Appleメーカー5200CDの使用説明書/サービス説明書
ページ先へ移動 of 319
Service Source K Po wer Macintosh/Performa 5200 and 5300 (not 5260, 5280) Power Macintosh 5200/75 LC, 5300/100 LC Performa 5200CD, 5215CD,5300CD International Performa 5320CD.
Service Source K Basics Po wer Macintosh/Performa 5200 and 5300 (not 5260, 5280).
Basics System Overview - 1 System Overview The Power Macintosh 5200/5300 computer series combines RISC-based PowerPC performance, full multimedia features, and low cost in a sleek all-in-one design. The design includes expansion slots for 68040 LC communications and PDS cards, as well as other video-in, video tuner, and video-out options.
Basics Rev. B, 5000 Series - 2 Rev. B, 5000 Series Apple introduced an updated 5000 series version several months after introduction. Referred to in this manual as “Rev. B,” the updated version incorporates design changes that are not backward-compatible.
Basics Rev. B, 5000 Series - 3 Another way to identify a 5200 series version A and Rev. B is to look at the back of the computer for the part number and manufacture date. The label with this information is on the lower part of the plastic case. Version A contains one of these numbers: 620-0635 or 620-0835.
Basics Performa 5320CD - 4 Performa 5320CD The Performa 5320CD supersedes the 5300CD. It has a PowerPC 603e processor running at 120 MHz and 16 MB of RAM on the logic board. All other hardware features are the same as the Performa 5300CD. This is an international product not sold in the U.
Basics Open Transport - 5 Open Transport Open Transport 1.1 does not work on 5200 or 5300 Series computers. These computers require Open Transport 1.1.1. When version 1.1.1 is installed on these computers, a dialog box may appear indicating that a hardware issue was detected.
Basics Service Strategy - 6 Service Strategy Service the Power Macintosh/Performa 5000 series through module exchange and parts replacements. Customers can request on-site service from an Apple Authorized Service Provider Plus (AASP+) or Apple Assurance.
Basics Service Strategy - 7 orders placed through the AppleOrder system. Service Providers not enrolled in AppleOrder may fax their orders to Service Provider Support (512-908-8125) or mail them to Apple Computer, Inc.
Basics Service Strategy - 8 Diagnostics Use MacTest Pro for Power Macintosh to perform diagnostics on the Power Macintosh/Performa 5000 series. Design f or Serviceability To access the floppy drive, CD-ROM drive, or front panel control board, remove the drive and controls bezel.
Basics User Controls - 9 User Controls User controls include • Soft power-on control from keyboard • Front-panel sound-control pushbuttons • Front-panel brightness-control pushbuttons • Option.
Basics Internal Expansion Connections - 1 0 Internal Expansion Connections Expansion connections on the logic board include • 2 DRAM SIMM expansion slots • LC Processor Direct Slot (PDS) • Commu.
Basics Intelligent Device Electronics (IDE) Hard Drive - 11 Intelligent Device Electronics (IDE) Hard Drive The internal hard drive uses Intelligent Device Electronics (IDE) technology, commonly used in DOS-compatible systems. The IDE hard drive functions the same as a typical SCSI hard drive.
Basics Processor Direct Slot (PDS) - 12 Processor Direct Slot (PDS) The LC-PDS is compatible with the PDS in the Macintosh LC family of computers, but it is not a true PDS.
Basics Video-In Card - 13 Video-In Card The Video-In Card is an optional card included with the Apple Video System. It allows users to digitize video from the TV Tuner, MPEG Card, and external composite or S-video inputs. It accepts NTSC, PAL, or SECAM format video and also provides stereo audio inputs.
Basics MPEG Card - 14 MPEG Card The MPEG Card is an optional card included with the Apple MPEG Media System. The MPEG Card requires that the Video-In Card be installed. It provides hardware decompression for MPEG movie files, enabling full-screen (through pixel doubling), 30-frames-per-second, 24-bit video playback with 16-bit audio.
Basics TV Tuner Module - 1 5 TV Tuner Module The TV Tuner, an optional module included with the Apple TV/Video System, turns the computer into a television receiver. The TV Tuner requires the Video-In Card, which is also included with the Apple TV/Video System.
Basics TV/FM Radio Tuner Card - 1 6 TV/FM Radio Tuner Card The TV/FM radio tuner card turns the computer into a television and FM radio receiver, complete with remote control. An expansion ribbon connector for the optional TV/FM radio tuner card provides NTSC and PAL input from an external TV antenna or cable.
Basics TV/FM Radio Tuner Card - 1 7 The TV picture is in its own window on the desktop, and the default size of the window is 320x240 pixels. The picture can be resized from 160x120 pixels up to 640x480 pixels.
Basics TV/FM Radio Tuner Card - 1 8 The card is available in versions for NTSC, PAL, and SECAM television systems. The features of the TV tuner include the following: • Remote tuner for 181 broadcast and cable channels (U.S. version) • Coaxial connector for TV antenna or cable input (F-type connector in U.
