KregメーカーPRS1020の使用説明書/サービス説明書
ページ先へ移動 of 18
RT1 01 16 V ersion 20070701 · Woodworking machines are dangerous, and can cause personal injury if not used properly . · Read safety instructions and operating instructions for your machine completely , before using products. Using this system before understanding its safe and proper use could result in serious injury to the operator .
Precision R outer T able T op Assembly T urn the Router T able top (#2) so it’ s face down on the fl oor . Locate the two Support Struts (#7) and align them to the pre-drilled holes in the bottom of the Router T able T op. Mount the struts to the top using the eight ¾” Coarse Thread Screws (#16).
Precision R outer T able T op Assembly Precision R outer T able T op Assembly Step 5: Mounting the router to the Insert Plate Step 6: Leveling the Insert Plate to the Opening Step 7: Installing & .
1 Phenolic Insert Plate RT10101 1 2 T able T op RT10102 1 3 T-Miter Track RT10103 1 4 2” Reducing Ring RT10107 1 5 1-13/64” Reducing Ring RT10106 1 6 Brass Starting Pin RT10108 1 7 Support Strut R.
Precision R outer T able T op Assembly Precision R outer T able T op Assembly Step 5: Mounting the router to the Insert Plate Step 6: Leveling the Insert Plate to the Opening Step 7: Installing & .
Precision R outer T able T op Assembly T urn the Router T able top (#2) so it’s face down on the fl oor . Locate the two Support Struts (#7) and align them to the pre-drilled holes in the bottom of the Router T able T op. Mount the struts to the top using the eight ¾” Coarse Thread Screws (#16).
RT1 01 16 V ersion 20070701 · Woodworking machines are dangerous, and can cause personal injury if not used properly . · Read safety instructions and operating instructions for your machine completely , before using products. Using this system before understanding its safe and proper use could result in serious injury to the operator .
Tools Required: • 7/16” Open Ended Wrench • Flat Head Screwdriver • Phillips Head Screwdriver Router T able Fence Precision ASSEMBL Y INSTRUCTIONS Item# PRS1 0 1 0 7. RT10142 V ersion 20070701 www.kregtool.com • 800.447.8638 When jointing, it’s always best to make light passes so you’ll probably use the 1/32-in.
Safety Guidelines Step 13 Step 14 Step 15 Locate the 48” Center Reading T ape (#35) and trim each side to the 17-15/16” mark with a sturdy scissors. Carefully remove one corner of the backing, apply the tape 1/16 from the edge of the Large Fence and continue to remove the backing while you press the tape across the surface of the fence.
Precision R outer T able Fence Assembly Precision R outer T able Fence Assembly 2. 5. Locate the Mounting Rail (#1) and slide it over the ¾” Hex Bolts (#5) as shown. If you intend on using the Kreg Micro-Adjuster (sold separately), position the mounting rail so it’s fl ush with the front edge of the T able Mount.
Hardware # Description Part# Quantity 1 MOUNTING RAIL RT10124 1 2 CLAMP BLOCK ASSEMBL Y RT10125 1 3 FENCE MOUNT RT10126 1 4 LARGE FENCE RT10122 1 5 T ABLE MOUNT RT10123 1 6 FENCE FACE RT10128 2 7 FENC.
Precision R outer T able Fence Assembly Precision R outer T able Fence Assembly 2. 5. Locate the Mounting Rail (#1) and slide it over the ¾” Hex Bolts (#5) as shown. If you intend on using the Kreg Micro-Adjuster (sold separately), position the mounting rail so it’s fl ush with the front edge of the T able Mount.
Safety Guidelines Step 13 Step 14 Step 15 Locate the 48” Center Reading T ape (#35) and trim each side to the 17-15/16” mark with a sturdy scissors. Carefully remove one corner of the backing, apply the tape 1/16 from the edge of the Large Fence and continue to remove the backing while you press the tape across the surface of the fence.
Tools Required: • 7/16” Open Ended Wrench • Flat Head Screwdriver • Phillips Head Screwdriver Router T able Fence Precision ASSEMBL Y INSTRUCTIONS Item# PRS1 0 1 0 7. RT10142 V ersion 20070701 www.kregtool.com • 800.447.8638 When jointing, it’s always best to make light passes so you’ll probably use the 1/32-in.
2 Universal Steel Stand Tools Required: • Square • 1/2” Socket wrench & extension • (2) 3/4” Open-end or adjustable wrenches • Phillips head driver bit Please call us at 800-447-8638 with any questions regarding the assembly of this stand.
Installing Height adjusters: In this step you will be adding the Height Adjusters to the bottom of each Leg. Place the Steel Stand face-down on your work surface so that all four legs are pointed up in the air , and are easily accessible, as shown in image A .
Installing Height adjusters: In this step you will be adding the Height Adjusters to the bottom of each Leg. Place the Steel Stand face-down on your work surface so that all four legs are pointed up in the air , and are easily accessible, as shown in image A .
2 Universal Steel Stand Tools Required: • Square • 1/2” Socket wrench & extension • (2) 3/4” Open-end or adjustable wrenches • Phillips head driver bit Please call us at 800-447-8638 with any questions regarding the assembly of this stand.
デバイスKreg PRS1020の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Kreg PRS1020をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKreg PRS1020の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kreg PRS1020の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kreg PRS1020で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kreg PRS1020を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKreg PRS1020の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kreg PRS1020に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKreg PRS1020デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。