King Kutterメーカー999995の使用説明書/サービス説明書
ページ先へ移動 of 36
2150 Eastern Av enue. Gallipolis, Ohio 456 31 ROT AR Y TILLER OPERA T OR MANUAL Part No 999995 www .kingkutter.com.
.
T O THE PURCHASER This manual contains v aluable information about y our ne w King Kutter II Rotary T iller . It has been carefully prepared to give y ou helpful suggestions for operating, adjusting, ser - v i cing and ordering repair parts. Keep this manual i n a convenient place for quick a nd easy re ference.
It is the purchaser and/or opera tor ’ s responsibility to…. Read and unders tand the information contained in this manual. O p e r a t e , l u b r i c a t e , a s s e m b l e a n d m a i .
5 CONTENTS ITEM P A GE Safety ......................................................................... 6 Assembly Instructions ................................................ 8 Before Putting Into Service ........................................ 8 Safety T raining .
S A F E T Y READ AND FOLLO W THE INSTRU C- TIONS IN THIS MANUAL AND ESP E- CIALL Y IN TH E SAFETY SECTION. F AILURE T O DO SO CAN RESUL T IN SERIOUS INJUR Y OR DEA TH. T AKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOU T THIS MANUAL IS USED T O CALL YOUR A TTENTION TO INST RUC- TIONS INVOL VING YOUR PERSON AL SAFETY AND T HE SAFETY OF OTH- ERS.
E Q U I P M E N T S A F E T Y G U I D E L I N E S Safety of the operator an d bystanders is o ne of th e main concerns in designing and devel- oping a tiller. However, every year a ccidents occur which could have been avoided by a few second s of thought and a more careful approach to handling equipment.
8 ROT AR Y TILLER ASSEMBL Y INSTRU CTIONS S T E P 1 With rotary t iller still in crate, lay flat on a level s urface . Cut banding straps on the tw o (2) up right crate pos ts. S T E P 2 Remove the top & upper side sections of the crate, leav ing the rotary t i l l e r resting on the bottom s ection.
9 STEP 6 Fill side ge arbox us ing gea r oil until the oil begins to ov erflow f rom the check plug hole . See Figure F on nex t page. STEP 7 Replace and tighten the 1/2‖ v ent plug and t he 1/8" check plug. Clean away an y excess oi l. See Figure G on nex t page.
10 Figure E Figure F Figure G Figure H Figure I Figure J.
S A F E T Y T R A I N I N G Safety is a primary concern in the design and manufa cturing of our product. Un- fortunately , our effo rts to provide s afe equipment can be wiped out by a s ingle careless act o f an operator or by stander .
P R E P A R T I O N N e v e r o p e r a t e t h e t r a c t o r a n d t i l l e r u n t i l y o u h a v e r e a d a n d c o m p l e t e l y u n d e r - s t a n d t h i s m a n u a l , t h e T r a .
13 O P E R A T I O N A L S A F E T Y The use of this equipment is subject t o certain hazards that cannot be protected against by t he mec hanical means or product design. All operators of this equip- ment must read and understand this entire manual, paying particular attention to safety and operating instructions , prior to using.
O P E R A T I O N A L S A F E T Y c o n t i n u e d . . . Never allow the tilling t ines to c ontact such items. Never assume an area is clear . Al w ays Check! Alway s stop the tractor , dise.
15 O P E R A T I O N A L S A F E T Y c o n t i n u e d . . . Pass rotary tiller diagonally through sharp dips and avoid sharp drops to prevent ―hanging up‖ tractor and rotary tiller . Practice will improve your s kills in maneu - vering on rough t errain.
16 A T TA C H I N G T O T R A C T O R S T E P 1 A t t a c h t o t r a c t o r ' s c a t e g o r y 1 t h r e e p o i n t h i t c h a s d e s c r i b e d i n t h e Tr a c t o r ' s O p e r a t o r ’ s M a n u a l .
17 A T TA C H I N G T O T R A C T O R c o n t i n u e d . . . . S T E P 5 Place and hold inner PTO s haft section next to outer section and check if PTO shaft is too long. Each section should end approximately 3 inches short of reaching u-joint shield on the opposite section.
