KTI Networksメーカー2028の使用説明書/サービス説明書
ページ先へ移動 of 21
Installation Guide KTI 10/100 Fast Ethernet Switch KS2028 P/N:750-0087-001 DOC.971005-KS2028-K.
Ó 1997 KTI Networks Inc. All rights reserved. No part of this docu- mentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc.
10/100 Fast Ethernet Switch Installation Guide DOC.971006-KS2028-NK P/N: 750-0087-002.
The information contained in this document is subject to change without prior notice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents 1. Introduction ............................................................................... 1 1.1 Features .................................................................................................................. 2 1.2 Specifications .
1. Introduction Driven by recent advances in desktop computing technology, today’s network applications have grown speed, power and the ability to pro- cess information. To meet the demands of these more powerful applica- tions, the switch has been developed to alleviate congestion and im- prove performance on your Ethernet network.
1.1 Features Designed for resolving congestion problems caused by bandwidth-hun- gry devices and bandwidth-intensive applications as well as a high num- ber of users, the switch not only adheres to the IEEE 802.3 10BASE-T and 100BASE-T standard, but also features: • Various TP ports for flexible connection to servers and hubs.
1.2 Specifications Network ports 10BASE-T ports 8 10/100BASE-TX port 1 Expansion port slot 1 Filtering rate 10BASE-T ports 14,880 pps 10/100BASE-TX port 148,800 pps Expansion port slot 148,800 pps For.
2. Installing the Switch The switch is designed to operate in workgroup environments without a complicated configuration procedure. It also features an auto-select 100- 240V, 50/60Hz power supply unit, which works in most countries around the world.
Rack Mounting For mounting the switch into a 19-inch rack, a pair of mount brackets is included in the pack. Figure 2-2 Install Rack Mount Brackets Install the switch into a 19-inch rack as illustrate.
2.3 Front Panel and Rear Panel Figure 2-4 Components on the Front and Rear Panel • Eight 10BASE-T switched ports (Port #1 to Port #8) Each port consists of an RJ-45 connector and is used for connec- tion to a 10BASE-T hub or node.
• Diagnostic LED indicators The indicators provide the operating status of the hub and the network ports. The status includes power, partition, duplex, activity, and collision. • Configuration switches Two configuration switch groups are located on the rear of the switch unit.
Figure 2-6 100BASE-FX Port Module Before installing any optional modules, first turn the power to the switch off. To install a module into the expansion port slot, follow these steps: 1. Turn off the power switch. 2. Remove the cover of the slot. Figure 2-7 Remove the Slot Cover 3.
2.5 Setting the Configuration Switches Open the configuration switch cover on the rear of the unit. There are two switch groups as illustrated below: Figure 2-9 Configuration Switches The following table specifies the definition of each switch: The M switch only functions for Port #9 and Port #10.
When a operation mode is accepted by the remote device, the mode is used for the data transfer between the port and the connected device. Full-duplex opera- tion enables two devices to transfer data bi-directionally at the same time.
3. Making Network Connections 3.1 Network Switched Ports There are ten ports on the switch for connection to ten LAN segments. Each segment is an independent shared network in one collision-do- main.
3.2 10BASE-T Switched Ports The individual RJ-45 connectors of Port #1 to Port #7 are defined as X type connectors and have fixed pin assignments as follows: The following table lists the devices to which Port #1 to #7 can connect : Device connected Cable used Computer 10BASE-T port Cat.
The following table lists the devices to which Port #8 can connect : Device connected Crossover SW Cable used Computer 10BASE-T port X setting Cat. 3, 5 straight UTP 10BASE-T hub port (I type) X setting Cat. 3, 5 straight UTP 10BASE-T hub port (X type) I setting Cat.
3.3 10/100BASE-TX Switched Ports This section applies to the 10/100BASE-TX Port #9 and expansion slot Port #10 pre-configured with a 10/100BASE-TX port module.
3.4 100BASE-FX Module The 100BASE-FX port module supports a connection to a Fast Ethernet network segment through a fiber optic connection. The module comes with two ST connectors. One labeled Tx is used for transmission. The other one labeled Rx is used for reception.
4. LED Indicators 4.1 LED Panel The switch provides comprehensive LED indicators for diagnosing and monitoring the operation of the unit as illustrated below: Figure 4-1 LED Indicators 4.2 Interpretation One Power LED indicates the status of the power supplied to the switch.
デバイスKTI Networks 2028の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
KTI Networks 2028をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKTI Networks 2028の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。KTI Networks 2028の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。KTI Networks 2028で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
KTI Networks 2028を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKTI Networks 2028の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、KTI Networks 2028に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKTI Networks 2028デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。