Lenovoメーカー4158の使用説明書/サービス説明書
ページ先へ移動 of 270
ThinkStation Har dwar e Maint enance Manual Machine T ype: 4105, 4155, 4157, 4158, 4217, 4218.
.
ThinkStation Har dwar e Maint enance Manual Machine T ype: 4105, 4155, 4157, 4158, 4217, 4218.
Note: Before using this information and the pr oduct it supports, be sur e to read the information under Appendix A “Notices” on page 255. T welfth Edition (March 2012) © Copyright Lenovo 2008, 2012.
Contents Chapter 1. About this manual . . . . . . 1 Important Safety Information . . . . . . . . . . 1 Important information about replacing RoHS compliant FRUs . . . . . . . . . . . . . . . 1 Chapter 2. Safety information . . . . . . 3 General safety .
Chapter 9. Symptom-to-FRU Index . . 53 Hard disk drive boot err or . . . . . . . . . . 53 P ower Supply P roblems . . . . . . . . . . . 53 Diagnostic error codes . . . . . . . . . . . 54 Beep symptoms . . . . . . . . . . . . . . 71 POST err or codes .
Automatic congur ation and power interface (ACPI) BIOS . . . . . . . . . . . . . . 253 Automatic P ower -On featur es . . . . . . . 253 Appendix A. Notices . . . . . . . . . 255 T elevision output notice . . . . . . . . . . . 256 T r ademarks . . .
vi ThinkStation Hardware Maint enance Manual.
Chapter 1. About this manual This manual contains service and refer ence information for ThinkStation™ computers list ed on the cover . It is int ended only for tr ained servicers who are familiar with L enovo® computer pr oducts. Before servicing a L enovo pr oduct, be sure to read the Safety Information.
be noncompliant, but in all cases, if the parts are compliant, the r eplacement parts must also be compliant. Note: RoHS and non-RoHS FRU part numbers with the same t and function ar e identied with unique FRU part numbers.
Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with befor e servicing a computer . General safety F ollow these rules to ensure gener al safety: • Observe good housekeeping in the ar ea of the machines during and after maintenance.
Important: Use only appr oved t ools and test equipment. Some hand tools have handles cover ed with a soft material that does not insulat e you when working with live electrical currents. Many customers have, near their equipment, rubber oor mats that contain small conductive bers t o decr ease electrostatic dischar ges.
V oltage-selection switch Some computers are equipped with a voltage-selection switch located near the power -cord connection point on the comput er . If your comput er has a voltage-selection switch, ensur e that you set the switch to match the voltage available at your electrical outlet.
5. Check for any obvious alter ations. Use good judgment as to the safety of any alter ations. 6. Check inside the unit for any obvious unsafe conditions, such as metal lings, contamination, water or other liquids, or signs of re or smoke damage.
• F r ench • German • Hebr ew • Italian • Kor ean • Spanish DANGER Electrical curr ent fr om power , t elephone and communication cables is hazar dous. T o avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or recongur ation of this product during an electrical storm.
CA UTION: When laser products (such as CD-ROMs, DVD-ROM drives, ber optic devices, or transmitters) are installed, not e the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser r adiation.
Chapter 2 . Safety information 9.
≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) 1 2 PERIGO 10 ThinkStation Hardware Maint enance Manual.
A corrent e elétrica pr oveniente de cabos de alimentação, de telefone e de comunicações é perigosa. P ara evitar risco de choque elétrico: • Não conecte nem desconecte nenhum cabo ou e xecute instalação, manut enção ou recongur ação deste pr oduto durant e uma tempestade com raios.
• Não r emova as tampas. A r emoção das tampas de um produt o a laser pode resultar em exposição prejudicial à r adiação de laser . Não exist em peças que podem ser consertadas no int erior do dispositivo.
Chapter 2 . Safety information 13.
1 2 14 ThinkStation Hardware Maint enance Manual.
Chapter 2 . Safety information 15.
1 2 DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de tr ansmission peut pr ésenter un danger . P our éviter tout risque de choc électrique : • Ne m.
Connexion Déconnexion 1. Mett ez les unit és HORS TENSION. 2. Commencez par brancher tous les cor dons sur les unités. 3. Br anchez les câbles d'interface sur des connecteurs. 4. Br anchez les cordons d'alimentation sur des prises. 5. Mett ez les unit és SOUS TENSION.
≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) A TTENTION: Soulevez la machine avec précaution. A TTENTION: L'interrupteur de contrôle d'alimentation de l'unité et l'interrupteur dubloc d'alimentation ne coupent pas le courant électrique alimentantl'unité.
• Die V erbindung zu den angeschlossenen Netzkabeln, T elek ommunikationssystemen, Netzwerk en und Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- und Kongur ationsproz eduren k eine anders lautenden Anweisungen enthalten sind.
Laserstrahlung bei geöffneter V erkleidung. Nicht in den Strahl blicken. K eine Lupen oder Spiegel verwenden. Strahlungsbereich meiden. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten.
Chapter 2 . Safety information 21.
1 2 PERICOL O La corrent e elettrica provenient e dai cavi di alimentazione, del telefono e di comunicazione può essere pericolosa. P er evitare il rischio di scosse elettriche: • Non collegare o scollegare qualsiasi cavo oppure effettuar e l'installazione, la manutenzione o la ricongurazione del pr odotto durante un tempor ale.
• Se possibile, utilizzar e solo una mano per collegare o scollegar e i cavi di segnale. • Non accender e assolutamente appar ecchiature in presenza di incendi, perdite d'acqua o danno strutturale.
PERICOL O Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. T ener presente quant o segue: Aprendo l'unità vengono emesse radiazioni laser . Non ssare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l'esposizione al fascio.
Chapter 2 . Safety information 25.
1 2 PELIGRO La corriente eléctrica pr ocedente de cables de alimentación, teléfonos y cables de comunicación puede ser peligrosa. Par a evitar el riesgo de descarga eléctrica: • No conecte ni desconecte los cables ni r ealice ninguna tarea de instalación, mantenimiento o reconguración de este producto dur ante una tormenta eléctrica.
• Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y los módems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique lo contrario en los procedimientos de instalación y conguración.
Algunos product os láser tienen incorporado un diodo láser de clase 3A o clase 3B. T enga en cuenta lo siguiente: Cuando se abre, queda e xpuesto a radiación láser . No mire dir ectamente al rayo láser , ni siquiera con instrumentos ópticos, y evite e xponerse directamente al rayo láser .
Chapter 3. Gener al information This chapter pr ovides gener al information that applies to all machine types supported by this publication. Lenovo W elcome Center The Lenovo W elcome progr am introdu.
F or machine types 4105, 4157, and 4217. This section lists the physical specications for your comput er . Dimensions Width: 175 mm (6.9 inches) Height: 478 mm (18.8 inches) oor to t op of handle Depth: 460 mm (18.1 inches) Weight Maximum congur ation: 16.
• Air temper ature: Operating at 0 - 3000 ft (914.4 m): 10° t o 35°C (50° to 95°F) Non-operating: -10° to 60°C (14° to 140°F) • Humidity: Operating: 10% to 80% (10% per hour) Non-operating: 10% to 90% (10% per hour) T r ansit: 10% t o 90% (10% per hour) • Maximum altitude: 7000 ft (2133.
32 ThinkStation Hardware Maint enance Manual.
Chapter 4. Gener al Check out Attention The drives in the computer you are servicing might have been rearr anged or the drive startup sequence changed. Be e xtremely car eful during write oper ations such as copying, saving, or formatting. Data or progr ams can be overwritten if you select an incorr ect drive.
– Has this conguration ever worked? – If it has been working, what changes wer e made prior t o it failing? – Is this the original r eported failure? • Diagnostics version – T ype and ver.
Chapter 5. Diagnostics Diagnostic pr ograms are used to test hardwar e components of your comput er . Diagnostic pr ograms can also r eport operating-syst em-controlled settings that interfer e with the corr ect oper ation of your syst em.
PC-Doctor for Windows PE The PC-Doctor for Windows PE diagnostic progr am is part of the Rescue and Recovery workspace on each Lenovo computer . Use PC-Doctor for Windows PE if you ar e unable t o start the Windows operating syst em or if L enovo ThinkV antage T oolbox has not been successful in isolating a possible pr oblem.
