LenovoメーカーT430Uの使用説明書/サービス説明書
ページ先へ移動 of 101
Har dwar e Maint enance Manual ThinkP ad T430u.
Note: Before using this information and the pr oduct it supports, be sur e to read the gener al information under Appendix A “Notices” on page 93. First Edition (August 2012) © Copyright Lenovo 2012.
Contents About this manual . . . . . . . . . . . iii Chapter 1. Safety information . . . . . . 1 General safety . . . . . . . . . . . . . . . . 1 Electrical safety . . . . . . . . . . . . . . . 2 Safety inspection guide . . . . . . . . . . . . 3 Handling devices that ar e sensitive t o electr ostatic discharge .
1050 Memory module . . . . . . . . . . . . 66 1060 PCI Express Mini C ard for wireless LAN . . 67 1070 PCI Express Mini Car d for wir eless W AN or mSA T A solid-state drive . . . . . . . . . . . 68 1080 Backup battery . . . . . . . . . . . . 71 1090 Keyboar d bez el .
About this manual This manual contains service and r eference information for the following ThinkP ad ® products. ThinkPad T430u Machine T ype (MT): 3351, 3352, 3353, 6273, and 8614 Use this manual along with the advanced diagnostic tests to troubleshoot pr oblems.
iv Hardwar e Maintenance Manual.
Chapter 1. Safety information This chapt er presents following safety information that you need to be familiar with befor e you service a ThinkP ad notebook comput er .
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and t est equipment. Some hand tools have handles cover ed with a soft material that does not insulat e you when working with live electrical curr ents.
– Use caution; do not become a victim yourself. – Switch off power . – Send another person t o get medical aid. Safety inspection guide The purpose of this inspection guide is to assist you in identifying pot entially unsafe conditions.
1. Use pr oduct-specic ESD pr ocedures when they ex ceed the r equirements noted here. 2. Ensur e that the ESD prot ective devices you use have been certied (ISO 9000) as fully effective. When handling ESD-sensitive parts: • K eep the parts in prot ective packages until they ar e inserted into the product.
DANGER DANGER DANGER DANGER DANGER DANGER Chapter 1 . Safety information 5.
DANGER 6 Hardwar e Maintenance Manual.
Chapter 1 . Safety information 7.
PERIGO PERIGO PERIGO PERIGO PERIGO PERIGO 8 Hardwar e Maintenance Manual.
PERIGO PERIGO DANGER DANGER DANGER Chapter 1 . Safety information 9.
DANGER DANGER DANGER DANGER DANGER VORSICHT 10 Hardwar e Maintenance Manual.
VORSICHT VORSICHT VORSICHT VORSICHT Chapter 1 . Safety information 11.
VORSICHT VORSICHT VORSICHT 12 Hardwar e Maintenance Manual.
Chapter 1 . Safety information 13.
14 Hardwar e Maintenance Manual.
Chapter 1 . Safety information 15.
16 Hardwar e Maintenance Manual.
Chapter 1 . Safety information 17.
18 Hardwar e Maintenance Manual.
Chapter 1 . Safety information 19.
20 Hardwar e Maintenance Manual.
Chapter 2. Important service information This chapter pr esents following important service information that applies to all machine types supported by this manual: • “Str ategy for r eplacing FRUs.
• If an adapt er or a device consists of mor e than one FRU , any of the FRUs might be the cause of the error . Before replacing the adapter or device, r emove the FRUs, one by one, t o see if the sympt oms change. Replace only the FRU that changed the sympt oms.
Custom Model V ariant (CMV) This is a unique congur ation that has been negotiated between Lenovo and the customer . A unique 4-digit MT and 3-digit model is pr ovided to the customer t o place orders (Example: 1829-W15). A CMV is a special bid offering.
• T o view the complete list of FRUs, do the following: 1. Click Pr oduct & P arts Detail and then follow the instructions on the screen to reach the P roduct and P arts Details page. 2. Click the P arts Detail tab to view the list of service parts.
