Krell IndustriesメーカーMS 6760の使用説明書/サービス説明書
ページ先へ移動 of 54
Mainboard MS 6760 V ers.1.
ii FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
iii Lithium Battery Statement CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufactuer.
iv 1. Always read the safety instructions carefully. 2. Keep this User’s Manual for future reference. 3. Keep this equipment away from humidity. 4. Lay this equipment on a reliable flat surface before setting it up. 5. The openings on the enclosure are for air convection hence protects the equipment from overheating.
v Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL . We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes with- out notice.
vi CONTENTS System Specification ............................................................................ viii Chapter 1. Introducing Mainboard ...........................................................1-1 Mainboard Layout........................
vii Modem Module Connector: CN21...........................1-16 Jumper.............................................................................1-17 Clear CMOS Jumper: J2.............................................1-17 Slots.......................
viii System Specifica tion M/B - MS-6760 (Proprietary F/F), 185 x 290 mm (4 layer) CPU: - Support Socket 478 for Pentium ® 4, 2.8 GHz Chipset: - SiS 651 + SiS 962 Memory: - DDR 333 x 2, support memory up to 2.0GB On-Board Audio: - AC’97 Codec integrated in ALC 650, support 5.
ix On-Board Headers & Connectors - Rear Panel: Parallel Port x 1, Serial Port x 1, VGA x 1, PS/2 x 2, Mic in/Line in/ Line out x 1, USB x 2, LAN (RJ45) x 1, SPDIF/O x 1, Modem (RJ11) x 1 - Front P.
1-1 Introducing Mainboard Introducing Mainboard Introducing Mainboard Introducing Mainboard Introducing Mainboard Introducing Mainboard 1.1 Mainboard Layout 1.1 Mainboard Layout 1.1 Mainboard Layout 1.1 Mainboard Layout 1.1 Mainboard Layout 1.2 CPU/Memory 1.
1-2 Chapter 1 1 . 1 Mainboard l a yout See the following for the mainboard layout: BA TT + SiS651 SiS 962 CN28 SM Bl ue bi rdV L+ CN26 CN4 CN5 CN1 J2 C8 CN 8 ATX Power Sup p ly BIOS PC I S lo t 1 To p.
1-3 Introducing Mainboard 1 .2 CPU/memory The mainboard supports I ntel ® Pentium ® 4 processors in the 478-pin package. The mainboard uses a CPU socket called PGA478 for easy CPU installation. When you are installing the CPU, make sure the CPU has a heat sink and a cooling fan attached on the top to prevent overheating.
1-4 Chapter 1 1 .3 Power Suppl y The system is equipped with a 200W(PFC) ATX power supply. The power cord of power supply has been connected to the connectors on the mainboard when shipped out. You can find two connectors (20-Piin & CN 20) on the mainboard.
1-5 Introducing Mainboard 1 .4 Front p anel The Front Panel is independent and extended from the mainboard. It’s connected to the Front Panel Connector on the mainboard.
1-6 Chapter 1 IEEE 1394 Port: J1394-1 The bigger 6-pin IEEE 1394 Port on the back panel is designed for you to connect to IEEE 1394 devices without external power.
1-7 Introducing Mainboard Mic-in/Head-Phone Mic-in is a connector for microphone. Head-Phone is a connector for Speakers or Headphones. OPTICAL SPDIF-in The OPTICAL connector allows you to receive the audio file of SPDIF interface for recording and playing.
1-8 Chapter 1 1 .5 B a c k p anel The Back Panel provides the following ports: VGA Port Keyboard USB x 2 Optical SPDIF-out Speak-out Lin-in Mic-in Parallel Port LAN Port Mouse Serial Port 9-Pin Male DIN Connector 1 2 3 4 5 6 7 8 9 Serial Port The mainboard offers a 9-pin male DIN serial port .
1-9 Introducing Mainboard The mainboard provides one DB 15-pin female connector to connect a VGA monitor. VGA Port Pin Definition Analog Video Display Connector (DB-15s) PIN SIGNAL DESCRIPTION 1 Red 2.
1-10 Chapter 1 The mainboard provides one standard RJ-45 jack for connection to Local Area Network (LAN). You can connect a network cable to the LAN jack.