2. Insert the disc into the optical drive. 3. Restart the computer . Note: If the diagnostic pr ogram does not start, you might not have your optical drive set as a startable device. See “Selecting a startup device” on page 43 for instructions on how t o change the startup device.
T est r esults (N/A, P ASSED , F AILED , ABORTED) are displayed in the eld beside the t est description and in the test log. See “Viewing the test log” on page 39. T o select one or more t ests, use the following procedur e. 1. Open the corr esponding test category .
• P erforms all the steps in Quick Er ase. • P rovides a DOS utility that writ es r andom data t o all sect ors of the hard drive. • P rovides an estimate of time to completion along with a visual repr esentation of completion status. • P rovides messages that warn the user about non-recover able process.
40 ThinkStation Hardware Maint enance Manual.
Chapter 6. Using the Setup Utility The Setup Utility pr ogram is used to view and change the congur ation settings of your computer , regar dless of which operating syst em you ar e using. However , the oper ating-system settings might override any similar settings in the Setup Utility progr am.
• Not be your name or your user name • Not be a common word or a common name • Be signicantly differ ent from your pr evious password User P assword When a User Passwor d is set, the comput er cannot be used until a valid password is typed fr om the keyboard.
Note: If you do not want to save the settings, select Exit the Setup Utility without saving . T o set the L egacy diskette A, do the following: 1. S tart the Setup Utility progr am (see “Starting the Setup Utility progr am ” on page 41). 2. F rom the Setup Utility pr ogram menu, select Devices ® Legacy diskette A .
Exiting from the Setup Utility progr am After you nish viewing or changing settings, pr ess Esc t o return to the Setup Utility pr ogram menu (you might have t o pr ess Esc sever al times). If you want t o save the new settings, select Save Settings or Save and e xit the Setup Utility .
Chapter 7. Installing hard disk drives and conguring RAID (types 4105, 4157, 4217) This chapter contains information about installing hard disk drives and conguring Redundant Arr ay of Independent Disks (RAID) for this pr oduct. Note: The information about conguring RAID in this chapter is applicable only for a Windows environment.
Creating RAID volumes This section describes how t o use the Intel Matrix Stor age Manager option ROM congur ation utility to creat e RAID volumes. 1. P ress Ctrl+I when pr ompted to ent er the Int el Matrix Stor age Manager option ROM conguration utility .
• RAID Level 0 – Striped disk arr ay – T wo hard disk drives minimum – Better performance without fault toler ance • RAID Level 1 – Mirrored disk array – T wo hard disk drives minimum .
Conguring the Marvell BIOS Setup to set an optional hot spare hard disk drive T o congur e the Marvell BIOS Setup to set an optional hot spare hard disk drive: 1. T urn on your computer and press Ctrl+M when prompted t o enter the Marvell BIOS Setup.
Chapter 8. Installing hard disk drives and conguring RAID (types: 4155, 4158, 4218) This chapter contains information about installing hard disk drives and conguring Redundant Arr ay of Independent Disks (RAID) for this pr oduct. Note: The information about conguring RAID in this chapter only applies for a Windows environment.
Conguring the Marvell BIOS Setup to enable SA T A or SAS RAID 0, 1, 5, or 10 functionality T o enable SA T A/SAS RAID functionality, use the Marvell BIOS Setup conguration utility as the SA T A/SAS conguration utility . This utility assumes that the system has the r equired number of hard disk drives.
2. On the Marvell BIOS Setup screen, use the arr ow keys t o select RAID Cong and press Enter . The RAID Cong menu opens. 3. F rom the RAID Cong menu, select Delete arr ay . 4. Use the arr ow keys and the Ent er key to select the arr ay you want to delet e fr om the list.
52 ThinkStation Hardware Maint enance Manual.
Chapter 9. Symptom-t o-FRU Inde x The S ymptom-to-FRU index lists error sympt oms and possible causes. The most likely cause is list ed rst. Always begin with Chapt er 4 “General Checkout” on page 33 . This inde x can also be used t o help you decide which FRUs to have available when servicing a computer .
Diagnostic err or codes Refer to the following diagnostic err or codes when using the diagnostic tests. See “Running tests” on page 37 for the specic type for information about the Diagnostic pr ograms. In the following index, X can repr esent any number .
Diagnostic Error Code FRU/Action 000-197-XXX BIOS test warning 1. Mak e sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility” on page 41 2. Re-run test 3. Replace the component that is called out in warning statement 4.
Diagnostic Error Code FRU/Action 001-038-XXX System Extension failure 1. Adapter card 2. Syst em board 001-039-XXX Syst em DMI data structur e error 1. Flash the system. See “Flash update procedures” on page 251 2. Syst em board 001-040-XXX System IRQ failure 1.
Diagnostic Error Code FRU/Action 001-273-XXX Syst em IRQ6 (diskette drive) failure 1. Disk ette Cable 2. Diskett e drive 3. Syst em board 001-274-XXX System IRQ7 failure 1. Device on IRQ7 2. Syst em board 001-275-XXX System IRQ8 failure 1. Device on IRQ8 2.
Diagnostic Error Code FRU/Action 005-016-XXX Video Simple P attern test failure 1. Video Ram 2. Video car d, if installed 3. Syst em board 005-024-XXX Video Addressing test failur e 1. Video card, if installed 2. Syst em board 005-025-XXX Video Checksum V alue error 1.
Diagnostic Error Code FRU/Action 005-2XX-XXX 005-3XX-XXX Video subsystem err or 1. Video card, if installed 2. Syst em board 006-000-XXX Diskett e interface T est Passed No action 006-0XX-XXX Diskette interface err or 1. Diskette drive Cable 2. Diskett e drive 3.
Diagnostic Error Code FRU/Action 011-196-XXX Serial port test halt, err or threshold ex ceeded 1. P ress F3 to r eview the log le 2. Re-start the test to r eset the log le 011-197-XXX Serial port test warning 1. Mak e sure the component that is called out is connected and/or enabled.
Diagnostic Error Code FRU/Action 014-197-XXX P arallel port test warning 1. Mak e sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility” on page 41 2. Re-run test 3. Replace the component that is called out in warning statement 4.
Diagnostic Error Code FRU/Action 015-196-XXX USB port test halt, err or thr eshold ex ceeded 1. P ress F3 to r eview the log le 2. Re-start the test to r eset the log le 015-197-XXX USB port t est warning 1. Mak e sure the component that is called out is connected and/or enabled.
Diagnostic Error Code FRU/Action 018-250-XXX PCI C ard Services err or 1. PCI card 2. Riser car d, if installed 3. Syst em board 020-000-XXX PCI Interface T est P assed No action 020-0XX-XXX PCI Interface error 1. PCI card 2. Riser car d, if installed 3.
Diagnostic Error Code FRU/Action 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure 1. IDE signal cable 2. Check power supply 3. Reseat IDE signal cable 4.
Diagnostic Error Code FRU/Action 030-196-XXX SCSI int erface test halt, error thr eshold ex ceeded 1. P ress F3 to r eview the log le 2. Re-start the test to r eset the log le 030-197-XXX SCSI interface t est warning 1. Make sure the component that is called out is connected and/or enabled.
Diagnostic Error Code FRU/Action 071-00X-XXX 071-01X-XXX 071-02X-XXX Audio port error 1. Run Setup 2. Flash the syst em. See “Flash updat e pr ocedures” on page 251 3. Syst em board 071-03X-XXX Audio port failure 1. Speakers 2. Micr ophone 3. Audio car d, if installed 4.
Diagnostic Error Code FRU/Action 080-197-XXX Game P ort int erface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility” on page 41 2. Re-run test 3. Replace the component that is called out in warning statement 4.
Diagnostic Error Code FRU/Action 086-199-XXX Mouse P ort interface test failed, cause unknown 1. See “Undetermined problems” on page 75 2. Flash the system and r e-test.
Diagnostic Error Code FRU/Action 170-199-XXX V oltage Sensor(s) test failed, cause unknown 1. See “Undetermined problems” on page 75 2. Flash the system and r e-test. See “Flash update procedur es” on page 251 3. Replace component under function t est 170-250-XXX 170-251-XXX V oltage Sensor(s) V oltage limit err or 1.
Diagnostic Error Code FRU/Action 201-XXX-XXX System Memory error 1. Replace the memor y module called out by the test 2. Syst em board 202-000-XXX Syst em Cache T est P assed No action 202-XXX-XXX System Cache err or 1. C ache, if removable 2. Syst em board 3.
