Lennox HearthメーカーF50の使用説明書/サービス説明書
ページ先へ移動 of 25
IMPRESSA F50/F5/F505 Instructions for use 11/05 Art. Nr. 65691.
Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Consiglio JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig.17 1 2 3 Fig. 5 Fig. 16 B.
Control elements 1. Rotary Switch 2. Illuminated ring 3. ON/OFF key 4. Programming key 5. Draw-off key 1 cup 6. Draw-off key 2 cups 7. Maintenance key 8. Steam pre-selection key 9. Display dialog system 10. Water tank with carrying handle 11. Filler funnel for pre-ground coffee: 12.
5 Contents 1. Safety information .......................................... page 6 1.1 Warning .............................................. page 6 1.2 Precautions .......................................... page 6 2. Preparing the IMPRESSA ..........
6 Introduction Thank you for purchasing the IMPRESSA. To ensure perfect func- tioning of your IMPRESSA, carefully read this operating manual and keep it for future reference.
7 2.3 Fill water tank Only use fresh, cold water. Never fill in milk, mineral water or other liquids. Remove the water tank and rinse it with cold tap water thoroughly (Fig. 4). Then fill the water tank and reinstall it. Make sure to install the tank properly, it must engage audibly.
8 FILLING SYSTEM CLOSE TAP Close the steam / hot water draw-off tap (14). HEATING PRESS RINSE Press the maintenance key (7). Machine carries out a rinsing operation. RINSING READY If BEANS FILL is displayed, press the coffee draw-off key again.
9 5. Installation of Claris plus filter cartridges If the Claris plus filter cartridge is installed properly, de-scal- ing of the coffee machine is no longer required. For more information on the Claris plus filter cartridge refer to brochure «Claris plus.
10 6. Rinsing the IMPRESSA When the IMPRESSA is switched off and has cooled down, a rinsing operation is started when the machine is switched on again. When the machine is switched off, a rinsing oper- ation is started automatically. Switch on the IMPRESSA using the ON/OFF key (3).
11 tank. Make sure that the pre-ground you use is not too fine. This may cause blocking of the system. In this case the coffee only drips out of the coffee spout. If you have filled in too little powder, the message ADD MORE POWDER will be displayed. The IMPRESSA stops the operation and returns to "ready for draw off" mode.
12 11. Drawing off hot water If you do not change the settings using the Rotary Switch (1), the water quantity last adjusted will be drawn off auto- matically.
13 STEAM READY To draw off steam, open the steam/hot water draw-off tap (14) (Fig. 13). The illuminated ring (2) is active. You can adjust the steam draw-off time individually by turning the Rotary Switch (1) until the required SEC are displayed.
14 13.3 Cleaning the Professional-Cappuccino Frother The Professional-Cappuccino Frother must be cleaned after each draw-off operation. Fill water in a container and immerse the hose in it. Draw off steam until the water/steam mixture is clean.
15 Turn the Rotary Switch (1) until Aroma is displayed. AROMA Press the Rotary Switch (1). ROBUST Turn the Rotary Switch (1) until the following message is dis- played: STANDARD To confirm the new aroma settings, press the Rotary Switch (1).
16 If the machine is disconnected from power supply, the time must be programmed again. 15.6 Programming the automatic switch-on time You must programme the time (Chapter 15.5) if you want to use the automatic switch-on function. READY Press programming key (4) until FILTER appears.
17 READY Press programming key (4) until FILTER appears. The illuminated ring (2) is active. Turn the Rotary Switch (1) until CUPS MADE is displayed. CUPS MADE Now press the Rotary Switch (1) to start programming the item CUPS MADE The total number of drawn off products is displayed.
18 Press the programming key (4) to quit the programming mode or select the next programming item using the Rotary Switch (1). READY 15.11 Programming the display for ML/OZ READY Press the Rotary Switch (1) until FILTER – / appears The illuminated ring (2) is active.
19 16.4 Fill coffee beans FILL BEANS Refill beans as described in Chapter 2.4. The message REFILL BEANS will disappear after you draw off your next cup of coffee. We recommend that you clean the bean tank regularly before refilling beans, using a dry cloth.
20 16.9 Emptying the system Precondition: IMPRESSA switched off This operation is required to protect the IMPRESSA against frost damage during transports.
21 18. De-scaling Your IMPRESSA features an integrated de-scaling program. The de-scaling operation will take some 40 min. JURA de-scaling tablets wich are specially designed for the de-scaling program of your IMPRESSA are available at your authorized dealer.
22 20. Tips for perfect coffee Height-adjustable coffee spout (17) You can adjust the height of the coffee spout to the size of your cups (Fig. 3) Grinding degree Refer to Chapter 2.5 «Adjusting the grinding gear». Preheating cups You can preheat the cups using hot water or steam.
23 21. Messages Cause Remedy FILL WATER Water tank is empty. Refill water Float defective Rinse or de-scale water tank FILL BEANS Bean tank is empty. Refill beans Although you have refilled beans, the Draw off a cup of coffee. The message will message still appears.
24 22. Problems Problem Cause Remedy Very loud noise coming from the Foreign body in grinding gear Drawing off pre-ground coffee still possible grinding gear Have IMPRESSA checked by JURA Service Too .
25 23. Legal information These operating instructions contain all the information required for using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance.
デバイスLennox Hearth F50の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lennox Hearth F50をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLennox Hearth F50の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lennox Hearth F50の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lennox Hearth F50で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lennox Hearth F50を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLennox Hearth F50の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lennox Hearth F50に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLennox Hearth F50デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