1-11 Introducing Mainboard Parallel Port The mainboard provides a 25-pin female centronic connector as LPT. A parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) mode.
1-12 Chapter 1 Audio Port Speak-out is a connector for Speakers or Headphones. Line In is used for external CD player, Tape player, or other audio devices.
1-13 Introducing Mainboard 1 .6 Connectors CN22 (Primary IDE Connector) - CN22 can only connect a HDD. CN23 (Secondary IDE Connector) - CN23 can only connect a CD-ROM drive.
1-14 Chapter 1 CD-in Connector: CN16 The connector is for CD-ROM audio connector. TV -T uner Card Connector: CN13 The mainboard provides the connector to connect the TV-Tuner card. The TV-Tuner card is included in the package. You can insert the TV-Tuner card into the PCI Slot 1.
1-15 Introducing Mainboard Front Panel Power Connector: CN4 The mainboard provides a Front Panel connector for electrical connec- tion to the Front Panel switches and LEDs.
1-16 Chapter 1 LCM Connector: CN8 The connector is used to connect the LCM on the front panel. CN 8 Modem Module Connector: CN21 The mainboard provides the connector to connect the modem module. The modem module is directly inserted into the connector without an extra cable.
1-17 Introducing Mainboard 1 .7 Jumper There is a CMOS RAM on board that has a power supply from external battery to keep the data of system configuration. With the CMOS RAM, the system can automatically boot OS every time it is turned on. That battery has long life time for at least 5 years.
1-18 Chapter 1 1 .8 Slo ts PCI Slot 1 AGP (Accelerated Graphics Port) Slot The AGP slot allows you to insert the AGP graphics card. AGP is an interface specification designed for the throughput demands of 3D graphics.
2-1 Setting BIOS Function Setting BIOS Function Setting BIOS Function Setting BIOS Function Setting BIOS Function Setting BIOS Function 2.1 Entering Setup 2.1 Entering Setup 2.1 Entering Setup 2.1 Entering Setup 2.1 Entering Setup 2.2 The Main Menu 2.
2-2 Chapter 2 2. 1 Entering Setup Power on the computer and the system will start POST (Power On Self Test) process. When the message below appears on the screen, press <DEL> key to enter Setup.
2-3 Setting BIOS Function Getting Help After entering the Setup menu, the first menu you will see is the Main Menu. Main Menu The main menu lists the setup functions you can make changes to. You can use the control keys ( ↑↓ ) to select the item. The on-line description of the highlighted setup function is displayed at the bottom of the screen.
2-4 Chapter 2 2.2 The main menu Once you enter Phoenix-Award ® BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. The Main Menu allows you to select from twelve setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
2-5 Setting BIOS Function Power Management Setup Use this menu to specify your settings for power management. PNP/PCI Configurations This entry appears if your system supports PnP/PCI. PC Health Status This entry shows your PC health status. Frequency/Voltage Control Use this menu to specify your settings for frequency/voltage control.
2-6 Chapter 2 2.3 st andard cmos fea tures The items in Standard CMOS Features Menu are divided into 12 categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item.
2-7 Setting BIOS Function If you select Manual , related information is asked to be entered to the following items. Enter the information directly from the keyboard. This information should be provided in the documentation from your hard disk vendor or the system manufacturer.
2-8 Chapter 2 2.4 adv anced bios fea tures Quick Boot Setting the item to Enabled allows the system to boot within 5 seconds since it will skip some check items. Available options: Enabled , Disabled . Boot Sequence The items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system.
2-9 Setting BIOS Function CPU L2 Cache ECC Checking This setting allows you to enable or disable the ECC (Error-Correcting Code) feature for error detection and correction when data passes through L2 cache memory. Setting options: Disabled , Enabled .
2-10 Chapter 2 Security Option This specifies the type of BIOS password protection that is implemented. Set- tings are described below: Option Description Setup The password prompt appears only when end users try to run Setup. System A password prompt appears every time when the com- puter is powered on or when end users try to run Setup.
2-11 Setting BIOS Function 2.5 adv anced c hipset fea tures Advanced DRAM Control 1 Press <Enter> to enter the sub-menu and the following screen appears: System Performance The DRAM timing is controlled by the DRAM Timing Registers. The Timings programmed into this register are dependent on the system design.
