Krell IndustriesメーカーNoneの使用説明書/サービス説明書
ページ先へ移動 of 61
Home Theater Standard Instructions for Use Owner’s Reference.
Home Theater Standard Surround Sound Preamplifier/Processor Instructions for Use v. 99.3 Krell Industries, Inc. 45 Connair Road Orange, CT 06477-3650 USA TEL 203-799-9954 FAX 203-891-2028 E-MAIL krell @ krellonline.com WEBSITE http.’/Jwww.krellonlin e.
Contents INTRODUCTION DEFINITION OF TERMS UNPACKING PLACEMENT _. AC Power Guidelines GETTING STARTED Read Tills First ... An Introduction to System Setup FRONT PANEL DESCRIPTION BACK PANEL DESCRIPTION.
Illustrations FIGURE 1 The Home Theater Standard Front Panel F~GURE 2 The Home Theater Standard Back Panel FIGURE 3 The Home Theater Standard Remote Control Page 6 12 16 iv Krell Home Theater Standard.
Introduction Thank you for your purchase of the Krell Home Theater Standard Surround Sound Preamplifier/Processor. The Home Theater Standard provides optimum music and cinema soundtrack reproduction quality through Krell C.urrent Mode, discrete Class A direct-coupled circuitry, and balanced outputs on all six channels.
Unpacking Open the box and remove the top layer of foam. You see these items: 1 Home Theater Standard 1 IEC connector (AC power) cord 1 Home Theater Standard handheld remote control - 2 AAA-size 1.5 Volt batteries 1 T-15 Torx wrench ~small "U’ type) 1.
Placement Before you install the Home Theater Standard into your system, review the following guidelines to choose the location for the component. This will facilitate a clean, trouble- free installation. The Home Theater Standard does qot require any type-of special rack or cabinet for installation.
Getting Started READ THIS FIRST Perform the following steps to make the On-Screen Display (OSD) viewable on your video monitor. The video format and video signals of the Ho_me Theater Standard and the video monitor need to match before the OSD is viewable.
4. Verify that the video monitor’s video signal input corresponds to the Home Theater Standard’s video signal output. Press the menu key on the handheld remote control to verify that the OSD is now viewable on the video monitor.
5 6 7 8 9 10 11 12 13 14 16 15 17 22 3 2 1 4 18 19 20 21 Basic Operation 1 Power Button 2 Power LED 3 Stand-by LED 4 Infrared Sensor input Device Selection Buttons and LEOs 5 DVD Button and LED 6 LD B.
Front Panel Description See Figure I on page 6 The Home Theater Standard front panel provides power on and off; input, zone, and processing mode selection; monitoring and display of processor status; and balance and volume control.. The front panel components are described below.
Front Panel Description, continued 6 LD Button and LEDs Use this button to select the laser disc device. 7 SAT Button and LEDs Use this button to select the satellite feed device. _. 8 VCR1 Button and LEDs Use this button to sele.c.t the VCR device. 9 TV Button and LEDs Use this button to select the television device.
Front Panel Description, continued 17 Infrared Emitter Emits the Home Theater Standard remote operation code to a learning remote. See Program Remote, on page 45. A learning remote control can be programmed to o.per.ate the Home Theater Standard via the infrared emitter.
Front Panel Description, continued 22 Front Panel Display The front panel display provides status messages for Home Theater Standard operations, including volume and balance level, decoding mode, and zone information. In addition, when a new device is selected, the physica~ inputs are displayed.
Front Panel Description, continued 29 Level Down and Up Buttons Use the volume level buttons to adjust the output for the entire system as well as balance and individual levels for the center speaker, rear speakers, and subwoofers. The volume level is shown in the front panel display.
31 33 31 34 41 44 45 5O 32 32 37 38 39 3635 40 434246 48 49 47 52 E6 54 : 55 53 Analog Outputs and Inputs 31 Balanced Analog Audio Outputs 32 Single-ended Analog Audio Outputs 33 Multi-Channel Audio Output Connector 34 B-1 Left and B-1 Right 35 Tape In Left and Right 36 Tape Out Left and Right 37 VCR1 I.
