KunzメーカーMR55Bの使用説明書/サービス説明書
ページ先へ移動 of 21
57” ROUGH CUT MR55K MR55B OWNER’S MANUAL For Models: MR55T, MR55B-17. 5HP, MR55B-22-23HP & MR55K KUNZ ENGINEERING, INC. 42 / PH (815) 53 9-6954 1/09 With Assembly Instructions / MENDOTA, IL 61.
SAFETY INTRODUCTION Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided oper ating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others.
IMPORTANT SAFETY INFORMATION WARNING: Do not allow anyone to operate this equipment who has not fully read and comprehended the safety manual and who ha s not been properly trained in the safe operation of the equipment. WARNING: Operator should be familiar with all func tions of the unit.
SAFETY SIGNS AND LOCATIONS Clean or R Mendota, IL eplace Any Safety Signs That Are not Readable or Damaged Replacement decals can be purchased from your local dealer or Kunz Engineering Inc.
ASSEMBLY INSTRUCTIONS Read the complete assembly instructi ons before starting the assem bly. You should have: - one mower deck assembly - two carrier arm assemblies - two rear tire assemblies - one ATV tongue assembly A. ASSEMBLY OF MOWER WHEELS 1. Set the mower deck assembly on wood blocks so that it is suspended off the ground.
Figure 1: Rear Tire Assembly Installation Rear Tire rrier Arm sembly Ca As Figure 2: Assembly of Carrier Arm Assy., Hitch Pivot, and Tongue Rear Tire As Carrier Arm A Direct Behind Position Offset Position sy. (Attach on outside for both left and right sides) Pivot Arm ssy.
Figure 3: ATV Tongue Assembly TIONS AND ADJUSTMENTS OPERA indicate safety instructions. Follow injury and/or property damage. This safety alert symbol is used to these instructions to avoid personal w.
The tongue is equipped with a screw pin shackle clev is to provide movement in all directions on rough uneven ground. To prev rati on or debris, place the screw pin through the tow vehicle hitch and clev is and turn the screw pin until snug. The tongue is designed to adjust from left to right within the hitch pivot.
The cutting height can be adjusted in a range from 2. 0" to 8.0". This is accomplished by turning the height adjust cranks on bot h sides of the mower. See Figure 5 . Turn the cranks clockwise to raise the mower cutting height and counter-c lockwise to lower the mower cutting height.
C. STAR : Set parking brake on tow vehicle. Tur on the underside of the gas tank. Set Set the th Start engine and allow engine to warm up. Set engine tch handle. (The clutch handle is located at the front of the mower under the engine.) CAUTION: If the rough cut mower from the uncut area before attempting to engage the clutch .
WARNING: Remove all objects from the work area that might be picked up and thrown by WARNING: Do not mow when child ren and others are around. WARNING: Do not fill fuel tank wh ile engine is running or hot. WARNING: Keep all safety shields and defle ctors in place during operation.
F. DRIVE aking any adjustments or repairs. Remov Loosen the nuts on the spring-loaded idler; adjust bol t until the belt can be slipped off the idler and h Slip the belt down under the drive sheav e and off the blade spindle sheaves. Install the new belt and then adj ust the tension as follows: See Figure 7.
provide the appropriate braking force. If the spri ng length is to long it will be necessary to adjust the brake stud closer to the belt. If the spring length is to short it will be necessary to adjust the brake stud further away from t he belt.
G. Sharp blades can cause bodily in jury if not handled properly. pened. Out of b bolts co CAUTION: Always properly tighten the blade bolts to the specified torque. Failure to do so can lead to saddle. The Models MR55K, MR55B and MR55T use the K unz Engineering Part # (202141) blade bolt.
ACREASE ROUGH CUT MOWER SPECIFICATIONS Model Model Model Mode l MR 55B-17.5H P MR 55B-22-23H P MR 55K MR55 T EN NE: GI En En Cy 2 2 Cycles Cran ksha ft Engine HP Bore 3.56” 3.57" 2.97" 3.03" St Di Oil 1.94 U. S. qt 1.5 U. S. qt 2 U.S.
ACREASE ROUGH CUT MOWER PARTS LIST It e m Pa rt # De sc rip t i o n Quanti t y 1 2 140 21 Cu p W as h er 6 2 2 160 02 W ir e Lo ck P i n, . 3 1" x 2 . 50 " 2 3 2 160 09 S c re w P in S ha c k l e C lev i s 1 4 2 220 05 W or m D r iv e Hos e C la m p ( 7- 7/ 8" t o 9 - 1/ 8" Cl a m pi ng Di a.
It e m Pa rt # De sc rip t i o n Quanti t y 3 1 6 001 89 I d l er S pac er Bl oc k 1 3 2 9 000 23 Co nt r o l P anel 1 3 3 9 0 0 04 9 Ba tt e ry Bo x A ssy. 1 3 4 9 000 58 Hi t c h P iv ot 1 3 5 9 000 61 P i v o t A r m 4 3 6 9 000 62 Hei g ht Ad ju s t Nu t 2 3 7 9 000 63 Cl ut c h A r m 1 3 8 9 000 65 I d l er A r m A ss y .
U ACREASE ROUGH CUT MOWER PARTS 10 2 3 4 5 6 7 8 9 1 11 12 13 16 14 15 17 19 20 21 22 23 25 26 27 28 29 30 41 24 32 33 34 35 36 38 39 40 44 45 43 42 31 18 37 17.
OPTIONAL EQUIPMENT OPTIONAL WETLANDS KIT The optional wetlands kit features an extra set of tires for added ground supp ort in soft or water saturated areas. The following are applications and features that the wetlands kit works best in. • Great for wetlands or marshy area s that stay wet all year around.
OPTIONAL EQUIPMENT OPTIONAL ELECTRIC LIFT KIT The optional electric lift kit consists of all of t he mounting hardware, bracke ts, electric actuator and wiring with remote control panel. • Great for constantly changing te rrain and grass/brush heights.
OPTIONAL EQUIPMENT OPTIONAL FLOATATION KIT The optional floatation kit consists of one additi onal front and rear tire, mounting brackets and hardware.
デバイスKunz MR55Bの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Kunz MR55Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKunz MR55Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kunz MR55Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kunz MR55Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kunz MR55Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKunz MR55Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kunz MR55Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKunz MR55Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。