Diagnostic Error Code FRU/Action 305-000-XXX Monitor DDC T est P assed No action 305-250-XXX Monitor DDC self test failure 1. Run Setup to enable DDC 2.
POS T error codes Each time you power -on the system, it performs a series of t ests that check the oper ation of the syst em and some options. This series of t ests is called the P ower-On Self- T est , or POS T . POS T does the following operations.
POST Error Message Description/Action Pr ess T AB to show POS T screen P ressing the T AB key permits the user to toggle between the default POS T display scr een and a custom POS T display scr een. Error: Non-System disk or disk err or Replace and press any k ey when ready The BIOS was unable to nd a suitable boot device.
Message/Symptom FRU/Action "Insert a Disk ette" icon appears with a known-good diagnostics diskette in the rst 3.5-inch diskett e drive. 1. System Board 2. Diskett e Drive Cable 3. Network Adapter Intensity or color varies from left t o right of char acters and color bars 1.
Undetermined problems If this computer has a parallel A T A har d disk drive, make sure that the har d disk drive is jumper ed as a master and the optical drive is jumpered as a slave. 1. P ower -off the comput er . 2. Remove or disconnect the following components (if installed) one at a time.
76 ThinkStation Hardware Maint enance Manual.
Chapter 10. Replacing FRUs (T ype 4105, 4157, 4217) Important Before you r eplace any FRU , read Chapt er 2 “Safety information” on page 3. These precautions and guidelines will help you work safely . FRU r eplacements are t o be done by trained service technicians only .
1 P ower cord connector 9 Microphone connect or 2 Serial port 10 Audio line-out r ear speakers connect or 3 Ethernet connector 11 SPDIF (Sony Philips Digital Inter connect F ormat) out connector 4 Ser.
5. Disengage the cover latch 1 and remove the cover . Place the cover on a at surface. Locations The following illustration will help you locat e the major FRUs in the computer .
1 Micropr ocessor , heat sink, and heat sink fan assembly 5 Hard disk drives 2 Optical drive 6 Rear fan assembly 3 3.5-inch diskett e drive or car d reader 7 P ower supply 4 Internal speaker 80 ThinkS.
Locating parts on the system board 1 Micropr ocessor 12 V power connector 16 F ront panel connector 2 Micropr ocessor fan connector 17 Cover pr esence switch connector 3 Micropr ocessor 18 Thermal sen.
Removing the fr ont bez el T o remove the front bezel: 1. Remove the cover . See “Removing the cover” on page 78. 2. Remove the front bezel by releasing the three plastic tabs 1 on the left side and pivoting the bezel outward. 3. Lay the front bez el on a at surface.
Hazardous voltage, current, and energy levels ar e present inside any component that has this label attached. There ar e no servicable parts inside these components.
7. Ensur e that the new power supply is the correct replacement. Some power supplies automatically sense the voltage, some power supplies ar e voltage specic, and some power supplies have a voltage-selection switch. If there is a voltage-selection switch, use a ballpoint pen t o slide the switch, if necessary .
CA UTION: The memory module might be very hot. T urn off the computer and wait three t o ve minutes to let the computer cool befor e opening the computer cover .
5. Go to “Completing the FRU r eplacement” on page 108. Replacing a PCI adapter card Attention Do not open your computer or attempt any r epair before r eading and understanding the “Important safety information” in the ThinkStation Safety and W arranty Guide that came with your computer .
6. Release the adapter card support retaining latch 1 if necessary . Gr asp the failing adapt er card and pull the adapter card out of the slot. Note: The adapt er card ts tightly into the card slot. If necessary, alt ernate moving each side of the adapter card a small amount until it is r emoved fr om the adapt er card slot.
7. Remove the new adapt er card from its static-prot ective package. 8. Install the new adapter car d int o the appropriat e adapt er car d slot on the system board.
Chapter 10 . Replacing FRUs (T ype 4105, 4157, 4217) 89.
9. Connect any adapter car d cables to the system boar d. 10. Latch the adapter card retainer . 11. Go to “Completing the FRU r eplacement” on page 108.
3. Remove the heat sink and fan assembly cable fr om the syst em board. Note the cable location. See “Locating parts on the system boar d ” on page 81. 4. F ollow this sequence to r emove the heat sink fr om the system board: a. Partially remove scr ew 1 , then fully r emove screw 2 , and fully r emove scr ew 1 .
10. Reconnect the heat sink fan cable. See “L ocating parts on the syst em boar d ” on page 81. 11. Go to “Completing the FRU r eplacement” on page 108. Replacing the microprocessor CA UTION: The heat sink and microprocessor might be very hot.
Notes: a. Note the orientation of the notches 1 on the micr oprocessor . This is important when r einstalling the micropr ocessor on the new system board. b. Do not drop anything onto the micropr ocessor socket while it is exposed. The socket pins must be kept as clean as possible.
9. Place the heat sink into position and r eplace the 4 scr ews t o secur e the heat sink to the syst em boar d. 10. Reconnect the heat sink fan cable. 11. Go to “Completing the FRU r eplacement” on page 108. Replacing the syst em boar d CA UTION: The heat sink and microprocessor might be very hot.
9. C arefully lift the system boar d out of the chassis. 10. Remove the micr oprocessor sock et cover fr om the new syst em board. 11. Remove the micropr ocessor from the failing system board and install it on the new syst em board. See “Replacing the micropr ocessor ” on page 92.
Note: Y our micr oprocessor socket and cover might look slightly differ ent fr om the illustr ation. d. C arefully pr ess the socket cover str aight downwar ds until it is secur ed int o the socket. e. Lower the micropr ocessor retainer and then lower the lever to secure the r etainer .
Replacing a har d disk drive Attention Do not open your computer or attempt any r epair before r eading and understanding the “Important safety information” in the ThinkStation Safety and W arranty Guide that came with your computer . T o obtain a copy of the ThinkStation Safety and Warranty Guide , go to: http://www.
5. Remove the failing hard disk drive from the br acket by exing the br acket. 6. T o install the new har d disk drive into the bracket, e x the br acket, and then align pin 1 , pin 2 , pin 3 , and pin 4 on the brack et with the holes in the har d disk drive.
Figure 3. Connecting a 3.5-inch SA T A hard disk drive Figure 4. Connecting a 2.5-inch SA T A hard disk drive Figure 5. Connecting a 3.5-inch SAS hard disk drive 9.
Replacing the hard disk drive fan assembly Attention Do not open your computer or attempt any r epair before r eading and understanding the “Important safety information” in the ThinkStation Safety and W arranty Guide that came with your computer .
7. Go to “Completing the FRU r eplacement” on page 108. Replacing an optical drive Attention Do not open your computer or attempt any r epair before r eading and understanding the “Important safety information” in the ThinkStation Safety and W arranty Guide that came with your computer .
6. Remove the r etainer br acket fr om the drive being r eplaced and install it on the new drive. 7. Slide the new optical drive int o the bay fr om the front until it snaps int o position. 8. Reconnect the signal and power cables t o the new drive. 9.
5. P ress the drive latch 1 and slide the drive out the fr ont of the computer . 6. Slide the new diskette drive or car d r eader int o the drive bay until it snaps int o position.
7. Connect the signal cable and power cable to the new diskette drive. If you are installing a card r eader , connect the car d r eader cable to the card reader connect or on the syst em boar d. See “L ocating parts on the system board ” on page 81.
8. Depending on which fan assembly you ar e r eplacing, reconnect the fan assembly cable t o the adapter card fan assembly connect or or the r ear fan assembly connect or on the syst em boar d. See “L ocating parts on the system board ” on page 81.
6. Install the new fr ont panel connectors assembly into the chassis and secure it with the screw . 7. Reconnect the cables to the system boar d. 8. Go to “Completing the FRU r eplacement” on page 108.
4. Remove the old battery . 5. Install the new batt ery . 6. Replace the comput er cover and connect the cables. See “Completing the FRU replacement” on page 108. Note: When the computer is turned on for the rst time after batt ery replacement, an err or message might be displayed.
6. Remove the speaker and speaker cable from the computer . 7. Rout e the new speaker cable and then position the new int ernal speaker tabs 3 int o the metal speaker slots and then push the internal speaker downwar d until the speaker locking tabs snap int o position.