Back Panel Description See Figure 2 on page 12 The back panel of the Home Theater Standard provides all input and output connections, remote control inputs and outputs, power on and off, and power connection. The back panel functions are described below.
Back Panel Description, continued 38 VCR1 Out Left and Right The Home Theater Standard is equipped with one set of single-ended outputs with RCA connectors, for a VCR audio source. 39 Zone 2 Out Left and Right -- The Home Theater Standard is equipped with one set of single-ended zone 2 audio outputs with RCA connectors.
Back Panel Description, continued 48 Component Video Outputs The Home Theater Standard is equipped with one set of component video outputs with RCA connectors. Component video uses three wires (labeled Y, Cr, and Cb on back panel) to convey the video signal, including the OSD.
56 57 6O 61 65 68 ’59 ’58 63 62 67 66 69 71 75 78 73 72 .77 76 79 81 80 83 82 Power Functions 56 Amp Key 57 FITS Key Zone Selection 58 Main Key 59 Z2 Key Device Selection Keys 60 DVD Key 61 LD Key.
Remote Control Description See Figure 3 on page 16 The Home Theater Standard remote control provides on and off, input selection, processing mode selection, speaker volume and balance adjust, and mute functions, as well as access to the System Setup a.
Remote Control Description, continued Zone Selection 58 Main Key Use this key to select the main zone for a device. 59 Z2 Key Use this key to select zone. 2 for a device. See Main Zone and Zone 2 Operation, on Note .’. The Home Theater Standard defaults to the main zone.
Remote Control Description, continued 69 Tape Key Use this key to compare the output from an analog tape recorder to the original source while making a recording. Note Once a device is selected, press the device selection key again to change the tape output source bus to the zone currently selected.
Remote Control Description, continued Control Function Keys 74 Bal Key Press this key to convert the volume level controls to balan_c, e controls. See Balance Button (24), on page 10. Use the Center, Rear, and Sub keys to change taste trims (make temporary speaker output adjustments of -~1.
Connecting the Home Theater Standard to Your System This section provides information about connecting your Home Theater Standard to analog and digital sources, video sources, and amp.
Connecting the Home Theater Standard to Your System, continued The Home Theater Standard is also equipped with four S-video inputs and four composite video inputs. S-video cables transmit the color and luminance components of the video signal separately.
System Setup and Configuration Overview This page outlines the System Setup and Configuration Menus. These easy-to-follow, step-by-step menus let you set up your Home Theater Standard for optimum performance. Detailed instructions begin on page 24. Krell recommends that you configure your component in the following order: 1".
System Setup and Configuration The remote control is the main input device for the Home Theater Standard. All initial setup and subsequent system configuration adjustments must.
4. Use either the front panel power button (1) or the remote control HTS key (57) power on the Home Theater Standard. The blue power LED (2) on the frent panel illuminates. The Home Theater Standard is now in operational mode and ready to be configured.
Bass Range The speaker setup screen also shows the bass ranges for the front, center, and rear speakers. Options available are not bass limited (FUL..L-RANGE) or bass limited (LIMITED). The option you select depends on the low frequency capabilities of each speaker in your system.
After selecting the appropriate option for your speakers, press enter (83), highlight oK, and press enter (83).again. You return to the speaker system setup menu.
Note Any speaker not configured in the speaker system setup menu displays N/A (not available) for the distance specification. 3. CALIBRATE VOLUME The third menu option, calibrate volume/allows you to calib~.te each channel using the Home Theater Standard’s internal noise generator.
The following screen appears: KRELL HTS -CALIBRATE VOLUME- LEFT CENTER RIGHT 0 dB ~ 0 dB 0 dB LREAR SUB R .REAR 0 dB 0 da 0 dB Auto Noise Sequence Set the SPL meter to C weighting and slow response. After initializing, the LEFT channel dB setting bl!nks, and you hear bar~ded white noise through the left speaker.