Basics TV/FM Radio Tuner Card - 1 9 The features of the FM radio tuner include the following: • FM radio frequencies received and displayed • Stations scanned and searched up and down the frequenc.
Basics External Video Connector - 2 0 External Video Connector The External Video Connector is an optional module that provides the computer with video output (mirroring). Install the External Video Connector in a dedicated 3/4-inch, 22-pin slot on the logic board.
Basics Apple Presentation System - 2 1 Apple Presentation System The Apple Presentation System (APS) is an external module that uses the 15-pin video output connector on the computer, and then provides a video signal for a separate television display or for recording on a VCR.
Basics CRT and Degauss Frame - 2 2 CRT and Degauss Frame The CRT and degauss frames are precisely matched at the factory and must be removed and replaced as a unit.
Basics Front View - 23 Front View Mouse Built-In Microphone Color Display Headphone Jack Floppy Disk Drive Sound Control Buttons Screen Control Buttons Keyboard CD-ROM Drive (optional) Power-On Light .
Basics Rear View - 24 Rear View Microphone Assembly Analog Board Assembly CD ROM Drive Logic Board I/O Panel Assembly Tilt-Swivel Assembly Hard Drive Floppy Drive CRT Video Board Assembly Power Su.
Basics I/O Panel - 25 I/O Panel PDS Cover Communication Card Access Cover SCSI Port Printer Port Modem Port ADB Port Sound Input Port Sound Output Port Video Input Access Cover External Video Output C.
Basics 5200 Logic Board - 2 6 5200 Logic Board DRAM SIMM Slots PDS Communications Card Slot Battery Video-In Slot Monitor-Out Slot ROM Slot.
Basics 5300 Logic Board - 2 7 5300 Logic Board DRAM SIMM Slots PDS Communications Card Slot Battery Video-In Slot Monitor-Out Slot ROM Slot Processor with Heatsink.
Service Source K Specifications Po wer Macintosh/Performa 5200 and 5300 (not 5260, 5280).
Specifications Processor - 1 Processor CPU 5200 Series PowerPC 603 processor 75 MHz 5300 Series (except 5320) PowerPC 603e processor 100 MHz 5320 PowerPC 603e processor 120 MHz Addressing 64-bit Power.
Specifications Memory - 2 Memory DRAM 5200 and 5300 Series (except 5320) 8 MB DRAM, minimum, in one SIMM slot (No RAM soldered on board) Expandable to 64 MB in two SIMM slots (72-pin, 80 ns or faster .
Specifications Memory - 3 Frame Buffer 1 MB DRAM on board, for video support RO M 4 MB Cache Memory 256K Level 2.
Specifications Disk Storage - 4 Disk Storage Floppy Drive 1.4 MB Apple SuperDrive Manual Insert Hard Drive 5200 Series 500 MB, 700 MB, or 1 GB IDE hard drive 5300 Series 1.
Specifications I/O Interfaces - 5 I/O Interfaces Serial Two RS-232/422 serial ports for modem and printer (mini DIN-8 connectors) LocalTalk supported SCSI One external SCSI port (DB-25 connector) Supp.
Specifications I/O Interfaces - 6 Sound Output Two stereophonic sound output ports, level nominally 0.5 V RMS into 39 ohms One front headphone jack, one rear stereo mini phonejack Internal stereo speakers External V ideo Connector One DB-15 mirror video out connector using optional video connector kit.
Specifications I/O Interfaces - 7 Communications One 112-pin internal expansion slot for modem or Ethernet card (68040-bus configuration) Processor -Direct Slot One 96/114-pin internal expansion slot .
Specifications I/O Devices - 8 I/O De vices K eyboard AppleDesign Keyboard, Apple Extended Keyboard (other ADB keyboards supported) Mouse Apple Desktop Bus Mouse II Mechanical tracking, optical shaft,.
Specifications Sound and Video - 9 Sound and V ideo Sound Generator Records at 11-kHz or 22-kHz sample rate Plays back at 22-kHz sample rate Two speakers with enhanced stereo sound Allows playback and.
Specifications Sound and Video - 1 0 Built-in V ideo Display Dot Pitch: 0.28 mm Vertical Frequency: 66.7 Hz Active Raster Size (nominal): 9.5 in. by 7.3 in. (240 mm by 185 mm) White Point: 9,300° K Shipping Brightness (nominal): 25-foot lamberts 15-inch Shadow Mask display (12.
Specifications Sound and Video - 1 1 V ideo Modes Support these video modes: 640x480 resolution with 16-bit color 800x600 resolution with 8-bit color 832x624 resolution with 8-bit color (does not supp.
Specifications Sound and Video - 1 2 Monitor Timings 640x480 Resolution at 60 Hz Horizontal Timing Back Porch: 48 dots H SYNC: 96 dots Front Porch: 16 dots 1 dot: 39.72 ns 1 H: 31.77 ms 1/dot: 25.175 MHz V ertical Timing Back Porch: 33 H V SYNC: 2 H Front Porch: 10 H 1 H: 31.