Chapter 3. General checkout This chapter pr esents the following information: • “What to do rst” on page 25 • “Checkout guide” on page 26 – “Lenovo Solution Cent er ” on page 26 .
• L CD panel cracked fr om the application of e xcessive force or from being dropped • Scr atched (cosmetic) parts • Dist ortion, deformation, or discolor ation of the cosmetic parts • Plastic.
T o download and install a quick test pr ogram, go t o http://www.lenovo.com/diagnose, and follow the instructions on the W eb sit e. T o run a quick test using the downloaded pr ogram, do the following: 1. Go t o the C:SWT OOLSldiag folder . 2. Double-click the gui_lsc_lit e.
T o use the diagnostic medium you have creat ed, do one of the following: • If you have creat ed the bootable diagnostic medium on a USB device, do the following: 1. A ttach the USB device t o the computer . 2. T urn on the computer . If the computer cannot be turned on, go t o “P ower system checkout” on page 28, and check the power sources.
Pin V oltage (V dc) 1 +20 2 0 3 Ground 1 2 3 (20V) Note: Output voltage across pin 2 of the ac power adapt er might be different from the one you are servicing. 3. If the voltage is not corr ect, replace the ac power adapter . 4. If the voltage is acceptable, replace the system boar d.
30 Hardwar e Maintenance Manual.
Chapter 4. Related service information This chapter pr esents the following information: • “Restoring the fact ory contents by using Recovery Disc Set” on page 31 • “P asswords” on page 32.
c. Select the CD/DVD drive as the 1st Boot Device . 2. Insert the Operating System Recovery Disc int o the DVD drive. 3. P ress F10 to save the ThinkP ad Setup congur ation changes. F ollow the instructions on the screen to begin the r ecovery pr ocess.
Attention: If the user HDP has been for gotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither L enovo nor.
4. When the user HDP icon is displayed, press F1 t o switch t o mast er HDP mode. When the master HDP icon is displayed, type in the master HDP to enter ThinkPad Setup. 5. Select Security , using the cursor directional keys t o move down the menu. 6. Select P assword .
Hibernation mode In hibernation mode, the following occurs: • The system status, RAM, VRAM, and setup data are stor ed on the har d disk. • The system is powered off. If you have dened one of the following actions as the event that causes the system t o go into hibernation mode, perform that action.
Numeric error codes T able 1. Numeric error codes Symptom or err or (beeps, if any) FRU or action, in sequence 0177 Bad SVP data, st op POST task. System board. 0183 Bad CRC of Security Settings in EFI V ariable. Ent er ThinkP ad Setup. 1. Run ThinkP ad Setup.
Error messages T able 2. Error messages Symptom or err or (beeps, if any) FRU or action, in sequence F an err or . 1. F an . 2. Thermal grease. 3. System boar d. Thermal sensing error . The thermal sensor is not functioning corr ectly . Have the computer serviced.
If the L CD you are servicing has two or less visible defective pix els, it should not be considered faulty . However , if the L CD has thr ee or mor e visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.
a. System boar d b. L CD assembly Chapter 4 . Related service information 39.
40 Hardwar e Maintenance Manual.
Chapter 5. Status indicat ors This chapter presents the system status indicators that show the status of the computer . 3 2 1 4 5 T able 6. Status indicators Indicator Meaning 1 Caps Lock status indicator When the Caps L ock mode is enabled, this indicator will be displayed on the screen.
T able 6. Status indicat ors (continued) Indicator Meaning 4 System status indicator 5 System status indicator The illuminated dot in the ThinkP ad logo on the outer lid of the comput er and on the palm rest works as a system status indicat or: it shows whether the comput er is in sleep, hibernation, or normal mode.
Chapter 6. F unction k ey combinations The following table describes the functions of Fn key combinations. T able 7. Function key combinations Key combinations Description Fn+Esc Pr ess Fn+Esc to mut e the sound of the computer . Fn+F1 Pr ess Fn+F1 to turn down the volume of the comput er .