Program Material The program material option uses the same screen as manual noise sequence, but with external material. The source plays, simultaneously, from all configured speakers. This allows you to individually adjust speaker balances based on your listening preferences rather than SPL readings.
After selecting the device (the example used is DVB) that you want to configure, press enter (83). The CONFIGURE DVD screen appears: KNELL HTS -CONFIGURE- DVD ~ CONFIGUR~ VIDEO ~ CONFIGURE AUDIO .... CONFIGURE MODE .... CONFIGURE TRIG OK Configure Video Input Press enter 83) to select this option.
Assign Video Format KNELL HTS -ASSIGN VIDEO FORMAT- OVO NTSC OK PRESS ENTER AND USE 1",], TO SWITCH BETWEEN NTSC AND PAL After selecting the appropriate video format, select oK and press enter (83) to return the ASSIGN VIDEO INPUT screei3. Select OK and press enter (83) to return to the CONFIGURE DEVICES screen.
Assign Analog Input .If you select ANALOG, the ASSIGN ANALOG INPUT screen appears: KRELL HTS -ASSIGN ANALOG INPUT- DVD 1~ S-1 <~ ’ , OK PRESS ENTER AND USE 1" $ TO SWITCH BETWEEN ANALOG INPUTS When this screen appears, you see the blinking cursor at s-1.
When you enter this screen, you see the blinking cursor at COAX1. To select another digital input option (COAX1, COAX2, COAX3, COAX4, COAXS, COAX6, OPT1, OPT1, UNASSIGNED), follow directions at bottom of screen. Select the UNASSIGNED digital input option if the selected device does not use a digital output, for example, an analog VCR.
The CONFIGURE 12 V TRtGGER screen appears: KRELL HTS -CONFIGURE 12 V TRIGGER- DVD )l, MODE ,N DELAY TRIGGER1-. 0 1 SEC. TRIGGER2 0 1 SEC. TRIGGER3 0 1 SEC. TRIGGER4 0 1 SEC. OK Select Trigger Mode Use the 1" ,I, keys (80) to move the blinking cursor to the MODE for the desired trigger, and press enter (83).
Use the 1" ,], keys (80) to select the desired trigger mode and press enter (83) to select. You return to the CONFIGURE 12 VTRIGGER screen, which now reflects the change you just entered. Adjust Trigger Delay On the CONFIGURE 12 V TRIGGER scree.n, use the ~ key to move the blinking cursor to DELAY and press enter (83).
The Home Theater Standard uses two types of trims: master volume trims and taste trims. Master volume trims (mode, device, and analog input) change the volumes of all speakers at once, are programmed, and do not change unless reprogrammed through the menu.
When you enter this screen, you see the blinking cursor at STEREO. To select another option (DOLBY DIGITAL, DTS, DOLBY PRO LOGIC, STEREO, MUSIC1, MUSIC2) press enter (83), then use $ ,1, keys (80) to scroll through the options. Select the desired mode, and press enter (83).
When you enter this screen, you see the blinking cursor at DVD. To select another option (LD, SAT, VCR, TV, CD, TUNER, AUXl, AUX2, TAPE), press enter (83), then use 1" $ keys (80) to scroll through the options.
Input Gain You can boost weaker signals by increasing the input gain value at the bottom left of this screen (in 3 dE}, 6 dE}, and 9 dB gain increments). To maximize your system’s signal to noise ratio for a particular input, the input gain value applied to the signal should be increased (if ne.
6. OPERATION The final option, OPERATION, allows you to choose background color for your video display, configure on-screen display and front panel display brightness, choose serial control format, select music modes, program a learning remote control to operate the Home Theater Standard, and program.
Background Color To .change the background color for your video menu display, select. B/kCKGROUND COLOR and press enter (83). The MENU BACKGROUND COLOR screen ap pears: KRELL HTS -BACKGROUN£~ COLOR- -" MENU BACKGROUND COLOR BLACK BLUE GREEN RED OK The blinking cursor appears at MENU BACKGROUND COLOR.