Specifications Sound and Video - 1 3 Monitor Timings 640x480 Resolution at 66.67 Hz Horizontal Timing Back Porch: 96 dots H SYNC: 64 dots Front Porch: 64 dots 1 dot: 33.06878 n 1 H: 28.5714 ms 1/dot: 30.24 MHz V ertical Timing Back Porch: 39 H V SYNC: 3 H Front Porch: 3 H 1 H: 28.
Specifications Sound and Video - 1 4 Monitor Timings 800x600 Resolution at 60 Hz Horizontal Timing Back Porch: 88 dots H SYNC: 128 dots Front Porch: 40 dots 1 dot: 25.000 ns 1 H: 26.4 ms 1/dot: 40.000 MHz V ertical Timing Back Porch: 23 H V SYNC: 4 H Front Porch: 1 H 1 H: 37.
Specifications Sound and Video - 1 5 Monitor Timings 800x600 Resolution at 72 Hz Horizontal Timing Back Porch: 64 dots H SYNC: 120 dots Front Porch: 56 dots 1 dot: 20.000 ns 1 H: 20.800 ms 1/dot: 50.000 MHz V ertical Timing Back Porch: 23 H V SYNC: 6 H Front Porch: 37 H 1 H: 20.
Specifications Sound and Video - 1 6 External V ideo Connector (Optional) Supports video mirroring on the following external monitors (at product introduction): • 640x480 resolution: Macintosh 12-in.
Specifications Electrical - 1 7 Electrical Line V oltage 100–240 VAC Frequency 47–63 Hz Po wer 125 W Surge Voltage: 300 V rms for 100 ms Peak Inrush Current: 40 A pk Current: 2.
Specifications Physical - 1 8 Physical Dimensions Height: 17.5" (445 mm) Width: 16" (406 mm) Depth: 15.1" (383 mm) W eight Without CD-ROM: 17 lb.
Specifications Environmental - 19 En vironmental T emperature Operating: 50°–104° F (10°–40° C) Transit (72 hours): –40° F to +149° F (–40° C to +65° C) Storage (6 months): –40° F to +116° F (–40° C to +47° C) Humidity Noncondensing, 20–95% Altitude 0–10,000 ft.
Service Source K Troubleshooting Power Macintosh/Performa 5200 and 5300 (not 5260, 5280).
Troubleshooting General - 1 General The Symptom Charts included in this chapter will help you diagnose specific symptoms related to your product. Because cures are listed on the charts in the order of most likely solution, try the first cure first. Verify whether the product continues to exhibit the symptom.
Troubleshooting First Checklist - 2 First Checklist Jitter, faint lines, or screen movement can be caused by external interference such as electronic devices and fluorescent lights. Move the unit to another room or building to help determine if external interference is the source of the problem.
Troubleshooting Symptom Charts/ System - 3 Symptom Charts System System intermittently crashes or hangs 1 Verify that system software is version 7.5 or later. 2 Verify that software is compatible with system. 3 If clock chip at U10 is not p/n 343S1191 or 343S1121, replace logic board.
Troubleshooting Symptom Charts/ System - 4 Figure 1: ROM DIMM Logic Board ROM DIMM Chip at U10 No Sticker.
Troubleshooting Symptom Charts/ System - 5 System does not start up 1 Reset logic board. Refer to Additional Procedures. 2 Replace power supply. 3 Check power cord connection. 4 Replace logic board. Retain customer’s SIMMs. System will not start up from keyboard, but will start up from rear power switch 1 Verify keyboard as known-good.
Troubleshooting Symptom Charts/ System - 6 Flashing “?” appears at startup in system with vacant PDS and communications slots 1 Diagnose hard drive with Disk First Aid included on Power Macintosh CD-ROM. 2 Perform repairs, and then go to step 4. 3 If repairs are impossible, back up drive, reformat with Drive Setup 1.
Troubleshooting Symptom Charts/ System - 7 . Figure 2: Identifying Version B Logic Boards Apple Computer Inc. @199X XXX-XXXX-B Apple Computer Inc. @199X XXX-XXXX-B No Picture of Texas U6 Part No.
Troubleshooting Symptom Charts/ System - 8 Menu bar constantly flashes or system constantly beeps 1 Verify that front-panel control buttons are not jammed. 2 Verify “mute” is not selected in the Sound control panel. 3 Reseat drive bezel and front-panel control board.
Troubleshooting Symptom Charts/ Audio - 9 Audio Distorted or garbled sound from both speakers Replace analog/video board assembly. Distorted or garbled sound from one speaker 1 Replace defective speaker. 2 Replace analog/video board assembly. Sound distortion with MPEG board installed Replace MPEG board with modified MPEG board.
Troubleshooting Symptom Charts/ Audio - 1 0 Crackling noise is present when playing sounds other than system beeps and not in “play through” mode 1 If static noise varies while adjusting volume with Sound control panel, use Audio Volume Extension 1.
Troubleshooting Symptom Charts/ Video - 1 1 Video Screen is black, too dark, or too bright; audio and drive operate 1 Adjust contrast button on front bezel. 2 Adjust brightness. Use Screen control panel. 3 Check yoke cable connection. 4 Perform video adjustments.
