Krell IndustriesメーカーKPS 25sの使用説明書/サービス説明書
ページ先へ移動 of 19
The Leader in Engineering KPS 25s Krell Playback System TM Instructions for Use Owner’s Reference.
KPS 25s Krell Playback System TM CONTENTS Krell®lndustries, Inc. 45 Connair Road Orange, CT 06477-3650 USA TEL 203-799-9954 FAX 203-799-9796 E-MAIL krell@krellonline.
CE Marking Unpacking This product complies with the EMC direc- 1. Open the shipping box and remove the tire (89/336/EEC) and the low-voltage top layer of foam. You will see these items: directive (73/23/EEC). Introduction Thank you for your purchase of the Krell KPS 25s Krell Playback System TM.
Placement WARNINGS The Krell Playback System TM must not be located where it could be exposed to drip- ping or splashing fluids. Before you install the KPS 25s into your system, review the following guidelines to choose the location for the KPS 25s. This will facilitate a clean, trouble-free installation.
NOTE: Attach the Acrylic Cover before con- necting the flex-foil cable. Carefully remove the Acrylic Cover from the velvet pouch and place it on a soft surface.
INSTALLING THE ACRYLIC COVER ONTO THE KPS 25s, continued = Acrylic Cover, Right View, Perpendicular to the KPS 25s ACRYLIC COVER 3. With the Acrylic Cover perpen- dicular to the KPS 25s, line up the pins in the Acrylic Cover (B) with the notches in the top of the KPS 25s (C).
INSTALLING THE A(;RYLIC COVER ONTO THE KPS 25s continued PUBH-PULL P’N ~ ( ) The "lop o] the KPS 25s with Acrylic Cover and Flex-Foil Cable in Piece A PUSH-PULL PIN B PIN IN ACRYLIC COVER C NOTCH IN TOP COVER D FLEX-FOIL CABLE E FLEX-FOIL RECEPTACLE 5.
Connecting the KPS 25s to Your System WARNING When making connections to this compo- nent or any other, make sure the power amplifier is Off. Make sure all cable termi- nations are of the highest quality, free from frayed ends, shorts, or cold solder joints.
The KPS 25s is equipped with the following analog and digital inputs: 1 set of balanced analog inputs (via an XLR connector) 3 sets of single-ended analog inputs (via RCA connectors) 1 set of tape mon.
SECTION 1 SECTION 2 SECTION 3 SECTION 4 KPS 25s DIRECT AGCESS CONTROLLER SECTION 7 SECTION 6 SECTION 5 2 SPDIF co-axial digital outputs (via The XLR pin RCA connectors) below: 1 AES/EBU digital output (via an XLR Pin 1 connector) Pin 2 KrelP recommends the use of balanced Pin 3 interconnects.
Using the fixed outputs in this configuration may cause damage to associated power amplifier and loudspeakers. Additional Connections RC-5 The RC-5 input makes custom installation easy and secure by accepting baseband RC-5 input commands from hardwired remote controllers.
II Section 2 Special Play Functions Repeat Press once to repeat the entire disc or track program continuously. Press twice to repeat the current track continuously. Press a third time to cancel this function. When selecting the desired Repeat function, press the Repeat button once and REPEAT will appear in the Compact Disc Transport Display Window.
Play To activate playback from the beginning of the CD, press the Play button after inserting the CD onto the transport. Clamp the CD down, and close the Acrylic Cover. Playback will begin from the first track. If the CD is loaded and the disc contents have been scanned, press Play on the front panel or remote control.
Section7 Drive Off Turns the CD transport On/off. Amplifier and Display I/Vindow Functions Power The main power switch that turns the KPS NOTE: Use the Amplifier Power and Amplifier Display buttons to access a Krell ® 25s On/off. amplifier connected to your system.
Menu Functions 4. Turn the Level Control Knob to select the input to which you want to assign a custom name. All initial set u p and subsequent system con- figuration adjustments may be made using either the Tabletop Remote Controller, or the front panel controls.
To change the shutter operation mode: 1. Press the Menu button. The word MENU will appear. 2. Turn the Level Control Knob until the word SHUTTER appears. 4. Turn the Level Control Knob to select . the input for volume trim. 5. Press the Menu button again.
Warranty THERE ARE NO USER-SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT. The KPS 25s KrelP Playback System has a limited and transferable warranty of five years for parts and labor and three years on transport related parts.
Return Authorization dealer, distributor, or the KrelP Service Procedu re Department for assistance. Krell ® is not responsible for any damage IMPORTAN~ Ifyou believe there is a prob- incurred in transit.
KrelP Industries, Inc. 45 Connair Road Orange, CT 06477-3650 USA TEL 203-799-9954, FAX 203-799-9796 E-MAIL krell@krellonline.com www.krellonline.com KPS 25s Krell Playback System TM Specifications FREQUENCY RESPONSE 0.
デバイスKrell Industries KPS 25sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Krell Industries KPS 25sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKrell Industries KPS 25sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Krell Industries KPS 25sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Krell Industries KPS 25sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Krell Industries KPS 25sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKrell Industries KPS 25sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Krell Industries KPS 25sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKrell Industries KPS 25sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