Chapter 11. Replacing FRUs (T ype 4155, 4158, 4218) Important Before you r eplace any FRU , read Chapt er 2 “Safety information” on page 3. These precautions and guidelines will help you work safely . FRU r eplacements are t o be done by trained service technicians only .
1 P ower cord connector 9 Audio line-out front speakers connect or 2 IEEE 1394 connector 10 Microphone connector 3 Serial port 11 Audio line-out r ear speakers connect or 4 Ethernet connect ors (2) 12.
3. Disconnect the cables attached to the computer . This includes power cor ds, input/output (I/O) cables, and any other cables that ar e connected t o the comput er . See “Locating controls and connect ors on the front of your computer” on page 77 and “Rear connectors” on page 109.
1 Micropr ocessors and heat sinks (2) 6 Hard disk drive bays (5) 2 Optical drive bays (3) 7 Hard disk drive fan assembly 3 Internal speaker 8 Adapter card r etainer 4 3.
Locating parts on the system board 1 CPU 1 memory slots (6) 19 Hard disk drive connectors (5) 2 Micropr ocessor and heat sink 1 20 Optical drive connectors (3) 3 CPU 1 fan connector 21 Battery 4 CPU 1.
Removing the fr ont bez el T o remove the front bezel: 1. Remove the cover . See “Removing the cover” on page 78. 2. Remove the front bezel by releasing the three plastic tabs 1 on the left side and pivoting the bezel outward. 3. Lay the front bez el on a at surface.
Attention Do not open your computer or attempt any r epair before r eading and understanding the “Important safety information” in the ThinkStation Safety and W arranty Guide that came with your computer . T o obtain a copy of the ThinkStation Safety and Warranty Guide , go to: http://www.
Note: Use only the screws pr ovided by Lenovo. 9. Install and tighten the four screws at the r ear of the chassis t o secur e the power supply . 10. Install and tighten the two screws that secur e the power supply to the inside of the chassis. 11. Reconnect all power supply cables t o the drives, adapter car ds, and the system board.
5. Open the retaining clips as shown. If you are replacing an old memory module, open the r etaining clips and remove the memory module being replaced as shown. 6. P osition the new memory module over the memory slot. Make sur e the notch 1 on the memory module aligns corr ectly with the slot key 2 on the system board.
7. T o install the memory fan, engage the r ear of the duct with the retainer on the system board and then pivot the duct downwar ds until the duct snaps into position. Reconnect the memory fan cable to the syst em board. 8. Go to “Completing the FRU r eplacement” on page 108.
3. T ake not e of the location of all cable connections on the adapter card. It will be necessary to r econnect them properly when installing a new card. 4. Disconnect all cables connected t o the adapt er card. See “L ocating parts on the system board ” on page 113.
120 ThinkStation Hardwar e Maintenance Manual.
7. Reverse this pr ocedure to install the card. 8. Go to “Completing the FRU r eplacement” on page 108. Replacing the heat sink CA UTION: The heat sink and microprocessor might be very hot. T urn off the computer and wait three to ve minutes to let the computer cool befor e opening the computer cover .
Notes: a. Do not remove the plastic cover until you ar e r eady to install the heat sink and fan assembly on the micropr ocessor . Do not t ouch the gr ease on the heat sink and fan assembly . Do not put the heat sink and fan assembly anywher e ex cept on the micr oprocessor aft er the plastic cover has been removed and the grease exposed.
Important T ouch only the sides of the micr oprocessor . Do not touch the gold contacts on the bottom. 5. Lift the micropr ocessor straight up and out of the socket. Notes: a. Note the orientation of the notches 1 on the micr oprocessor . This is important when r einstalling the micropr ocessor on the new system board.
8. Close the micr oprocessor r etainer and clamp it with the small handle. 9. Place the heat sink into position and r eplace the 4 scr ews t o secur e the heat sink to the syst em boar d. 10. Reconnect the heat sink fan cable. 11. Go to “Completing the FRU r eplacement” on page 108.
9. C arefully lift the system boar d out of the chassis. 10. Remove the micr oprocessor sock et cover fr om the new syst em board. 11. Remove the micropr ocessor from the failing system board and install it on the new syst em board. See “Replacing the micropr ocessor ” on page 92.
Note: Y our micr oprocessor socket and cover might look slightly differ ent fr om the illustr ation. d. C arefully pr ess the socket cover str aight downwar ds until it is secur ed int o the socket. e. Lower the micropr ocessor retainer and then lower the lever to secure the r etainer .
Replacing a har d disk drive Attention Do not open your computer or attempt any r epair before r eading and understanding the “Important safety information” in the ThinkStation Safety and W arranty Guide that came with your computer . T o obtain a copy of the ThinkStation Safety and Warranty Guide , go to: http://www.
6. T o install the new har d disk drive into the bracket, e x the br acket, and then align pin 1 , pin 2 , pin 3 , and pin 4 on the brack et with the holes in the har d disk drive. Do not t ouch the cir cuit board 5 on the bottom of the har d disk drive.
Figure 8. Connecting a 3.5-inch SA T A hard disk drive Figure 9. Connecting a 2.5-inch SA T A hard disk drive Figure 10. Connecting a 3.5-inch SAS har d disk drive 9.
Replacing the hard disk drive fan assembly Attention Do not open your computer or attempt any r epair before r eading and understanding the “Important safety information” in the ThinkStation Safety and W arranty Guide that came with your computer .
7. Install the new har d disk drive fan assembly by aligning the rubber mounts of the fan assembly with the holes in the hard disk drive fan assembly br acket and pushing the rubber mounts thr ough the holes.
6. Remove the r etainer br acket fr om the drive being r eplaced and install it on the new drive. 7. Slide the new optical drive int o the bay fr om the front until it snaps int o position. 8. Reconnect the signal and power cables t o the new drive. 9.
7. Install the r etainer brack et on the new diskette drive or car d reader . 8. Disconnect the signal cable fr om the failing diskett e drive or car d reader and connect it t o the new drive. 9. Slide the new diskette drive or car d r eader int o the drive bay until it snaps int o position.
3. Disconnect the fan assembly cable fr om the system board. See “Locating parts on the system board ” on page 113. 4. The fan assembly is attached t o the chassis by four rubber mounts. Car efully remove the four rubber mounts by breaking them or cutting them with scissors and then remove the fan assembly out of the chassis.
6. Remove the two screws that secure the front panel connectors assembly t o the chassis and then r elease the front panel connect ors assembly from the chassis. 7. Align the scr ew holes in the new front panel connectors assembly with the holes in the chassis.
6. Rout e the cable for the new power switch/LED assembly thr ough the hole in the chassis and t o the system board. 7. Install the new power switch/LED assembly int o the bezel. Make sur e that the LEDs ar e in the corr ect position. 8. Connect the power switch/LED cable t o the system boar d.
Note: When the comput er is turned on for the rst time aft er replacing the batt ery, an err or message might be displayed. This is normal after r eplacing the battery . 8. T urn on the computer and all attached devices. 9. Use the Setup Utility progr am to set the dat e and time and any passwords.
7. Connect the int ernal speaker cable and the power LED cable t o the syst em boar d. See “L ocating parts on the system board ” on page 113. 8. Reinstall the hard disk drive fan br acket if removed. 9. Reinstall the front bezel. 10. Go to “Completing the FRU r eplacement” on page 108.
Chapter 12. FRU lists Attention: Read “Important information about r eplacing RoHS compliant FRUs” on page 1 befor e r eplacing any FRUs. Note: In the following tables, a CRU (Customer Replaceable Unit) is identied as either "1", "2", or "N" in the CRU column.
Item # FRUs FRU # CRU 1 Heat sink, Bloomeld performance • MT 4105: all models • MT 4157: all models • MT 4217: all models 41R5578 2 1 Heat sink, Bloomeld workstation • MT 4105: all models • MT 4157: all models • MT 4217: all models 41R5580 2 2 Micropr ocessor , Intel Xeon W3520 - 2.
Item # FRUs FRU # CRU 2 Micropr ocessor , Intel Xeon E5502 - 1.86GHz, Dual Core 4.8 QPI, 4MB L2, DDR3-800, 80W • MT 4105: C TO • MT 4157: C TO • MT 4217: C TO 46R6630 N 2 Micropr ocessor , Intel Xeon E5503 - Dual Cor e - 2.