44 Hardwar e Maintenance Manual.
Chapter 7. L ocations This chapt er intr oduces the locations of the computer hardwar e components. Locating computer controls, connectors, and indicators This topic introduces the locations of the comput er contr ols, connect ors, and indicators.
Rear view 1 2 4 5 6 7 8 3 1 System status indicat or 5 F an louvers (rear) 2 Media card reader 6 HDMI connector 3 F an louvers (right) 7 SIM car d slot 4 Security keyhole 8 Mini DisplayP ort connector.
Notes: • Each FRU is available for all types or models, unless otherwise specied. • CRU statement for customers: Y ou can resolve some problems with your pr oduct with a replacement part you can install yourself, called a “Customer Replaceable Unit” or “CRU .
Major FRUs and CRUs 1 2 3 4 5 13 6 7 8 9 10 11 12 14 15 16 17 18 19 20 22 23 21 48 Hardwar e Maintenance Manual.
No. Description Self-service CRU Optional-service CRU 1 L CD unit No No 2 Keyboar d Y es No 3 Speaker assembly No No 4 P ower button sub card No No 5 Keyboar d bez el No No 6 Fingerprint r eader (on s.
L CD FRUs and CRUs 1 4 2 3 5 6 8 7 No. Description Self-service CRU Optional-service CRU 1 L CD bez el No No 2 L CD panel No No 3 Hinges No No 4 Integr ated camera and microphone combo card No No 5 Ca.
No. Description Self-service CRU Optional-service CRU 7 Antenna kit No No 8 L CD cable No No Looking up FRU information F or detailed FRU information, including part numbers, descriptions, and substitution part numbers, go t o http://www.lenovo.com/serviceparts-lookup.
52 Hardwar e Maintenance Manual.
Chapter 8. FRU replacement notices This chapt er pr esents notices relat ed to r emoving and replacing parts. Read this chapter carefully before replacing any FRU . Notes: • Each FRU is available for all types or models, unless otherwise specied.
Notes: • Ensur e that you use the corr ect screw . It is r ecommended t o use new screws for replacements. • If you have a tor que screwdriver , tight en all scr ews rmly to the tor que specied in the screw information table for each step. • Ensur e t orque screw drivers ar e calibr ated correctly following the country specications.
Product ID on rear label: TTTT -MMM (Use this number when setting Serial Number) In the example, the Serial Number to be input is “1S TTTTMMMSSSSSSS”. Retaining the UUID The Universally Unique Identier (UUID) is a 128-bit number uniquely assigned t o your computer at production and stored in the EEPROM of your system board.
56 Hardwar e Maintenance Manual.
Chapter 9. Removing or r eplacing a FRU This chapt er provides instructions on how to r emove or replace a FRU . CRU statement for customers: Y ou can r esolve some pr oblems with your pr oduct with a r eplacement part you can install yourself, called a “Cust omer Replaceable Unit” or “CRU.
Before ser vicing the computer Car efully read this topic befor e servicing the computer . Disabling the batt er y pack in the UEFI BIOS Before r eplacing any FRU, ensur e that you have disabled the built-in batt ery by doing the following: 1. T urn off the computer .
1 2 When installing: Slide the bott om cover latch to the unlocked position. While holding the bottom cover latch in the unlock ed position, attach the bottom cover 1 , and pivot it downwards until it is rmly attached 2 . Release the bottom cover latch to secur e the bott om cover .
1 1 1 1 1 1 1 1020 Battery pack F or access, r emove this FRU: • “1010 Bottom cover” on page 58 Important notices for replacing a battery pack • The Lenovo Solution Cent er pr ogram provides an aut omatic battery diagnostic test that det ermines if the batt ery pack is defective.
