Lennox Hearthメーカー33/40 DV INSの使用説明書/サービス説明書
ページ先へ移動 of 38
Report No. 050-F-22-5 INST ALLA TION AND OPERA TION MANUAL Direct-V ent Gas Fireplace Heater Inserts Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. WHA T TO DO IF YOU SMELL GAS: • Do not light any appliance.
2 1. FOR YOUR SAFETY do not install or operate your fireplace insert without first reading and understanding this manual. Any installation or operation of the appliance deviating from that which is stated in this manual WILL void the warranty and may be hazardous.
3 C O N G R A TU LA T I O N S O N T H E P U R C H A S E O F Y O U R N E W G A S A P P L I A N C E M A N U F A C T U R E D B Y L E N N O X H E A R TH P R O D U C T S .
4 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Millivolt Models with Manually-Modulated Gas Valves Natural Gas Propane (LP) Gas Model Input Rate (BTU/HR) Input Rate (BTU/HR) SHR33 19,500 to 33,000 19,500 to 33,000 SHR40 24,000-40,000 21,500 to 37,500 T able 1 No te: T h es e ap p l ia nce s ar e de s i gn ed a s su p p le men tal h e at ers .
5 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Manufactured Home Installations - These appliances must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 .
6 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Note: The following requirements reference various Massachusetts and national codes not contained in this document.
7 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Figure 1 Front View Side View T op View Insert Dimensions Inches (millimeters) A Left front of unit to center line 13-1/8 (333) B Right front of un.
8 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE A B C D E F G H I C L Figure 2 - Existing Fireplace Minimum Dimensions Figure 3 - Minimum Clearances Co m bu sti b le s T rim or Ma n t el De p t h.
NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE W ARNING THIS FIREPLACE HAS BEEN AL TERED TO ACCOMMODA TE A FIREPLACE INSERT AND SHOULD BE INSPECTED BY A QUALIFIED PERSON PRIOR TO RE-USE AS A CONVENTIONAL FIREPLACE.
10 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Vertical Cap T ermination Connector Exhaust Intake Combustion Air Intake Venting Requirements Approved Vent Systems: Len nox He art h Pr odu cts C o-l ine ar Chi mne y L ine r K it Rec omm ende d: • The Flex Kit, Cat.
11 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Vertical V enting The vent pipes must be connected to the proper collars on the unit and the exhaust vent pipe must be connected to the termination cap or the unit will not operate.
12 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE T ools Needed: No tools are needed Cat. No. Description H5746 Shoreline Door Assembly (Figure 9) 1. Locate three tabs on the bottom of the door . These tabs will go into the tab slots along the bottom of insert.
13 4. Slide the top panel in place with the detailed side down. Make sure panel is positioned all way back and resting on side panels. T op panel should be flush in front with the side panels. See Figure 18 . 3. Position and slide the side panels against the rear panel.
14 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE A C D E F B G A Lo g s upp o rt s A B C D E T o Install Log Set: 1. Open the box and carefully remove and identify the different items. Start with the rear log (A). Set it down on the log supports located on the left rear of firebox.
15 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE 2. Separate the glowing embers (F) into quarter size pieces and place along ports on burner pan. DO NOT cover burner secondar y holes on burner pan. The pattern for the glowing embers should be similar to what is shown in Figure 22 .
16 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE 2 Slide the insert into its final location in the fireplace. In case of uneven wall sur face open the right surround access door and make any adjustments needed to ensure there is enough clearance to open the access door (see Page 17 ).
17 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE T ools Needed: 7/16” wrench Flat End Screwdriver Adjustment Procedure: Step 1 Open the surround access door . Inspect the tension or lack of tension while opening the door to determine if it should open easier or tighter .
18 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE W e r ec omm end t ha t a qu al ifie d i n di vid ual s uc h as a pl u m b er o r ga s fit te r be us ed to cor rec tly s i z e an d ro u t e th e gas s u p pl y lin e to th e ap p l ia nce .
19 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE T o T urn Off Gas T o Appliance 1. T urn off th e “O N/O FF” ro cke r s wit ch and /or th erm ost at (if ins tal led ). 2. T urn off el ectr ic pow er to the ap pli anc e i f s ervic e i s t o b e p erfor med .
NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Flame Appearance and Sooting Y our Shoreline™ fireplace insert is designed for maximum heating efficiency . Therefore, upon lighting of the main burner the flames will be semi-transparent or “bluish.
21 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Blower Operation Y our Shoreline gas insert comes equipped with a 150 CFM blower with a variable speed control and an automatic temperature activated On/Off snap switch. 1. Plug the blower power cord into a grounded (three-prong) outlet.
22 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Shoreline™ Main Burner Operation Y our Shoreline fireplace insert comes with an “ON/OFF” rocker switch used to turn the burner on and off while the pilot is on. The rocker switch is located in the control panel above the blower rheostat switch and to the left of the igniter .
23 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Maintenance Checklist The following should only be performed by a qualified service techni- cian. 1. Annual inspection should be made and the following checks performed: p When unit is cool, remove glass and inspect burner for dirt, soot, and lint accumulations, and remove if necessary .
24 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Do not remove the glass door while the insert is hot. T o remove the glass door , pull for ward and up on the top latches. Lift the glass door up and off the lower spring latch. Be careful not to damage or scratch the glass while handling.
25 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE MAINTENANCE T ASK ACCOMPLISHING PERSON PROCEDURE Inspecting/Cleaning Burner , Logs and Controls Qualified Service T echnician Inspect valve and ensure it is properly operating. Check piping for leaks.
26 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE NOTE: When troubleshooting the gas control system, be sure the external gas shut off valve, located at the gas supply inlet is in the “ON” position. IMPORT ANT : Call your gas supplier or plumber for additional help with any gas control problem.
27 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Item # Part/Cat. No. Description 1 H5722 Firebox Assembly 2 H5723 Air Intake Assembly 3 H5724 Blower Box Assembly w/blower 4 H5725 Flue Collar Ass.
28 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE 24 23 3 30 2 24 1 23 27 27 2 30 2 4 5 25 2 30 P AR T IDENTIFICA TION Item # Description 1 Firebox Assembly 2 Air Intake Assembly 3 Blower Box Asse.
29 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Pil ot Cas se tte As sem bl y 13 12 30 11 10 9 12 30 15 14 Item # Description 9 Pilot Assembly w/Shield 10 Main Orifice 11 Bulkhead Assembly 12 C.
30 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE 6 3 2 29 27 6 7 8 P AR T IDENTIFICA TION Item # Description 2 Air Intake Assembly 3 Blower Box Assembly w/Blower 6 Rear Leveling Leg Assembly 7 Ou.
31 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE 21 29 8 16 17 20 18 19 20 22 Ceramic Log Set Item # Description 8 Burner Assembly 16 Louver Assembly 17 Blower Rheostat 18 Control Panel/Valve Cov.
32 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE 36/37 34/35 31 33 32 36/37 36/37 34/35 33 32 31 32 33 38/39 34/35 38/39 38/39 38/39 4-Piece Surround Assembly 3-Piece Surround Assembly Item # Des.
33 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE OPTIONAL ACCESSORIES Standard Remote Control System The Model RCL (Standard) Remote Control System, features a simple On/Off control function for the insert.
34 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE Refractory Brick Panel Set (6 pieces) These decorative brick panels sets are offered in 3 attractive styles. One set required. Surround Kits These surround panels install around the insert body providing an attractive finished look.
35 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE 4 G e a r cl a m p s S i d e V i ew o f C a p Ca p ha s tw o 3 " co ll ar s fo r at ta ch me nt of l in er s T erm in a ti on Ca p Fl as hi ng T e rm i n a t i o n K i t, D V I C a t.
36 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE SAFETY / LISTING LABEL.
37 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE LIGHTING INSTRUCTIONS LABEL.
Printed in U.S.A. © Lennox Hearth Products 2008 P/N 850,050M REV . C 01/2008 Lennox reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.
デバイスLennox Hearth 33/40 DV INSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lennox Hearth 33/40 DV INSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLennox Hearth 33/40 DV INSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lennox Hearth 33/40 DV INSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lennox Hearth 33/40 DV INSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lennox Hearth 33/40 DV INSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLennox Hearth 33/40 DV INSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lennox Hearth 33/40 DV INSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLennox Hearth 33/40 DV INSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
