Konica MinoltaメーカーTC-Xの使用説明書/サービス説明書
ページ先へ移動 of 22
Konica TC-X posted 5-11-'03 This camera manual library is for reference and historical purposes, all rights reserved. This page is copyright by mike@butkus.
(4) A new design extremely bright viewfinder makes accurate focusing easier, increases visibility of in-finder data. (5) Accepts the full range of Hexanon interchangeable lenses and a wide range of Konica accessories, including a electronic flash unit.
Film advance: Single action top lever, wind angle of 135°, 20° play. Film rewind: Crank driven rewind mechanism, film rewind button resets automatically Frame counter: Additive type, auto-reset 4.butkus.org Size, weight: Body 130 x 84 x 44mm ( 5. I I x 3.
1. Changing the lens.
1. Changing the lens Attaching the lens: Align the red dot on the lens barrel with the red dot (22) on the camera body and gently insert the lens barrel into the camera.
2 . Inserting Battery The Konica TC-X uses a single LR03, R03 dry battery (AAA size) as the power source for the AE system 4.butkus.org 1) Open the battery chamber cover (36) by pushing the cover in (he direction of the arrow.
3. Power switch The power switch functions as the power ON-OFF/shutter release button safety lock system. 1) When the power switch (2) is turned "ON" the light meter is activated and the shutter release is unlocked. 2) When the switch is turned "OFF the meter is turned off and the shutter release locks.
1) When the film speed dial (14) is set at "DX" " the camera automatically reads the film speed of the film magazine, so manual film speed setting is unnecessary. This is only effective with "DX" type films. 2) When non-Ding type film is used, turn the film speed dial (14) to set the camera for the rating of the film.
5. Loading film.
5. Loading film 1) Turn the power switch (2) "on." Pull the rewind knob (16) all the way out and the back cover (37) of the camera will open. 2) Place a roll film into the film cassette chamber (31), then push the rewind knob all the way back down.
(6) Turn the film advance lever (1) as far as it turns and press the shutter release button (7). Repeat until the number " I " appears in the frame counter (26). *When the film is advancing properly, the film rewind knob will turn counterclockwise.
6. Automatic exposure system (AE) 1) Set the aperture ring (7) at the "AK" mark (18), and the aperture ring is then locked. 2) Turn the shutter speed dial (3) and set it at the desired speed. With ISO 100 film, for example, a typical shutter speed for shooting outdoors in clear weather is 1/125 or 1/250 see, 1/30 or 1/60 for indoors.
Microdiaprism Split image Matted plane Focus at the center of the viewfinder When focusing, point the camera directly at the main subject (area of the picture that is most important), to use the split image and microdiaprism for precise focusing.
clear when using the camera with close-up attachment and telephoto lens, for example. Checking the exposure Checking the aperture: The correct aperture setting for the shutter speed to which the camera is set will be shown by the needle in the finder.
7. Unloading film 7. Unloading film After shooting a whole roll of film, the film must be rewound before being removed from the camera. 1) With "DX" type film, the roll is finished when the number in the frame counter (26) is the same as the number in the film check window (41).
3) Flip up the film rewind crank (15) and turn it in the direction of the arrow. 4) When film is completely rewound, rewind crank will turn freely. Then open the back cover and remove the film magazine for processing.
1) Press the AE release button (24) and turn the aperture ring (7) to set the aperture manually. *A red warning mark will appear m the finder to show that the camera is set for manual aperture control.
9. Using the self-timer 9. Using the self-timer Turn the self-timer lever (10) counterclockwise (in the direction of the arrow) as far as it goes. Then press the shutter release button.
1) Attach the Konika X-20N AUTO to the hot shoe (13) on the camera. 2) Switch from AE to manual aperture mode and set the aperture at f/4 (ISO 100) or at f/8 (ISO 400), according to the film speed.
Bright subject, dark background If the subject in the frame is brightly lit (ea. by direct sunlight) and the background is dark, the subject will be overexposed in normal AE photography. To prevent this, move up close to the subject and press the shutter half way down to lock the AE mechanism.
Using depth of field Depth of field is the range in front of and behind the point on which the lens is actually focused which also appears In sharp focus in the photograph. It has the following features: 1) The smaller the lens aperture ("F" stop) the greater the depth of field.
A. Depth-of-field for f/16 B. Depth of field for F4 C. Depth-of-field scale D. Distance/Aperture scale index mark E. Infrared mark F. Distance scale.
デバイスKonica Minolta TC-Xの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Konica Minolta TC-Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKonica Minolta TC-Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Konica Minolta TC-Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Konica Minolta TC-Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Konica Minolta TC-Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKonica Minolta TC-Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Konica Minolta TC-Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKonica Minolta TC-Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