Troubleshooting Symptom Charts/ Video - 1 2 Video will not play or system hangs when attempting to run video in units with MPEG card 1 If chip at location U12 on MPEG card displays number 341SO205, check all connections. 2 If chip at location U12 on MPEG card does not display number 341SO205, replace MPEG card.
Troubleshooting Symptom Charts/ Video - 1 3 Picture breaks into diagonal lines, or picture rolls vertically or horizontally 1 Perform geometry adjustments. Refer to “Geometry” in Adjustments chapter. 2 Replace analog/video board assembly. Out of convergence (color bleeds from text or lines) 1 This problem rarely indicates a defective module.
Troubleshooting Symptom Charts/ Video - 1 4 Screen jitters or flashes 1 Refer to “First Checklist” in Troubleshooting chapter. Move electrical devices (other monitors, scanners, and so on) away from monitor. Temporarily shut off all fluorescent lights in area.
Troubleshooting Symptom Charts/ Video - 1 5 Raster size too short/ tall or narrow/wide Install monitor adjustment cable, and set appropriate on-screen video adjustment controls to vertical height of 185 mm (7.3 inches) and to horizontal width of 240 mm (9.
Troubleshooting Symptom Charts/ Video - 1 6 Raster distorted (barrel-shaped, corners not square, stretched or compressed at top of display, or sides not perpendicular) 1 Refer to “First Checklist” in Troubleshooting chapter. 2 Perform appropriate geometric adjustments.
Troubleshooting Symptom Charts/ Video - 1 7 Screen has white areas with blotches of color 1 Refer to “First Checklist” in Troubleshooting chapter. 2 Because this purity problem can be caused by magnetic fields, move unit to another location. 3 Degauss display with manual degaussing coil.
Troubleshooting Symptom Charts/ Floppy Drive - 18 Floppy Drive Audio and video are present, but internal floppy drive does not operate 1 Replace bad disk with known-good disk.
Troubleshooting Symptom Charts/ Floppy Drive - 19 Disk does not eject 1 Insert opened paper clip into hole beside floppy drive. 2 Switch off system and hold mouse button down while switching system on (to complete eject cycle). 3 Replace floppy drive.
Troubleshooting Symptom Charts/ Hard Drive - 20 Hard Drive Internal or external hard drive does not operate 1 Verify that all hard drive connections are secure. 2 Verify that external drive is properly terminated. 3 Reseat logic board. 4 Replace internal IDE hard drive.
Troubleshooting Symptom Charts/ CD-ROM Drive - 21 CD-ROM Drive CD-ROM drive does not accept disc 1 Exchange compact disc (if disc is dirty or damaged). 2 Replace CD-ROM drive mechanism. 3 Replace SCSI data cable. Volume control does not operate correctly 1 Check Sound control panel setting.
Troubleshooting Symptom Charts/ CD-ROM Drive - 22 Computer cannot mount known-good CD-ROM drive 1 Reseat CD-ROM drive adapters. 2 Check SCSI ID setting.
Troubleshooting Symptom Charts/ CD-ROM Drive - 23 Eject button sticks. Replace the front bezel (P/N 922-1398 Rev. A or P/N 922- 1857 Rev. B)..
Troubleshooting Symptom Charts/ Peripheral - 24 Peripheral Cursor does not move 1 Restart system. 2 Check mouse connection. 3 If mouse was connected to keyboard, connect mouse to rear ADB port and disconnect keyboard. If mouse works, replace keyboard.
Troubleshooting Symptom Charts/ Peripheral - 25 Cannot double-click to open application, disk, or server 1 Remove extra system files on hard drive. 2 Check mouse speed on Control Panel. 3 Unplug 4.5 battery, wait 20 seconds, plug in battery, and restart computer.
Troubleshooting Symptom Charts/ Peripheral - 26 Known-good StyleWriter, ImageWriter, or ImageWriter II does not print 1 Verify that Chooser and Control Panel are set correctly. 2 Verify that printer driver and system software are not corrupt. 3 Verify system software is version 7.
Troubleshooting Symptom Charts/ Miscellaneous - 2 7 Miscellaneous Clicking, chirping, or thumping sound 1 Replace analog board. 2 Replace logic board. Retain customer’s SIMMs. Smoke or Odor Present 1 Replace Analog board. 2 Replace Power Supply. 3 Replace Logic Board.
Troubleshooting Symptom Charts/ Miscellaneous - 2 8 Screen shows “Sad Macintosh” icon and black vertical lines; screeching sound 1 Replace RAM SIMMs on logic board.
Troubleshooting Symptom Charts/ Miscellaneous - 2 9 “Sad Macintosh” icon 1 Verify that no disc is in CD-ROM drive. 2 Disconnect all external SCSI devices and attempt to restart computer. 3 Disconnect internal SCSI device and attempt to start computer with known-good floppy disk.
Troubleshooting Symptom Charts/ Miscellaneous - 30 System with internal modem unable to recognize graphics or Ethernet card in communications slot 1 Replace internal modem.
