LG Electronicsメーカー32LC41/4R-ZAの使用説明書/サービス説明書
ページ先へ移動 of 30
R LCD TV SER VICE MANUAL CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. CHASSIS : LP78A MODEL : 32LC41/4R 32LC41/4R-ZA MODEL : 32LC42 32LC42-ZC MODEL : 32LC43 32LC43-ZA/ZE MODEL : 32LC44 32LC43-ZB website:http://biz.
- 2 - CONTENTS CONTENTS .............................................................................................. 2 SAFETY PRECAUTIONS ..........................................................................3 SPECIFICA TION ....................
- 3 - SAFETY PRECAUTIONS Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by i n t h e Schematic Diagram and Replacement Parts List.
- 4 - CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication.
- 5 - IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC.
- 6 - 1. Application range This specification is applied to LP78A chassis. 2. Requirement for Test Testing for standard of each part must be followed in below condition.
- 7 - 5. Model Specification(EU) Remark Full Scart 1EA, Harf 1EA Side AV Side AV S-Video Priority L/R Input(PC 1EA,SCART 2EA, SIDE AV 1EA, Component 1EA) Specification EU PAL BG/DK, PAL I/II, SECAM L/.
- 8 - 8. HDMI input (DTV) V-freq(kHz) 60.00 59.94 50.00 59.94 60.00 50.00 59.94 60.00 50.00 59.94 60.00 50.00 59.94 60 50 Proposed SDTV, DVD 480I(525I) SDTV, DVD 480I(525I) SDTV, DVD 576I(625I) 50Hz S.
- 9 - ADJUSTMENT INSTRUCTION 1. Application Range This spec sheet is applied all of the 26/32/37/42” LCD TV(LP78A) by manufacturing LG TV Plant all over the world. 2. Specification 1) Because this is not a hot chassis, it is not necessary to use an isolation transformer.
- 10 - => Select the "Bootloader.bat" file(install > VCTP_download > Bootloader) => Push "OK" => Finish the program, after saving the file "download_cs.vi2c" (if you click , the massage appears automatically) 4.
- 11 - 8) Click OK button at the "edit window". 9) Under Downloading process 10) If download is failed, for example "No acknowledge from slave". Execute download again from(1). (2) Download method 2 (AV Plate Ass’y) 1) Push S/W ‘ON" (connect SCL to GND using switch at Jig ) and connect the download jig to D-sub jack.
- 12 - 9) Choose the Hex file in folder and execute downloading with click "open button". 10) Click OK button at the "edit window" 11) Under Downloading progress. 12) If download is failed, for example "No acknowledge from slave", execute download again from (1).
- 13 - 7) Double click the download file low then, "edit" window will be opened. 8) Chick the choice button I n the "edit window", then "file choice window’ will be opened 9.
- 14 - (5) Push the Update NVM from File 4.4. T ool Option Area Option Change Before PCB check, have to change the Tool option and Area option Option values are below (If on changed the option, the input menu can differ the model spec.) The input methods are same as other chassises(Use adj Key on the Adjust Remote control) 4.
=> Detail EDID Options are below(a, b, c, d, e) a. Product ID b. Serial No : Controlled on production line c. Month, Year : Controlled on production line ex) Monthly: '03' => '03' Year: '2005' => '0F' d.
- 16 - (3) DDC adjustment support command set 6.3. Adjustment of White Balance (For Manual adjustment) - Operate the zero-calibration of the CA-110 or CA-210, then stick sensor to LCD module when you adjust.
- 17 - TROUBLESHOOTING 1. No power (1) Symptom 1) Minute discharge does not occur at module. 2) Front LED does not activate. (2) Press check Plug in the power cord Start Check No Yes Is the power cord plugged in? Connect the cable. Plasma(CN1) No Yes Are the line filter and PSU connected? Replace the fuse.
- 18 - 2. Protect mode (1) Symptom 1) After lighting once it does not discharge minutely from the module. 2) The relay falls.(there is an audible “Click”.) 3) The color of the front LED turns from green to red. (2) Follow check Is the Power Board normal ? Replace Power Board.
- 19 - 3. No Raster (1) Symptom 1) No OSD or image are displayed on the screen. 2) The front LED remains green. (2) Follow check 4. In the case an unusual display in RF mode.
- 20 - 5. In the case of an unusual display in rear A V mode. Is video input of the A/V jack normal? (Check R172) Yes Sam as Block A Check the input source. No 6. In the case of an unusual display in Side A V mode. Is the video input of the A/V jack normal? (Check CN703 Pin9) Yes Sam as Block A Check the input source.
- 21 - 8. In the case of an unusual display in SCART 1 mode. Is the video input of the A/V jack normal? (Check R172) Yes Sam as Block A Check the input source. No 9. In the case of an unusual display in SCART 1_RGB mode. Is the video input of the A/V jack normal?(Check R110,R170, R171, R173) Yes Sam as Block A Check the input source.
- 22 - 1 1. In the case of an unusual display in component 1 mode. Is the video input of the A/V jack normal? (Check R248, R249,R250) Yes Change the IC(IC500) Check the input source. No 12. In the case of an unusual display in component 2 mode. Yes Change the IC(IC500) Check the input source.
- 23 - 14. No Sound (1) Symptom 1) LED is green. 2) There is a picture but no sound. (2) Follow check Is there sound in any mode? Is the speaker on? Yes Yes Is the speaker cable normal? Yes Yes Is the.
- 24 - 15. HDMI mode Is only video normal? Is only audio normal? No Yes Download EDID data each port. Check the TMDS line wave. (R312~E3273) 1. Check the HDMI receiver’s status register. (0x60, offset 0x66) - If the value is 0xf or 0x8, it is normal.
- 25 - HDMI BLOCK DIAGRAM Downloaded From TV-Manual.com Manuals.
- 26 - 530 531 532 590 591 120 120 300 200 600 210 220 202 580 520 250 240 230 401 430 403 400 402 EXPLODED VIEW Downloaded From TV-Manual.com Manuals.
Downloaded From TV-Manual.com Manuals.
Downloaded From TV-Manual.com Manuals.
Downloaded From TV-Manual.com Manuals.
Mar., 2007 Printed in Korea P/NO : MFL36696905 Downloaded From TV-Manual.com Manuals.
デバイスLG Electronics 32LC41/4R-ZAの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
LG Electronics 32LC41/4R-ZAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLG Electronics 32LC41/4R-ZAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。LG Electronics 32LC41/4R-ZAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。LG Electronics 32LC41/4R-ZAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
LG Electronics 32LC41/4R-ZAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLG Electronics 32LC41/4R-ZAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、LG Electronics 32LC41/4R-ZAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLG Electronics 32LC41/4R-ZAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