Item # FRUs FRU # CRU 2 Micropr ocessor , Int el Xeon E5630 - Quad Cor e - 2.53GHz - 5.86 QPI DDR3-1066-12MB T urbo SMT 80W • MT 4105: C TO • MT 4157: C TO • MT 4217: C TO 71Y9047 N 2 Micropr ocessor , Int el Xeon E5640 - Quad Cor e - 2.66GHz - 5.
Item # FRUs FRU # CRU 2 Micropr ocessor , Intel Xeon X5680 - 6 Cores - 3.33GHz - 6.4 QPI DDR3-1333-12MB T urbo SMT 130W • MT 4105: C TO • MT 4157: C TO • MT 4217: C TO 71Y9033 N 2 Micropr ocessor , Intel Xeon X5677 - Quad Cor e - 3.
Item # FRUs FRU # CRU 2 Micropr ocessor , Intel Xeon W3565 - Quad Cor e - 3.2GHz - 4.8 QPI, 8MB Cache, DDR3-1066, 130W • MT 4105: C TO D2G N7M L4H P1G P2G 2AG 2BG 2CG 2DG 2KJ 2LJ 3CG 4CG 5CU 5CF 6CU 6CF 8CG 9CG 4A G • MT 4157: CT O 4BJ 5BJ • MT 4217: C TO 71Y8842 N 2 Micropr ocessor , Intel Xeon E5603 - Quad Cor e - 1.
Item # FRUs FRU # CRU 2 Micropr ocessor , Intel Xeon X5675 - 6 Cor e - 3.06Ghz - 6.4 QPI, 12MB Cache, DDR3 - 1333, T urbo, HT , 95W • MT 4105: C T O 2RH • MT 4157: C TO • MT 4217: C TO 03T8025 N 2 Micropr ocessor , Intel Xeon X5687 - Quad Core - 3.
Item # FRUs FRU # CRU 3 System board, Menor ca - 1P Int el L GA 1366 , T ylersbur g 36S, ICH10R (v1.35 , TPM enabled) • MT 4105: C TO 96G D2G M2G N5M N7M L4H E6G E9G F1G F4G F5G F8A F8Q F8T F8H F8V .
Item # FRUs FRU # CRU 3 System board, Menorca - 1P Intel X58 L GA 1366 , T ylersburg 36S, ICH10R • MT 4105: 3CG 4CG 5CU 5CF 6CU 6CF 7CM 8CG 9CG 4AG 4BH • MT 4157: C TO C3B C3H C3V B4G B5A B5Q B5T .
Item # FRUs FRU # CRU 4 Memory module, 2GB DDR3 ECC UDIMM PC3-10600 (1333MHz) • MT 4105: CT O D2G M2G N5M N7M L4H E9G F1G F4G F5G J6G J7G P8M P9M P1G P2G O4G O5G O6G O7G R9U R9F O1U O1F O3U O3F 1CG .
Item # FRUs FRU # CRU 5 Optical drive, DVD burner/CD-RW Rambo 8 (SA T A) - DOS/Linux • MT 4105: C TO 96G D2G M2G N5M N7M L4H E6G E9G F1G F4G F5G F8A F8Q F8T F8H F8V F8K F8R J6G J7G K7G K7C P8M P9M P.
Item # FRUs FRU # CRU 8 Hard disk drive, 250GB SA T A - 7200 rpm, 8MB cache, 3.5" • MT 4105: C T O M2G • MT 4157: C TO • MT 4217: C TO 46R6029 1 8 Hard disk drive, 500GB SA T A - 7200 rpm, 3 Gb/s, 16MB cache, 3.
Item # FRUs FRU # CRU 8 Hard disk drive, 300GB SAS - 15000 rpm, 3 Gb/s, 32MB cache, 3.5" • MT 4105: C TO 1CG 2DG • MT 4157: C T O M6G M8M N4U N4F N5U N5F N6U N6F 2BJ 5BJ 6BJ • MT 4217: C TO 43C6969 1 8 Hard disk drive, 300GB SAS - 15000 rpm, 3 Gb/s, 32MB cache, 3.
Item # FRUs FRU # CRU 8 Hard disk drive, 160GB SA T A solid stat e drive (SSD) - ML C, 1.8" • MT 4105: C TO P8M P9M • MT 4157: C T O 2AG • MT 4217: C TO 45N7963 1 8 Hard disk drive, 160GB SA T A solid stat e drive (SSD) - ML C, 1.
Item # FRUs FRU # CRU 8 Hard disk drive, 600GB SAS - 15000 rpm, 3.5" • MT 4105: C TO • MT 4157: C TO • MT 4217: C TO 03X3623 1 8 Hard disk drive, 250GB SA T A - 7200 rpm, 3.5" • MT 4105: C TO • MT 4157: C TO • MT 4217: C TO 03T7039 1 8 Hard disk drive, 500GB SA T A - 7200 rpm, 3.
FRUs FRU # CRU FRU, PS2 keyboar d/mouse card and cable assembly • MT 4105: all models • MT 4157: all models • MT 4217: all models 41R5604 2 FRU, adapter br acket, 2.
FRUs FRU # CRU FRU, Martell access cover assembly with tape • MT 4105: all models • MT 4157: all models • MT 4217: all models 41R5670 2 FRU, speaker cable assembly • MT 4105: all models • MT.
FRUs FRU # CRU FRU, handle ller with screws • MT 4105: all models • MT 4157: all models • MT 4217: all models 41R5699 2 FRU, r etainer , 3.5" device • MT 4105: all models • MT 4157: .
Keyboard - USB Pr eferred Pro Full size FRU # CRU Belgian/F rench • MT 4105: CT O 96G D2G M2G E6G E9G F1G F4G F5G J6G J7G K7G P1G P2G O4G O5G O6G O7G 1CG 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4A G • MT .
Keyboard - USB Pr eferred Pro Full size FRU # CRU F rench • MT 4105: CT O 96G D2G M2G E6G E9G F1G F4G F5G J6G J7G J8G K7G P1G P2G O4G O5G O6G O7G 1CG 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4AG • MT 4157:.
Keyboard - USB Pr eferred Pro Full size FRU # CRU Iceland • MT 4105: CT O 96G D2G M2G E6G E9G F1G F4G F5G J6G J7G K7G P1G P2G O4G O5G O6G O7G 1CG 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4A G • MT 4157: C .
Keyboard - USB Pr eferred Pro Full size FRU # CRU Romanian • MT 4105: CT O 96G D2G M2G E6G E9G F1G F4G F5G J6G J7G K7G P1G P2G O4G O5G O6G O7G 1CG 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4A G • MT 4157: C.
Keyboard - USB Pr eferred Pro Full size FRU # CRU Swiss F r ench/German • MT 4105: CT O 96G D2G M2G E6G E9G F1G F4G F5G J6G J7G K7G P1G P2G O4G O5G O6G O7G 1CG 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4A G .
Keyboard - F ull Size PS/2 FRU # CRU US English • MT 4105: • MT 4157: • MT 4217: 41A5039 1 Arabic • MT 4105: • MT 4157: • MT 4217: 41A5040 1 Arabic/F r ench • MT 4105: • MT 4157: • M.
Keyboard - F ull Size PS/2 FRU # CRU Dutch • MT 4105: • MT 4157: • MT 4217: 41A5049 1 F rench • MT 4105: • MT 4157: • MT 4217: 41A5050 1 F rench Canadian • MT 4105: • MT 4157: • MT 4.
Keyboard - F ull Size PS/2 FRU # CRU Italy • MT 4105: • MT 4157: • MT 4217: 41A5058 1 Japanese • MT 4105: • MT 4157: • MT 4217: 41A5059 1 Kor ean • MT 4105: • MT 4157: • MT 4217: 41A.
Keyboard - F ull Size PS/2 FRU # CRU Slovak • MT 4105: • MT 4157: • MT 4217: 41A5068 1 Spanish • MT 4105: • MT 4157: • MT 4217: 41A5069 1 Swedish/Finnish • MT 4105: • MT 4157: • MT 4.
Keyboard - Enhanced Performance FRU # CRU US English • MT 4105: • MT 4157: • MT 4217: 41A4961 1 Arabic • MT 4105: • MT 4157: • MT 4217: 41A4962 1 Arabic/F r ench • MT 4105: • MT 4157: .