Troubleshooting Symptom Charts/ Global Village Modem “Busy Serial Port” - 31 Global Village Modem “Busy Serial Port” Using modem gives message: “Can’t find or can’t access a modem to use for registration. Make sure you have Global Village software installed correctly, reboot your computer, and try again.
Troubleshooting Symptom Charts/ Global Village Modem “Busy Serial Port” - 32 Resetting modem in TelePort Control Panel gives message: “The current port is busy and cannot be opened.
Service Source K T ake Apart Po wer Macintosh/Performa 5200 and 5300 (not 5260, 5280).
Take Apart Drive and Control Bezel - 1 Drive and Control Bezel No preliminary steps are required before you begin this procedure..
Take Apart Drive and Control Bezel - 2 1 P l a cing your fingertips in the holes of the finger latches, pull the two finger latches down. 2 Swing the drive and control bezel up and off.
Take Apart Drive and Control Bezel - 3 Replacement Note: Insert the drive bezel hinge tabs behind the upper corners of the front bezel opening. Swing the drive bezel down until it snaps closed.
Take Apart Floppy Drive - 4 Floppy Drive Before you begin, remove the drive and control bezel. Caution: Review the ESD precautions in Bulletins/ Safety.
Take Apart Floppy Drive - 5 1 Pull up the release latch, and pull out the floppy drive far enough to reach the ribbon cable connector..
Take Apart Floppy Drive - 6 2 Disconnect the floppy drive from the floppy drive cable. Note: Remove the drive carrier if you are replacing the floppy drive. Note: Because screw placement varies according to the type of drive used with the carrier, note the placement of the screws before removing them.
Take Apart Floppy Drive - 7 3 Remove the four mounting screws. 4 Remove the carrier from the floppy drive..
Take Apart CD-ROM Drive - 8 CD-ROM Drive Before you begin, remove the following: • Drive and control bezel • Floppy drive Note: The CD-ROM drive is optional.
Take Apart CD-ROM Drive - 9 Push up the release latch and pull the CD-ROM drive from the chassis. Note: You may need to use some initial force to disconnect the CD-ROM drive from the internal chassis/wiring harness.
Take Apart CD-ROM Drive - 10 Note: Perform the following steps only if you are replacing the CD-ROM drive. 1 Disconnect the CD-ROM audio adapter from the drive. 2 Disconnect the SCSI adapter. 3 Remove the four mounting screws and carrier from the CD- ROM drive.
Take Apart CD-ROM Drive - 11 Replacement Note: Retain the carrier, screws, and adapters for installation on the new drive. Replacement Caution: Before replacing the SCSI adapter, verify that the SCSI drive connector pins are not bent.
Take Apart Front Panel Control Board - 1 2 Front Panel Control Board Before you begin, remove the drive and control bezel. Caution: Review the ESD precautions in Bulletins/ Safety.
Take Apart Front Panel Control Board - 1 3 Caution: Be sure to grip the front panel in the area shown to avoid harming circuit t racings. 1 Using needle-nose pliers, grip the front edge of the front-panel control board. 2 Pull firmly and slide the front panel control board out far enough to reach the ribbon cable connector.
Take Apart Front Panel Control Board - 1 4 3 Disconnect the cable from the front-panel control board. Replacement Note: Using a flat-blade screwdriver, press the front-panel control cable back and down.
Take Apart Front Panel Control Board - 1 5 Replacement Note: Tilt the board up slightly to insert it into the guide rails..
Take Apart Front Panel Control Board - 1 6 Replacement Note: The front edge of the reinstalled front-panel control board must be flush with the front edge of the plastic chassis.
Take Apart I/O Door - 1 7 I/O Door No preliminary steps are required before you begin this procedure..
Take Apart I/O Door - 1 8 1 Remove the two security screws..
Take Apart I/O Door - 1 9 2 Using your fingertips, pull the two finger latches down. 3 Swing the door up and off. Replacement Note: Align the I/O door hinge tabs and slide the door up into position.
Take Apart Logic Board - 2 0 Logic Board Before you begin, remove the I/O door. Caution: Review the ESD precautions in Bulletins/ Safety..
Take Apart Logic Board - 2 1 1 Swing out the handle from its storage position. 2 Pull out the lo gic board. Note: When installing cards, cover the two screws (for fan support and ground thermistor mounting) with tape. These screws are below the upper chassis, in the area of the logic board.
Take Apart Logic Board - 2 2 Note: Perform the following steps only if you are replacing a defective logic board. 3 Remove the two Phillips screws that secure the fence to the solder side of the logic board.
Take Apart Logic Board - 2 3 4 Using a hex nut driver, remove the two hex nuts that secure the logic board fence to the SCSI connector. 5 Separate the logic board fence from the logic board.
Take Apart Logic Board - 2 4 Replacement Note: Refer to the logic board note in the Parts chapter to distinguish the 8-bit-sound logic board from the 16-bit-sound logic board. Replacement Note: You may need to remove the 603e processor on the 5300 series logic board to install SIMMs.
Take Apart Logic Board - 2 5 shield. Align the flange around the mini-DIN shield first, then swing the rest of the logic board fence into place..
