KustomメーカーKUSTOM KHS-6640の使用説明書/サービス説明書
ページ先へ移動 of 14
KHS-6640 INSTALLATION MANUAL SMARTHOME.COM™ 1-800-SMART-HOME 949-221-9200 http://www.smarthome.com Order #8270C.
KUSTOM SIX-ZONE AMPLIFICATION SYSTEM MODEL KHS6640 A.) Power Switch - Left on, the KHS6640, when not being used, will go into a “ sleep ” mode, ready to turn back on when an input signal is applied from any of the six sources. In the off position, the unit w ill not function.
OUTPUT SECTION - 1.) Line Outputs (Left & Right) - these are dual RCA line outputs to go to additional amplifiers or to powered sub-woofers. The white one is for left channel and the red one is for right channel. These outputs will react to the volume controllers for each zone.
CONTROLLER SECTION 7.) Master IR Output - this connector allows the “ party ” mode to apply to multiple units if additional units are added. 8.) Master IR Input - this is for the “ party ” mode controller. This controller should be located near the unit and sources.
INFRARED (IR) SECTION 16.) Source Output #I - this q/8 ” 2 conductor jack is from the IR emitters and are “ locked ” source specific. This is useful in the instance, if you have 2 or more of the same brand CD player, since the same IR command will work on both, this ONLY sends the IR command to this particular source.
Master In/Out: The master controller input will accept a seventh KHSGS controller. This controller will then become a master control for the entire system. If “ Source 1 ” is selected on this controller, all zones will switch to Source 1. If volume up is pressed, all zones will go up and visa versa volume down will lower all zones.
KHS 6640 Installation Manual Recommended Cables: Category-5 or Category-3 (4 twisted pair stranded), shielded or unshielded. 164 or (2) 16-2 speaker cables. To keep the installation process as simple as possible for first time users, please follow these simple steps.
KHS-6S CONTROLLER 1.) IR Sensor 2.1 3.) 4.1 5.1 6.1 Source Selectors (1 - 6) Source LED ( 1 - 6) Power Status LED Mute Button Volume Up 7.) Volume Down 1.) IR Sensor - this is an Infrared Sensor window. We suggest you aim the external remote control directly at this window to pass on commands back to and through the unit.
84 Reset Clear KHS-6D CONTROLLER The left side of this controller is identical to the KHS-6S consult last page. ” I 16.) 17.) 18.) 19.) 20.) 21.) 22.) Numeric Entry Enter Button Macro Button Skip Backwards Skip Forwards Power On Reverse 14.) Learn Button ‘ x”.
I This pacle is for information onlv - Consult Your Installer for Application 1 IR Emitter Modulation Frequency - these are factory set to give optimum preformance of the emitters. Factory setting is 40KHz. Range is 32 KHz full CCW to 65 KHz full CW. IR OUTPUT PC BOARD (Fig.
KHS-6D CONTROLLER (cont ’ dl 16.) Numeric Entry Keys (0 - 9) - depending on the mode you are in these keys will allow direct track access on a CD, an individual station on n/ or DSS, or a station on a tuner, etc. If you are in the macro mode, these will allow direct access to your stored macros.
Programming the KHSGD Controllers The KHSGD controller is designed to learn and store IR codes for virtually any piece of audio/video equipment. This enables the individual programming and use of multiple functions for all of your source components. Programming Individual Functions 1) Press the “ learn ” button on the controller.
MACRO PROGRAMMING The KHS-6D has 16 programmable macro memories. It will automatically transmit a series of 20 commands deep. To enter the macro mode - press macro and the either the 0 through 9 buttons OR the device source keys (l-6). You can insert a delay time from 1 to 99 seconds between steps (the default is 5 sec.
dendum 1. 2. 3. 4. 5. 6. 7. Programming a wireless remote using the KHS6S Wall Controller Remove the Decora cover plate, and controller face plate. Place your wireless remote in learn mode. (learn LED should begin flashing on the KHSLRC model learning remote control) Select the device bank button to program (i.
デバイスKustom KUSTOM KHS-6640の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kustom KUSTOM KHS-6640をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKustom KUSTOM KHS-6640の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kustom KUSTOM KHS-6640の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kustom KUSTOM KHS-6640で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kustom KUSTOM KHS-6640を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKustom KUSTOM KHS-6640の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kustom KUSTOM KHS-6640に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKustom KUSTOM KHS-6640デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