Keyboard - Enhanced Performance FRU # CRU Dutch • MT 4105: • MT 4157: • MT 4217: 41A4971 1 F rench • MT 4105: • MT 4157: • MT 4217: 41A4972 1 F rench Canadian • MT 4105: • MT 4157: •.
Keyboard - Enhanced Performance FRU # CRU Italy • MT 4105: • MT 4157: • MT 4217: 41A4980 1 Japanese • MT 4105: • MT 4157: • MT 4217: 41A4981 1 Kor ean • MT 4105: • MT 4157: • MT 4217.
Keyboard - Enhanced Performance FRU # CRU Slovak • MT 4105: • MT 4157: • MT 4217: 41A4990 1 Spanish • MT 4105: • MT 4157: • MT 4217: 41A4991 1 Swedish/Finnish • MT 4105: • MT 4157: •.
Keyboard - USB Pr eferred Pro Fingerprint Keyboard FRU # CRU US English • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 41R0038 1 Arabic • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 41R.
Keyboard - USB Pr eferred Pro Fingerprint Keyboard FRU # CRU Dutch • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 41R0048 1 F rench • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 41R0049.
Keyboard - USB Pr eferred Pro Fingerprint Keyboard FRU # CRU Italy • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 41R0058 1 Japanese • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 41R005.
Keyboard - USB Pr eferred Pro Fingerprint Keyboard FRU # CRU Serbian/Cyrillic • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 41R0068 1 Slovak • MT 4105: CT O • MT 4157: CT O • MT 4217: CT.
Keyboard - USB Pr eferred Pro Fingerprint Keyboard FRU # CRU US Eur opean • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 41R0077 1 Slovenian • MT 4105: CT O • MT 4157: CT O • MT 4217: CT .
Adapters and miscellaneous FRUs Adapters and miscellaneous FRUs FRU # CRU 3.5" 20-in-1 media car d reader (with GPIO detect) • MT 4105: C TO 96G • MT 4157: CT O • MT 4217: CT O 45R8139 1 L1.
Adapters and miscellaneous FRUs FRU # CRU 768MB NVIDIA FX1800 (DVI + DP + DP) • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 46R2788 1 1.5GB NVIDIA FX4800 (DVI + DP + DP + S T), 2x3 power connector .
Adapters and miscellaneous FRUs FRU # CRU Nvidia T esla C1060 compute card (computer adapter) • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 46R6041 1 SAS controller card - 3Gb/s, 4-port host b.
Adapters and miscellaneous FRUs FRU # CRU Nvidia Quadr o 5000, dual link DVI, DP , DP , S tereo 3D 2.5GB GDDR5 • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 89Y8628 1 Nvidia Quadr o 6000, dual.
P ower Cords FRU # CRU • MT 4217: CT O Line Cor d - China • MT 4105: C T O K7C 1FC • MT 4157: C TO 2CC • MT 4217: CT O 41R3256 1 Line Cord - Japan and Japanese English • MT 4105: C T O 2GJ 2.
P ower Cords FRU # CRU Line Cor d - A models • MT 4105: C TO F8A • MT 4157: C TO 2CA • MT 4217: CT O 41R3208 1 Line Cor d - Denmark • MT 4105: C TO 96G D2G M2G E6G E9G F1G F4G F5G J6G J7G K7G .
P ower Cords - Secondary FRU # CRU Line Cor d - US • MT 4105: C TO F8A F8T R9U R9F O1U O1F O3U O3F 1K U 1KF 2EU 2EF 2FU 2FF 3AU 3AF 5CU 5CF 6CU 6CF • MT 4157: C T O B5A B5T L9U L9F N1U N1F N2U N2F.
P ower Cords - Secondary FRU # CRU Line Cor d - Italy • MT 4105: C TO 96G D2G M2G E6G E9G F1G F4G F5G J6G J7G K7G P1G P2G O4G O5G O6G O7G 1CG 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4A G • MT 4157: C TO F.
limitation, if a model came with Windows XP P rofessional pr einstalled from the factory, but has either a Windows 7 or Windows Vista CO A afxed t o the system, that model is eligible only for recovery DVDs that match the operating syst em specied on the COA.
Vista Bussiness 32 FRU # CRU Brazilian • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y3676 1 Italian • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y3677 1 Japanese • MT 4105: CT .
Vista Bussiness 32 FRU # CRU Russian • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y3680 1 T urkish • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y3681 1 Hungarian • MT 4105: CT .
Vista Bussiness 32 FRU # CRU P ortuguese • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y3694 1 Serbian-Latin • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y3695 1 Slovakian • MT .
COA afxed to the syst em, that model is eligible only for recovery DVDs that match the oper ating system specied on the COA. Windows Vista Business 64 Recovery CD FRU # CRU English • MT 4105: .
Windows Vista Business 64 Recovery CD FRU # CRU Swedish • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y3797 1 Danish • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y3794 1 Dutch •.
Windows Vista Business 64 Recovery CD FRU # CRU Simplied Chinese • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y5666 1 T r aditional Chinese • MT 4105: CT O • MT 4157: CT O • MT 421.
Windows Vista Business 64 Recovery CD FRU # CRU C&L 2 Switz erland (EN FR GR IT) • MT 4105: CT O • MT 4157: CT O • MT 4217: CT O 64Y3799 1 C&L Bel Lux (EN FR GR NL) • MT 4105: CT O •.
Windows 7 Professional 64 SP1 Recovery CD FRU # CRU P olish • MT 4105: CT O 96G D2G M2G J6G J7G K7G P1G P2G O4G O5G O6G O7G 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4A G • MT 4157: C TO B4G F3G F4G F6G G6G.
Windows 7 Professional 64 SP1 Recovery CD FRU # CRU Arabic Localiz ed • MT 4105: CT O 96G D2G M2G J6G J7G K7G P1G P2G O4G O5G O6G O7G 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4A G • MT 4157: C TO B4G F3G F.
Windows 7 Professional 64 SP1 Recovery CD FRU # CRU C&L Bel Lux (EN FR GR NL) • MT 4105: CT O 96G D2G M2G J6G J7G K7G P1G P2G O4G O5G O6G O7G 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4A G • MT 4157: C .
Windows 7 Professional 64 SP1 Recovery CD FRU # CRU Serbian-Latin • MT 4105: CT O 96G D2G M2G J6G J7G K7G P1G P2G O4G O5G O6G O7G 2AG 2BG 2CG 2DG 3CG 4CG 8CG 9CG 4A G • MT 4157: C TO B4G F3G F4G F.
Item# FRUs FRU # CRU 1 P ower supply, 1060 Watt power supply • MT 4155: CT O D1G D4G E7M E1U E1F D7C A4H A4V 93G 88G 89G 99A 99Q 99T 99K 99R A2A A2Q A2T F3J F9C E9U E9F F1U F1F G2M G3G G4G G5G G7U G.
Item# FRUs FRU # CRU 2 Heat sink - performance micropr ocessors (80W/95W) • MT 4155: all models • MT 4158: all models • MT 4218: all models 41R5578 2 2 Heat sink - workstation micr oprocessors (.
Item# FRUs FRU # CRU 3 Memory module, 4GB DDR3 2RX4 RDIMM PC3-8500 (1066MHz) • MT 4155: C TO • MT 4158: C TO • MT 4218: 46R6024 1 3 Memory module, 8GB DDR3 4RX4 RDIMM PC3-8500 (1066MHz) • MT 4.
Item# FRUs FRU # CRU 3 Memory module, 8GB DDR3 ECC UDIMM (9-9-9) PC3-10600 (1333MHz) • MT 4155: C TO • MT 4158: C TO • MT 4218: C TO 03T8429 1 4 Optical drive, DVD-ROM drive - 16x/48x (SA T A) -.
Item# FRUs FRU # CRU 6 Diskette drive, 3.5" 1.44MB 2-Mode FDD • MT 4155: C TO • MT 4158: C TO • MT 4218: 40Y9105 1 6 Diskette drive, 3.5" 1.
Item# FRUs FRU # CRU 8 Hard disk drive, 300GB SA T A - 10000 rpm, 3 Gb/s, 16MB cache, 2.5" • MT 4155: C TO • MT 4158: C TO J1G J3U J3F J4U J4F • MT 4218: C TO 46R6401 2 8 Hard disk drive, 147GB SAS - 15000 rpm, 3 Gb/s, 32MB cache, 3.