Take Apart Rear Housing - 2 6 Rear Housing Before you begin, remove the I/O door. ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. There are two versions, the original version and Rev.
Take Apart Rear Housing - 2 7 The original rear housing is not forward- compatible with Rev. B units. The Rev. B rear housing is backward- compatible with original units. 1 Pry off the two screw covers on each side of the rear housing. : Pry up from the rear edge of the screw cover.
Take Apart Rear Housing - 2 8 2 Remove the three torx screws on each side of the rear housing..
Take Apart Rear Housing - 2 9 3 ± W arning: This step exposes high voltage components. Follow CRT safety precautions. Slide the rear housing back and off.
Take Apart Front Bezel - 3 0 Front Bezel Before you begin, remove the following: • I/O door • Rear housing ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Front Bezel - 3 1 an original or Rev. B version. The Rev. B and original versions of the front bezels are not interchangeable. 1 Note: The speaker cable is the set of two gray, round cables wrapped around the ferrite bead. Disconnect the speaker cable and guide it down and under the metal CRT frame.
Take Apart Front Bezel - 3 2 2 Disconnect the microphone cable and guide the cable to the microphone side of the metal CRT frame. 3 Pull off the front bezel.
Take Apart Front Bezel - 3 3 Replacement Note: Guide the microphone cables through the plastic retainers before replacing the front bezel. : Guide the speaker cable connector behind the metal CRT frame, and then up to the speaker connector on the main deflection board.
Take Apart Internal Microphone - 34 Internal Microphone Before you begin, remove: • I/O door • Rear housing • Front bezel ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Internal Microphone - 35 LIft off the microphone. Replacement Note: Guide the microphone cable through the plastic cable retainers..
Take Apart Rear EMI Shield - 36 Rear EMI Shield Before you begin, remove the following: • I/O door • Rear housing • Front bezel ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Rear EMI Shield - 37 is considerably larger, but removal procedures are similar. : Original and Rev. B rear EMI shields are not interchangeable.
Take Apart Rear EMI Shield - 38 1 Remove the four screws from the rear shield..
Take Apart Rear EMI Shield - 39 2 Swivel the rear shield up and lift off. Replacement Note: Insert the two corner hinge tabs into the slots of the power supply and analog board shields.
Take Apart Speakers, Original Version - 4 0 Speakers, Original Version Before you begin, remove the following: • I/O door • Rear housing • Front bezel ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Speakers, Original Version - 4 1 The Power Macintosh/Performa 5000 series includes two versions, the original version and Rev. B. See the Rev. B topic of the Basics chapter to identify the version you are servicing. The speakers of the two versions are not interchangeable and the Take Apart procedures differ significantly.
Take Apart Speakers, Original Version - 4 2 follow the procedures in “Speakers, Rev. B.” 1 Place the front bezel face down. 2 Remove the speaker cables from the plastic cable retainers on the inside of the front bezel.
Take Apart Speakers, Original Version - 4 3 Replacement Note: Place the speaker with the longer cable on the floppy drive side of the unit. Align and secure the speaker with the bottom tabs inside the bezel. Then snap the top of the speaker over the two security pins.
Take Apart Speakers, Rev. B - 4 4 Speakers, Rev. B Before you begin, remove the following: • I/O door • Rear housing • Front bezel.
Take Apart Speakers, Rev. B - 4 5 The Power Macintosh/Performa 5000 series includes two versions, the original version and Rev. B. See the Rev. B topic of the Basics chapter to identify the version you are servicing. The speakers of the two versions are not interchangeable and the Take Apart procedures differ significantly.
Take Apart Speakers, Rev. B - 4 6 1 Press the tab and release the speaker from the chassis slot..
Take Apart Speakers, Rev. B - 4 7 2 Tilt the speaker and remove it..
Take Apart Speakers, Rev. B - 4 8 Replacement Note: • The plastic speakers are printed “right” and “left.” Place the speakers accordingly as you face the monitor. • Guide the wire connecting the speakers in the channel between the monitor and chassis.
Take Apart Hard Drive - 49 Hard Drive Before you begin, remove the I/O door. Caution: Review the ESD precautions in Bulletins/ Safety..
Take Apart Hard Drive - 50 1 Using the convenience pull tab, disconnect the IDE data cable from the hard drive connector. 2 Disconnect the power cable.
Take Apart Hard Drive - 51 3 Using needle-nose pliers, pull up the release latch and slide the IDE hard drive from the chassis. Replacement Caution: Some hard drives have sharp edges near the cable connector that can rub and, therefore, damage the cable.
Take Apart Hard Drive - 52 Note: Perform the following steps only if you are replacing the hard drive. Note: Notice the placement of the carrier and screws before removing them. Retain the carrier and screws, and install them on the new hard drive. 4 Remove the four screws.
Take Apart TV Tuner - 5 3 TV Tuner Before you begin, remove the following: • I/O door • Logic board Note: The TV Tuner is an option. Caution: Review the ESD precautions in Bulletins/ Safety.
Take Apart TV Tuner - 5 4 1 Remove the Phillips s c rew. 2 Slide out the TV Tuner far enough to reach the TV Tuner cable..