1 2 Step Screw (quantity) Color T orque 2 M2 × 5.0 mm, wafer -head, nylon-coated (5) Black 0.181 Nm (1.85 kgf-cm) Remove the battery pack by using the pull tab 3 . 3 1030 Hard disk drive or solid-state drive assembly Attention: • Do not dr op the drive or apply any physical shock t o it.
F or access, remove these FRUs in or der: • “1010 Bottom cover” on page 58 • “1020 Battery pack” on page 60 Removal steps of hard disk drive or solid-state drive assembly Remove the scr ews 1 that secure the hard disk drive or solid-stat e drive assembly .
Removal steps of hard disk drive or solid-state drive brack et 1 1 1 1 Step Screw (quantity) Color T orque 1 M2 × 6.0 mm, at-head, nylon-coat ed (4) Black 0.
Step Screw (quantity) Color T orque 1 M2 × 5.0 mm, wafer -head, nylon-coated (1) Black 0.181 Nm (1.85 kgf-cm) Push the keyboard in the direction as shown by the arrows 2 until the hooks on the r ear edge of the keyboard are detached fr om the keyboar d bez el.
T urn over the keyboar d, and then detach the keyboard connectors. 7 6 8 9 5 When installing: Ensure that the keyboar d connectors ar e attached rmly . Attach the keyboar d so that the fr ont edge of the keyboard is under the k eyboard be zel as shown in the following illustr ation.
When the fr ont edge of the keyboar d is housed rmly, gently pr ess the keyboard with your palms to slide the keyboard t oward you until it snaps into position.
1060 PCI Expr ess Mini C ard for wir eless LAN F or access, remove these FRUs in or der: • “1010 Bottom cover” on page 58 • “1020 Battery pack” on page 60 • “1040 Keyboard” on page 63 Removal steps of PCI Expr ess Mini Car d for wireless LAN Detach the ant enna RF connect ors 1 .
1070 PCI Express Mini C ard for wireless W AN or mSA T A solid-stat e drive Depending on models, the computer you ar e servicing might come with one of the following cards installed: PCI Expr ess Mini C ard for wireless WAN, PCI Express Half Mini Card for wir eless WAN, or mSA T A solid-state drive.
3 Removal steps of PCI Express Half Mini C ard for wireless W AN Detach the antenna RF connectors 1 . Then remove the scr ew 2 . Step Screw (quantity) Color T orque 2 M2 × 3.
3 4 4 Removal steps of mSA T A solid-state drive Attention: • Do not dr op the drive or apply any physical shock t o it. The drive is sensitive to physical shock. Impr oper handling can cause damage and permanent loss of data. • Befor e removing the drive, have the user make a backup copy of all the information on it if possible.
Remove the screw 1 that secur es the mSA T A solid-state drive. 1 Step Screw (quantity) Color T orque 1 M2 × 3.0 mm, wafer -head, nylon-coated (1) Black 0.
1 2 When installing: Ensure that the connect or is attached rmly . 1090 K eyboard bez el F or access, remove these FRUs in or der: • “1010 Bottom cover” on page 58 • “1020 Battery pack”.
Step Screw (quantity) Color T orque 1 M2.5 × 6.5 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4.00 kgf-cm) 2 M2 x 5 mm, wafer -head, nylon-coated (1) Black 0.
Detach the connect ors as shown in the following illustration. 7 6 8 10 9 14 12 13 11 When installing: Ensure that the connectors ar e attached rmly . Release the keyboard bezel fr om the frame using a plastic pry tool as shown in the following illustr ation.
When installing: Route the cables as shown in the following illustr ation befor e you attach the keyboar d bez el. 1110 Speak er assembly F or access, remove these FRUs in or der: • “1010 Bottom c.
1120 Media car d r eader F or access, remove these FRUs in or der: • “1010 Bottom cover” on page 58 • “1020 Battery pack” on page 60 • “1030 Hard disk drive or solid-state drive assemb.