Item# FRUs FRU # CRU 8 Hard disk drive, 256GB SA T A Solid State Drive (SSD) - ML C, 1.8" • MT 4155: C TO • MT 4158: C TO • MT 4218: C TO 45N7959 1 8 Hard disk drive, 256GB SA T A Solid State Drive (SSD) - ML C, 1.
Item# FRUs FRU # CRU 8 Hard disk drive, 600GB SA T A - 10000 rpm, 16MB cache, 2.5" • MT 4155: C TO • MT 4158: C TO • MT 4218: C TO 91Y1658 1 8 Hard disk drive, 600GB SAS - 15000 rpm, 3.5" • MT 4155: C TO • MT 4158: C TO • MT 4218: C TO 03X3616 1 8 Hard disk drive, 600GB SAS - 15000 rpm, 3.
Item# FRUs FRU # CRU 10 Micropr ocessor , Int el Xeon E5504 - 2.00GHz, Quad Core- 4.8QPI, 4MB L2, DDR3-800, 80W • MT 4155: C TO • MT 4158: C TO • MT 4218: 46R6631 N 10 Micropr ocessor , Int el Xeon E5506 - 2.
Item# FRUs FRU # CRU 10 Micropr ocessor , Intel Xeon E5640 - Quad Core - 2.66GHz - 5.86 QPI DDR3-1066-12MB T urbo SMT 80W • MT 4155: • MT 4158: C TO • MT 4218: 71Y9045 N 10 Micropr ocessor , Intel Xeon X5550 - 2.
Item# FRUs FRU # CRU 10 Micropr ocessor , Intel Xeon X5677 - Quad Cor e - 3.46GHz - 6.4 QPI DDR3-1333-12MB T urbo SMT 130W • MT 4155: C TO • MT 4158: C TO • MT 4218: 71Y9035 N 10 Micropr ocessor , Intel Xeon X5670 - 6 Cor e - 2.
Item# FRUs FRU # CRU 10 Micropr ocessor , Intel Xeon E5649 - 6 Cor e - 2.53Ghz - 5.86 QPI, 12MB Cache, DDR3 - 1333, T urbo, HT , 80W • MT 4155: C T O G9M • MT 4158: CT O H9G K4M K5M L6G N7M O1G • MT 4218: C TO 03T8027 N 10 Micropr ocessor , Intel Xeon X5647 - Quad Cor e - 2.
Item# FRUs FRU # CRU 11 System board, Ibiza - 2P Intel L GA 1366, T ylersbur g 36D , ICH10 (GA level v1.7, TPM enabled) • MT 4155: CT O D1G D4G E7M E1U E1F D7C A4H A4V 93G 88G 89G 91G A2A A2Q A2T F9.
Item# FRUs FRU # CRU 11 System board, Ibiza - 2P Int el L GA 1366, T ylersbur g 36D , ICH10 (Change 5V USB resist ors + Marvell 3.1.0.21 FW) • MT 4155: J1J J2J J3J J4J J5J J6J J7J J8J J9H K1G K2G K3.
Item# FRUs FRU # CRU 11 System board, Ibiza - 2P Int el L GA 1366, T ylersburg 36D , ICH10 (PCI 2.3 compliance r ework) • MT 4155: J1J J2J J3J J4J J5J J6J J7J J8J J9H K1G K2G K3G K4U K4F K6G K7G •.
Item# FRUs FRU # CRU N3K N3R N3E N3J N4U N4F N5U N5F N6M N7M N8M N9G O1G O2G O3G O4G O5G O6G • MT 4218: 12 Rear fan, 120 mm system exhaust • MT 4155: all models • MT 4158: all models • MT 4218: all models 45J9605 2 Mechanical FRUs The FRUs listed in the following tables are not illustr ated.
FRUs FRU # CRU FRU, cover assembly (access panel), Remy • MT 4155: all models • MT 4158: all models • MT 4218: all models 41R5654 1 FRU, label kit, Remy • MT 4155: all models • MT 4158: all .
FRUs FRU # CRU Enhanced cable assembly • MT 4155: all models • MT 4158: all models • MT 4218: all models 41R5604 2 Heat sink RM bracket • MT 4155: all models • MT 4158: all models • MT 4218: all models 41R5592 2 2.
Keyboard - P referred Pro F ull size FRU # CRU Belgian/F rench • MT 4155: CT O D1G D4G 93G 88G 89G G3G G4G G5G K1G K2G K3G K6G K7G • MT 4158: CT O C2G C3G C5G C7G C8G D2G H8G H9G J1G L5G L6G L7G L.
Keyboard - P referred Pro F ull size FRU # CRU F rench Canadian • MT 4155: C TO E1F E9F F1F G7F G8F H9F K4F • MT 4158: C T O D6F F9F G7F H1F J2F J3F J4F J5F J6F J7F J8F J9F K1F M3F M4F N1F N2F N3F.
Keyboard - P referred Pro F ull size FRU # CRU Italy • MT 4155: CT O D1G D4G 93G 88G 89G G3G G4G G5G K1G K2G K3G K6G K7G • MT 4158: CT O C2G C3G C5G C7G C8G D2G H8G H9G J1G L5G L6G L7G L8G L9G M1G.
Keyboard - P referred Pro F ull size FRU # CRU Russian/Cyrillic • MT 4155: CT O D1G D4G 93G 88G 89G G3G G4G G5G K1G K2G K3G K6G K7G • MT 4158: CT O C2G C3G C5G C7G C8G D2G H8G H9G J1G L5G L6G L7G .
Keyboard - P referred Pro F ull size FRU # CRU T urkish • MT 4155: CT O D1G D4G 93G 88G 89G G3G G4G G5G K1G K2G K3G K6G K7G • MT 4158: CT O C2G C3G C5G C7G C8G D2G H8G H9G J1G L5G L6G L7G L8G L9G .
Keyboard - F ull Size PS/2 FRU # CRU Brazilian • MT 4155: • MT 4158: • MT 4218: 41A5044 1 Bulgarian • MT 4155: • MT 4158: • MT 4218: 41A5045 1 Hong K ong/T aiwan • MT 4155: • MT 4158: .
Keyboard - F ull Size PS/2 FRU # CRU Greek • MT 4155: • MT 4158: • MT 4218: 41A5054 1 Greek/US • MT 4155: • MT 4158: • MT 4218: 41A5080 1 Hebrew • MT 4155: • MT 4158: • MT 4218: 41A5.
Keyboard - F ull Size PS/2 FRU # CRU P olish • MT 4155: • MT 4158: • MT 4218: 41A5063 1 P ortuguese • MT 4155: • MT 4158: • MT 4218: 41A5064 1 Romanian • MT 4155: • MT 4158: • MT 421.
Keyboard - F ull Size PS/2 FRU # CRU T urkish • MT 4155: • MT 4158: • MT 4218: 41A5073 1 T urkish • MT 4155: • MT 4158: • MT 4218: 41A5074 1 UK English • MT 4155: • MT 4158: • MT 421.
Keyboard - Enhanced P erformance FRU # CRU Belgian/UK • MT 4155: • MT 4158: • MT 4218: 41A4965 1 Brazilian • MT 4155: • MT 4158: • MT 4218: 41A4966 1 Bulgarian • MT 4155: • MT 4158: .
Keyboard - Enhanced P erformance FRU # CRU German • MT 4155: • MT 4158: • MT 4218: 41A4975 1 Greek • MT 4155: • MT 4158: • MT 4218: 41A4976 1 Greek/US • MT 4155: • MT 4158: • MT 4218.
Keyboard - Enhanced P erformance FRU # CRU Norwegian • MT 4155: • MT 4158: • MT 4218: 41A4984 1 P olish • MT 4155: • MT 4158: • MT 4218: 41A4985 1 P ortuguese • MT 4155: • MT 4158: •.
Keyboard - Enhanced P erformance FRU # CRU Thailand • MT 4155: • MT 4158: • MT 4218: 41A4994 1 T urkish • MT 4155: • MT 4158: • MT 4218: 41A4995 1 T urkish • MT 4155: • MT 4158: • MT.
Keyboard - USB P referred Pro Fingerprint FRU # CRU Belgium F r ench • MT 4155: CT O • MT 4158: CT O • MT 4218: 41R0041 1 Belgium English • MT 4155: CT O • MT 4158: CT O • MT 4218: 41R0042.