Take Apart TV Tuner - 5 5 3 Disconnect the TV Tuner cable and remove the TV Tuner..
Tak e Apart Power Supply, Rev. A - 5 6 Power Supply, Rev. A Before you begin, identify if you have a Rev. A or Rev. B power supply. Refer to the Parts Database or the next page to identify the board. If you are servicing a Re v . A board, continue with these procedures.
Take Apart Power Supply, Rev. A - 57 There are two Rev. A versions and one Rev. B version of the Power Supply. • Rev. A 661-0331 with a thermistor at CN13 • Rev. A 661-0930 without a thermistor at CN13 • Rev. B 661-1117 with a thermistor at CN9 These power supplies are NOT interchangeable.
Take Apart Power Supply, Rev. A - 58 1 Remove the screw and grounding cable from the upper front corner of the power supply shield..
Take Apart Power Supply, Rev. A - 59 2 Remove the screw from the lower rear corner of the power supply shield. Power Supply EMI Shield Screw.
Take Apart Power Supply, Rev. A - 60 3 Slide the power supply shield back to clear the interlocking tab and remove the shield. Replacement Note: Slide the interlocking tab into the slot of the CRT metal frame.
Take Apart Power Supply, Rev. A - 61 4 Remove the screw and short grounding cable from the lower rear corner of the power supply. Ground Cable Screw.
Take Apart Power Supply, Rev. A - 62 5 Lift the lower rear corner of the power supply board to disengage the lower rear bracket. 6 Slide the top front corner from the CRT frame bracket.
Take Apart Power Supply, Rev. A - 63 7 Disconnect the 2-pin degauss cable. 2-Pin Degauss Cable.
Take Apart Power Supply, Rev. A - 64 8 Disconnect these cables: • 2-pin fan cable (CN5) • 14-pin power cable (CN6) • 10-pin video cable (CN7).
Take Apart Power Supply, Rev. A - 65 Note: The power supply-to-analog-board connectors are keyed and fit very tightly. You may need to use a jeweler’s screwdriver to loosen the sockets of these connectors.
Take Apart Power Supply, Rev. A - 66 Replacement Note: This diagram shows the location of the rear bracket and the power supply cable connections for the Rev.
Take Apart Power Supply, Rev. A - 67 • 10-pin power-supply- to-analog-board cable (CN7) • 2-pin degauss cable (CN2) • 2-pin fan thermistor connector (CN13) Note: The thermistor is not present on the 661-0930 Rev. A power supply board. Replace power supply boards like-for-like.
Take Apart Power Supply, Rev. B - 68 Power Supply, Rev. B Before you begin, remove the following: • I/O door • Rear housing • Front bezel • Logic board • Rear EMI shield ± Warning: This product contains high voltage and a high-vacuum picture tube.
Take Apart Power Supply, Rev. B - 69 Follow the removal procedures in “Power Supply, Rev. A” but use the diagram of power supply Rev. B connections. The Power Macintosh/Performa 5000 series have three power supply versions, two Rev. A boards and a Rev.
Take Apart Power Supply, Rev. B - 70 Rev B: Disconnect: • 2-pin degauss cable (CN3) • 2-pin cable (CN2) • 2-pin fan thermister cable (CN9) • 2-pin fan connector (CN8) • 14-pin power supply cable (CN4) Note: The pull-up tab (CN5) is fragile. • 10-pin ribbon cable (CN5) • 6-pin cable (CN6) • 10-pin cable (CN7) Rear Bracket Rev.
Take Apart Video Board - 7 1 Video Board Before you begin, • Remove the rear housing • Remove the front bezel • Remove the logic board • Remove the rear EMI shield • Discharge the CRT • Re.
Take Apart Video Board - 7 2 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. Note: Do not disconnect the cables connecting the video board and the analog board.
Take Apart Video Board - 7 3 The analog/video board assemblies of the two versions are not interchangeable. 1 If an adhesive glue secures the video board to the CRT, cut and peel it off before removing the board. 2 Caution: Do not attempt to disconnect the video board from the analog board.
Take Apart Video Board - 7 4 service unit. Pull off the video board. 3 Remove the two long grounding cables from the video board. 4 Remove the single short grounding cable from the video board.
Take Apart Analog Shield - 7 5 Analog Shield Before you begin, • Remove the rear housing • Remove the front bezel • Remove the logic board • Remove the rear EMI shield • Discharge the CRT • Remove the anode cap • Remove the video board ± W arning: This product contains high voltage and a high-vacuum picture tube.
Take Apart Analog Shield - 7 6 1 Remove the grounding cable and screw from the upper front corner of the analog board shield. 2 Remove the screw from the lower rear side of the analog board shield.
Take Apart Analog Shield - 7 7 3 Slide the analog board shield back to clear the interlocking tabs and side runners. 4 Remove the analog board shield. Interlocking Tab Side Runners Analog Shield.
Take Apart Analog Board, Original Version - 7 8 Analog Board, Original Version Before you begin, • Remove the front bezel • Remove the I/O door • Remove the rear housing • Remove the logic boa.