1130 Fingerprint r eader If the computer you are servicing has the ngerprint r eader , follow the following instructions to r emove or replace it. F or access, remove these FRUs in or der: • “1.
6 5 1140 P ower button sub car d F or access, remove these FRUs in or der: • “1010 Bottom cover” on page 58 • “1020 Battery pack” on page 60 • “1030 Hard disk drive or solid-state driv.
When installing: Ensure that the end of cable marked with PB is attached rmly to the power button sub card, and the end mark ed with MB is attached rmly to the syst em board.
F or access, remove these FRUs in or der: • “1010 Bottom cover” on page 58 • “1020 Battery pack” on page 60 • “1030 Hard disk drive or solid-state drive assembly” on page 61 • “1.
4 When installing: • Befor e you attach the thermal fan assembly t o the computer , apply thermal gr ease, at an amount of 0.2 grams, on the parts marked a as in the following illustr ations. Either too much or too less application of grease might cause a thermal problem due t o imperfect contact with a component.
Removal steps of syst em board Attention: The following components soldered on the system boar d ar e extr emely sensitive. When you service the syst em board, avoid any kind of rough handling.
• “1030 Hard disk drive or solid-state drive assembly” on page 61 • “1040 Keyboard” on page 63 • “1050 Memory module” on page 66 • “1060 PCI Expr ess Mini Car d for wir eless LAN.
1 2 3 4 5 6 8 7 9 13 10 11 12 1 Rating label 8 T aiwan wireless WAN label 2 COA label 9 Indonesia POS TEL label (for wir eless LAN) 3 Asset tag 10 Indonesia rating label 4 S/N label 11 Israel r ating .
Removal st eps of L CD unit 1 2 When installing: Ensure that the connectors ar e attached rmly . Detach the ant ennas as shown in the following illustr ation. 3 3 3 3 3 3 3 3 When installing: Ensur e that the cables ar e routed corr ectly as shown in the above illustr ation.
4 4 4 4 4 Step Screw (quantity) Color T orque 4 M2.5 × 6.5 mm, wafer-head, nylon-coated (5) Black 0.392 Nm (4.00 kgf-cm) 5 5 86 Hardwar e Maintenance Manual.
2020 L CD bez el Removal st eps of L CD bezel When installing: Ensure that all the latches ar e attached rmly . 2030 L CD panel F or access, r emove this FRU: • “2020 L CD bez el ” on page 87 Removal st eps of L CD panel 1 1 1 1 1 1 Chapter 9 .
Step Screw (quantity) Color T orque 1 M2 × 2.5 mm, wafer -head, nylon-coated (6) Silver 0.181 Nm (1.85 kgf-cm) 3 4 2 2040 Integrat ed camera and microphone combo card F or access, r emove this FRU: .
2050 Hinges F or access, remove these FRUs in or der: • “1010 Bottom cover” on page 58 • “1040 Keyboard” on page 63 • “1060 PCI Expr ess Mini Car d for wir eless LAN” on page 67 • .
When installing: Befor e you install the hinges, r oute the cables as shown in the following illustration. Ensur e that all cables ar e routed on the far side of the rib and no cables ar e pinched under the fr ame.
3 3 3 3 Cable routing: When you install the ant enna assembly, r oute the cables as shown in the following illustration. As you r oute the cables, ensure that they are not subject to any tension. T ension could cause the cables t o be damaged by the cable guides, or a wir e to be br oken.
92 Hardwar e Maintenance Manual.
Appendix A. Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the pr oducts and services currently available in your area.
Electronic emissions notices F or electr onic emission information on Class B digital devices, r efer to the corr esponding information in the User Guide .
Part Number: 0B48901 (1P) P/N: 0B48901 *1P0B48901*.
デバイスLenovo T430Uの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lenovo T430Uをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLenovo T430Uの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lenovo T430Uの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lenovo T430Uで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lenovo T430Uを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLenovo T430Uの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lenovo T430Uに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLenovo T430Uデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。