18 S I Z I N G P T O S H A F T S T E P 1 Cutting the PT O shaft to length. NOTE: Be sure to c ut equal lengths of ea ch PT O shaft section. Clamp end of PT O shaft in a vice and cut off shield wher e marked. (Figu re 1-A & 1- B) S T E P 2 Using cut section of the shield as a guide cut shaft of f t he same amount.
19 O P E R A T I N G I N S T R U C T I O N S S T E P 1 Before each use perform the m aintenance described in maintenance section (page 20). S T E P 2 Read, understand, and f ollow the information on s.
Never travel at a fast ground speed w hile u sing the tiller , this cou ld damage it. Never attempt to turn the tractor o r travel in reverse w ith the PT O eng aged and the tiller in the ground. A lwa y s raise the tiller out o f the ground w hen ba cking up or attempting to turn.
Be sure electrical outlets and tools are properly grounded Use adequate ligh t for the job at hand . Make sure there is plenty ventilation. Never operate the engine of the towing vehicle in a close d building. The exhaust fumes may cause asphyx iation.
22 S A F E T Y S I G N L O C A T I O N S The types of safety signs and lo cations on the equipmen t are shown in the ill ustration below . Good sa fety requires that y ou familiarize yoursel f with the various safety signs, the type of w arning and the area, or particular function rela ted to that area, tha t re- quires your SA FTY A W A RENESS.
23 1.
24 2 3.
25 4 5.
26 6 7 MODEL NO. DESCRIPTION SN# XXXXXXXXXX.
27 NOTES:.
TILLER: EXPLODED VIEW 28.
Ref. No. Part Name TG - 48 TG - 72 TG - 60 1 Lift Arm Brace 380108 380108 380108 2 Lift Arm (Left hand) 3 10085 310085 310085 3 Lift Arm (Right hand) 310086 310086 310086 4 Tail Rod Assembly 505116 505116 505116 5 Center Piece Kit 505025 505025 505025 6 Lift Arm Spacer Kit 505030 505030 505030 7 Tine Pkg.
30 Ref. No. Part Name 147122 Part No. 1 Safety Shield 124311 2 Roll Pin 170120 3 Male Tube End Yoke 151045 4 Female Tube End Yoke 151050 5 Tractor End Yoke 151035 6 Inner Tube 14 Series 151090 7 Outer Tube 14 Series 151091 8 Cross Kit # 4 170015 9 Quick Disconnect Pin 170110 10 Clutch Spring w/ Compression Bolts & nuts (Pkg.
31 TG SERIES OUT -BOARD HUB 184070 Ref. No. Part Name 184070 1 Hub Housing 902341 2 Cap 902342 3 Self Aligning Ball Bearing (1310) 902019 4 Seal Double Lip (Pkg.
32 TG SERIES GEARBOX 184069.
33 Ref. No. Part Name Part Number 1 Retainin g Ring 90mm 902005 2 Retainin g Ring 40mm 902006 3 Pressure Plate Plug 1/2‖ - 14 NPT 902007 4 Sq. Hd. Plug 1/4‖ - 18 NPT 902008 5 Flat Washer (Main) 902009 6 Lock washer M- 12 902010 7 Bolt M- 12 - 25 902011 8 Bolt M-8-16 (Pkg.
34 TG SERIES T OP GEA RBOX A SSEMBL Y.
35 TG SERIES T OP GEA RBOX P A RTS LIST Ref. No. Part Name Part Number 1 Retainin g Ring 72mm 902301 2 Retainin g Ring 40mm 902302 3 Housing RTA - 50 902329 4 Pressure Plate Plug 1/2‖ - 14 NPT 902304 5 Sq. Hd. Plug 1/4‖ - 18 NPT 902305 6 Bolt M- 10 -25 (Pkg.
36 1. Limited War ranty. King Kutter, Inc. (―King Kutter‖), P.O. Box 1200, W in f ield, Alabama 35594, warrants to the original retail pur- chaser (―Purchaser‖) that the product t hat is the subject of this sale is f ree from defects in material and work- manship at the time of sale.
デバイスKing Kutter 999995の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
King Kutter 999995をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKing Kutter 999995の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。King Kutter 999995の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。King Kutter 999995で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
King Kutter 999995を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKing Kutter 999995の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、King Kutter 999995に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKing Kutter 999995デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