2-12 Chapter 2 MA 1T/2T Select This setting controls the SDRAM command rate. Setting to Auto allows the SDRAM command rate to be determined by the BIOS. Selecting MA 1T/MA 2T makes SDRAM signal controller run at 1T/2T rate. 1T is faster than 2T. Setting options: Auto, MA 2T, MA 1T.
2-13 Setting BIOS Function 2.6 integra ted peripheral s SIS OnChip IDE Device Press <Enter> to enter the sub-menu and the following screen appears: Internal PCI/IDE This setting enables or disables the internal primary and secondary PCI & IDE controllers.
2-14 Chapter 2 IDE Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance.
2-15 Setting BIOS Function USB 2.0 Supports Set to Enabled if you need to use any USB 2.0 device in the operating system that does not support or have any USB 2.0 driver installed, such as DOS and SCO Unix. Setting options: Disabled , Enabled . USB Keyboard Support Select Enabled if you need to use a keyboard in the operating system.
2-16 Chapter 2 Onboard Super IO Device Press <Enter> to enter the sub-menu and the following screen appears: Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDD) installed on the system board and you wish to use it.
2-17 Setting BIOS Function EPP Mode Select The onboard parallel port is EPP Spec. compliant, so after the user chooses the onboard parallel port with the EPP function, the following message will be dis- played on the screen: “EPP Mode Select.” At this time either EPP 1.
2-18 Chapter 2 Onboard LAN Device This item is used to enable or disable the onboard LAN controllers. Setting options: Enabled, Disabled. Onboard Lan Boot ROM The items enable or disable the initialization of the onboard LAN Boot ROMs during bootup. Selecting Disabled will speed up the boot process.
2-19 Setting BIOS Function 2.7 Power management setup Sleep State This item specifies the power saving modes for ACPI function. If your operating system supports ACPI, such as Windows 98SE, Windows ME and Windows 2000, you can choose to enter the Standby mode in S1(POS) or S3(STR) fashion through the setting of this field.
2-20 Chapter 2 Power Management This item is used to select the degree (or type) of power saving and is related to these modes: Suspend Mode and HDD Power Down . There are three options for power management: Min Saving Minimum Power Management. Suspend Mode=1 Hour Max Saving Maximum Power Management.
2-21 Setting BIOS Function After AC Power Lost This setting specifies whether your system will reboot after a power failure or interrupt occurs. Available settings are: Off Leaves the computer in the power off state. On Leaves the computer in the power on state.
2-22 Chapter 2 USB Wake Up from S3 This item allows the activity of the USB device to wake up the system from S3 (Suspend to RAM) sleep state. Settings are: Enabled and Disabled . PS2KB Wake Up from S3/S4/S5 This setting allows you to enter “Any Key” (max.
2-23 Setting BIOS Function 2.8 pnp/pci configura tions This section describes configuring the PCI bus system and PnP (Plug & Play) feature. PCI, or P eripheral C omponent I nterconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its special components.
2-24 Chapter 2 IRQ Resources The items are adjustable only when Resources Controlled By is set to Manual . Press <Enter> and you will enter the sub-menu of the items. IRQ Resources list IRQ 3/4/5/7/9/10/11/12/14/15 for users to set each IRQ a type depending on the type of device using the IRQ.
2-25 Setting BIOS Function Shutdown Temperature When the processor reaches the preset temperature, the ACPI-aware system will be shut down. Settings: Disabled, 85 o C/185 o F, 90 o C/194 o F .
2-26 Chapter 2 2. 1 0 Frequen cy/Vol t age Control CPU Clock Ratio This setting controls the multiplier that is used to determine the internal clock speed of the processor relative to the external or motherboard clock speed.
2-27 Setting BIOS Function CPU Frequency Use this item to select the appropriate frequency for your CPU FSB. Options: Default, 100MHz, 133MHz. DRAM Frequency This setting shows the current frequency of DDR DRAM (read only). Options: By SPD, 200MHz, 266MHz, 333MHz.
デバイスKrell Industries MS 6760の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Krell Industries MS 6760をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKrell Industries MS 6760の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Krell Industries MS 6760の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Krell Industries MS 6760で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Krell Industries MS 6760を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKrell Industries MS 6760の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Krell Industries MS 6760に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKrell Industries MS 6760デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