To change the line number on which the display appears, use the 1" $ keys (80) to move to LINE NUMBER. With the blinking cursor next to LINE NUMBER, press enter (83), then use ~ .], keys (80) to select the screen line. The range is 0 (top line of screen) through (bottom line of screen).
Configure Music The next item in the OPERATION menu, CONFIGURE MUSIC, allows you to determine which music modes you want. Select CONFIGURE MUSIC and press enter (83).
Virtual Acoustic Environments ON STAGE L/R/C/S/RR FRONT ROW L/R/S/RR GENERAL ADMISSION L/.R/S/RR ORCHESTRA MEZZANINE BALCONY MONO L/R/C/S/RR UR/C/S/RR LIWCISIBR ENHANCED STEREO PARTY C/S L~R/CIS L/R/C.
KRELL HTS -PROGRAM REMOTE MODE- ONLY I"ANO ,I, SAVE AND RECALL ARE ALLOWED - ON FRONT PANEL, REMOTE I,.N_P. UT IS INACTIVE. PRESS ENTER TO CONTINUE -’ - OK Note The infrared sensor on the front panel is rendered inactive until programming is complete.
Configure More Use this menu to select dynamic range compression modes with the user button or to change the DTS autoswitch setting. KRELL HTS - CONFIGURE MORE- USER BU’I-rON SETUP DTS AUTOSWITCH Us.
DTS Autoswitch DTS AUTOSWITCH ON keeps your Home Theater Standard operating in DTS mode, even if the bit stream is interrupted. Bit stream interruption--which can occur in some devices when you press .
Saving Setup, Recalling Setup, and Restoring Factory Default System Configuration Settings SAVING SETUP SETTINGS To save the settings that you have entered, press arid l~ld the save button (28) for approximately four seconds. The front panel displays SAVING SETUP while the settings are being stored in the Home Theater Standard’s no.
Operating the Home Theater Standard After the Home Theater Standard is connected to source devices and amplifiers, and system setup configured, the Home Theater.Standard is ready for operation. ON/OFF/STAND-BY -. 1. Insert the AC power cord into the IEC power connector (55) on the Home Theater Standard.
Operating the Home Theater Standard, continued MAIN ZONE AND ZONE 2 OPERATION The Home Theater Standard has two audio zones, main and zone 2. The main zone consists of the main viewing or listening area, and zone 2 consists of another listening area.
Play Either Zone Main Zone 1. With the Home Theater Standard in operational or stand-by mode, press the HTS key (57) to activate the main zone. 2. Select the device you wish to play. - 3. Press HTS key again to turn off the main zone. Zone 2 1. With the Home Theater Standard in stand-by mode, press the Z2 key (59).
1. Press the TV button (9) or key (63) to select the device. Begin playing the device. 2. Press the prev key (78). 3..Press the CD button (10) or key (64). Begin playing the device. If you wish to keep playing the TV but listen to the radio in_s.tead: 1.
Warranty This Krell product has a limited warranty of five years for parts .and labor on circuitry. Should this product fail to per- form at any time during the warranty, Krell will repair it at no cost to the owner, except as set forth in this warranty.
Return Authorization Procedure If you believe there is a problem with your component, please contact your dealer, dis- tributor, or the Krell factory to discuss the problem before you return the component for repair.
Specifications SIGNAL TO -NOISE RATIO "A" WEIGHTED TOTAL HARMONIC DISTORTION (THD) UNWEIGHTED INPUTS ANALOG AUDIO DIGITAL AUDIO VIDEO ANALOG TAPE OUTPUTS ANALOG CHANNEL ANALOG TAPE DIGITAL.
DECODING MODES SURROUND ENHANCEMENT MODES DIMENSIONS WEIGHT SHIPPING UNIT ONLY Dolby Pro Logic Dolby Digital DTS Digital Surround Sound 9 Kreil Music Surround Modes 19.
デバイスKrell Industries Noneの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Krell Industries Noneをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKrell Industries Noneの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Krell Industries Noneの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Krell Industries Noneで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Krell Industries Noneを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKrell Industries Noneの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Krell Industries Noneに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKrell Industries Noneデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