Keyboard - USB P referred Pro Fingerprint FRU # CRU F rench Canadian • MT 4155: CT O • MT 4158: CT O • MT 4218: 41R0051 1 German • MT 4155: CT O • MT 4158: CT O • MT 4218: 41R0052 1 Greek .
Keyboard - USB P referred Pro Fingerprint FRU # CRU LA Spanish • MT 4155: CT O • MT 4158: CT O • MT 4218: 41R0061 1 Norwegian • MT 4155: CT O • MT 4158: CT O • MT 4218: 41R0062 1 P olish .
Keyboard - USB P referred Pro Fingerprint FRU # CRU Swedish/Finnish • MT 4155: CT O • MT 4158: CT O • MT 4218: 41R0071 1 Swiss F r ench/German • MT 4155: CT O • MT 4158: CT O • MT 4218: 41.
Mice FRU # CRU N1U N1F N1S N1P N1L N1D N1Y N1G N1M N1A N1Q N1T N1C N1B N1H N1V N1K N1R N1E N1J N2U N2F N3U N3F N3S N3P N3L N3D N3Y N3G N3M N3A N3Q N3T N3C N3B N3H N3V N3K N3R N3E N3J N4U N4F N5U N5F N.
Adapters and miscellaneous FRUs FRU # CRU Lenovo 3 pieces speakers (China only) • MT 4155: CT O • MT 4158: CT O • MT 4218: 45C8640 1 Lenovo 2 pieces speakers (China only) • MT 4155: CT O • M.
Adapters and miscellaneous FRUs FRU # CRU 256MB NVIDIA NVS295 (dual DP) • MT 4155: CT O • MT 4158: C T O J2U J2F • MT 4218: 46R2782 1 1GB NVIDIA FX3800 (DVI + DP + ST), 2x3 power connector • M.
Adapters and miscellaneous FRUs FRU # CRU SoundBlaster Titanium audio card (PCIe) • MT 4155: CT O • MT 4158: CT O • MT 4218: 46T0407 1 Modem phone cable • MT 4155: CT O • MT 4158: CT O • M.
Adapters and miscellaneous FRUs FRU # CRU DP t o DVI dongle 200 mm • MT 4155: CT O • MT 4158: C TO D2G H1U H1F J5U J5F K1U K1F K8M M8J • MT 4218: 43N9160 1 Nvidia Quadro 600, Dual link DVI, DP ,.
P ower Cords FRU # CRU Line Cor d - Br azil (P ortuguese) • MT 4155: CT O • MT 4158: C T O N1P N3P • MT 4218: 41R3270 1 Line Cor d - LA High V olt (APU) • MT 4155: CT O • MT 4158: C T O D6Y .
P ower Cords FRU # CRU Line Cor d - Switzerland • MT 4155: CT O 93G 88G 89G G3G G4G G5G K1G K2G K3G K6G K7G • MT 4158: CT O D6G C2G C3G C5G C7G C8G D2G H8G H9G J1G L5G L6G L7G L8G L9G M1G M2G N1G .
P ower Cords - Secondary FRU # CRU Line Cor d - China • MT 4155: C T O D7C F9C • MT 4158: C TO D6C C6C N1C N3C • MT 4218: 41R3257 1 Line Cord - Japan and Japanese English • MT 4155: C TO J1J J.
P ower Cords - Secondary FRU # CRU Line Cor d - A models • MT 4155: CT O • MT 4158: C TO D6A N1A N3A • MT 4218: 41R3209 1 Line Cor d - Denmark • MT 4155: CT O 93G 88G 89G G3G G4G G5G K1G K2G K.
Windows XP P rofessional 64 Mono FRU # CRU US English • MT 4155: CT O • MT 4158: CT O • MT 4218: CT O 03W2824 1 Japanese • MT 4155: CT O • MT 4158: CT O • MT 4218: CT O 03W2825 1 Windows V.
Windows Vista Business 32 FRU # CRU Italian • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3677 1 Japanese • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y5662 1 Norwegian • MT 4155: CT O .
Windows Vista Business 32 FRU # CRU T urkish • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3681 1 Hungarian • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3682 1 Greek • MT 4155: CT O •.
Windows Vista Business 32 FRU # CRU Serbian-Latin • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3695 1 Slovakian • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3696 1 Arabic Localiz ed • .
Windows Vista Business 64 FRU # CRU English • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y5664 1 Russian English • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3771 1 F rench • MT 4155: C.
Windows Vista Business 64 FRU # CRU Danish • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3794 1 Dutch • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3790 1 Czech • MT 4155: CT O • MT 41.
Windows Vista Business 64 FRU # CRU T r aditional Chinese • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3785 1 T r aditional Chinese - Hong Kong • MT 4155: CT O • MT 4158: CT O • MT 4218: .
Windows Vista Business 64 FRU # CRU C&L Switz erland (EN FR GR IT) • MT 4155: CT O • MT 4158: CT O • MT 4218: 64Y3799 1 C&L Bel Lux (EN FR GR NL) • MT 4155: CT O • MT 4158: CT O • .
Windows 7 Professional 64 SP1 FRU # CRU T urkish • MT 4155: C T O D1G D4G 93G 88G 89G G3G G4G G5G K1G K2G K3G K6G K7G • MT 4158: CT O C2G C3G C5G C7G C8G D2G H8G H9G J1G L5G L6G L7G L8G L9G M1G M2.
Windows 7 Professional 64 SP1 FRU # CRU India English • MT 4155: CT O • MT 4158: C TO D6Q N1Q N3Q • MT 4218: 03W2889 1 Hong Kong • MT 4155: C TO A4V • MT 4158: C TO D6B N1B N3B • MT 4218: .
Windows 7 Professional 64 SP1 FRU # CRU P ortuguese • MT 4155: C T O D1G D4G 93G 88G 89G G3G G4G G5G K1G K2G K3G K6G K7G K6G K7G • MT 4158: CT O C2G C3G C5G C7G C8G D2G H8G H9G J1G L5G L6G L7G L8G.
250 ThinkStation Hardwar e Maintenance Manual.
Chapter 13. Additional Service Information This chapt er pr ovides additional information that the service repr esentative might nd helpful. Security features Security features in this section incl.
Updating (ashing) BIOS fr om a disc This section pr ovides instructions on how to update (ash) BIOS fr om a disc. System pr ogram updates are available at: http://www.lenovo.com/support on the World Wide W eb. 1. Mak e sur e the optical drive you want to use is set as the rst boot device in the startup device sequence.
9. Reconnect the power cor ds for the computer and monit or to electrical outlets. 10. Insert the POS T/BIOS update (ash) diskette int o drive A, and turn on the comput er and the monit or . 11. The recovery session will take two to thr ee minutes.
254 ThinkStation Hardwar e Maintenance Manual.
Appendix A. Notices Lenovo may not offer the products, services, or featur es discussed in this document in all countries. Consult your local L enovo repr esentative for information on the pr oducts and services curr ently available in your area.
T elevision output notice The following notice applies to models that have the fact ory-installed television-output feature. This product incorporat es copyright prot ection technology that is prot ected by method claims of certain U.S. patents and other intellectual property rights owned by Macr ovision Corpor ation and other rights owners.
Appendix B. System memory speed The Intel Xeon micr oprocessor families compatible with this ThinkStation computer featur e an integr ated memory contr oller , which pr ovides the micropr ocessor with dir ect access to the system memory .
T able 1. System memory speed (continued) Intel Xeon W3550 1066 MHz 1066 MHz 1066 MHz Intel Xeon W3565 1066 MHz 1066 MHz 1066 MHz Intel Xeon W3570 1333 MHz 1066 MHz 1066 MHz Intel Xeon W3580 1333 MHz .
Inde x A adapter card, replacing 86 adapter cards, replacing 118 administrat or, passwor d 42 advanced settings 43 B battery, r eplacing 106, 136 C card r eader, r eplacing 102, 132 changing password .
connectors 81, 113 T tempor ary startup device 43 U user , password 42 using passwords 41 Setup Utility 41 V viewing and changing settings 41 260 ThinkStation Hardwar e Maintenance Manual.
.
Part Number: 53Y4348 Printed in USA (1P) P/N: 53Y4348 *53Y4348*.
デバイスLenovo 4158の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lenovo 4158をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLenovo 4158の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lenovo 4158の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lenovo 4158で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lenovo 4158を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLenovo 4158の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lenovo 4158に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLenovo 4158デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
