP-20Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKensington MP-20Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kensington MP-20Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKensington MP-20Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