Take Apart Analog Board, Original Version - 7 9 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. Note: Do not disconnect the cables connecting the video board and the analog board.
Take Apart Analog Board, Original Version - 8 0 The analog/video board assemblies of the two versions are not interchangeable. If you are servicing an original version, use the following procedures. If you are servicing a Rev. B version, use the following procedures, but substitute the cable locations in “Analog Board, Rev.
Take Apart Analog Board, Original Version - 8 1 1 Remove the screws at the lower rear of the analog board..
Take Apart Analog Board, Original Version - 8 2 2 Lift up the lower back corner of the board to disengage the rear bracket from the chassis slot. 3 Slide the analog board back to clear the interlocking tab and lift it from the guide rail.
Take Apart Analog Board, Original Version - 8 3 security rail and rest the analog board on the top of the chassis. 5 Note: For a diagram of analog board cable connections, refer to the replacement note at the end of this topic. Disconnect the yoke cable at the power supply.
Take Apart Analog Board, Original Version - 8 4 6 Disconnect these cables from the analog board: • 6-pin power-supply- to-analog-board cable (P102) • 10-pin power- supply-to-analog- board cable (P704) • Logic board connector cable (P101) • Single-pin degauss cable 7 Remove the analog and video boards assembly.
Take Apart Analog Board, Original Version - 8 5 Replacement Note: This d i agram shows the location of the rear bracket and the analog board cable connections: • Rear bracket • Degauss cable • L.
Take Apart Analog Board, Rev. B - 8 6 Analog Board, Rev. B The Power Macintosh/Performa 5000 series includes two versions, the original version and Rev.
Take Apart Analog Board, Rev. B - 8 7 The analog and video boards of the two versions are not interchangeable. If you are servicing a Rev. B version, use the procedures in “Analog Board, Original Version” and substitute the following cable locations.
Take Apart Analog Board, Rev. B - 8 8 Disconnect these video board cables: • Ground cable from the exterior tab of the video board • Black grounding connection (P306) • 10-pin ribbon cable (P301) Rev.
Take Apart Analog Board, Rev. B - 8 9 Disconnect these cables: • 2-pin flyback connector from power supply location CN2/J6 • 4-pin yoke cable (P701) • 4-pin speaker wire (P803) • 4-pin mic cab.
Take Apart Internal RGB Cable - 90 Internal RGB Cable Before you begin, • Remove the I/O door • Remove the rear housing • Remove the rear EMI shield • Discharge the CRT • Remove the anode ca.
Take Apart Internal RGB Cable - 91 ± Warning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. 1 Disconnect the internal RGB cable at the P703 connector on the analog board and at the P301 connector on the video board.
Take Apart Fan - 9 2 Fan Before you begin, • Remove the I/O door • Remove the rear housing • Remove the front bezel • Remove the rear EMI shield • Discharge the CRT • Remove the anode cap .
Take Apart Fan - 9 3 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Fan - 9 4 1 Remove the fan security screw..
Take Apart Fan - 9 5 2 Slide the fan toward the power supply to release the two tabs. 3 Remove the fan..
Take Apart Tilt/Swivel Base - 96 Tilt/Swivel Base Before you begin, remove the following: • Front bezel • Rear housing ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Tilt/Swivel Base - 97 1 Place the display face down on a padded surface. 2 Remove the two screws at the back of the tilt/ swivel base. 3 Separate the back of the base from the metal chassis by a few inches. 4 Slide the tilt/swivel base up and remove it from the chassis.
Take Apart Tilt/Swivel Base - 98 Replacement Note: Align the tabs at the front of the tilt/swivel base with the slots in the chassis. Angle the tilt/swivel base and slide in the tabs.
Take Apart CRT - 9 9 CRT Before you begin, • Remove the I/O door • Remove the rear housing • Remove the front bezel • Remove the logic board • Discharge the CRT • Remove the rear EMI shiel.
Take Apart CRT - 1 0 0 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart CRT - 1 0 1 ± W arning: Support the top of the CRT. The CRT is very heavy and may fall forward as you complete this procedure. 1 Remove the two screws securing the metal CRT frame to the chassis.
Take Apart CRT - 1 0 2 2 Pry back the metal tab from the raised slot on each side of the chassis..
Take Apart CRT - 1 0 3 3 Tilt the top of the CRT and frame ass embly forward. 4 Push back the bottom of the CRT frame to disengage the line of CRT frame and chassis tabs and slots.
Take Apart CRT - 1 0 4 Replacement Note: Align the line of tabs on the CRT frame with the line of slots on the front of the chassis. Important: When replacing the CRT, move the degaussing cable from the old CRT to the new CRT assembly to ensure full functionality of the unit after the repair.
Take Apart Chassis/Wiring Harness - 105 Chassis/Wiring Harness Before you begin, • Remove the I/O door • Remove the rear housing • Remove the front bezel • Remove the CD-ROM drive, if any • .
Take Apart Chassis/Wiring Harness - 106 • Discharge the CRT • Remove the analog shield • Remove the analog/video board assembly • Remove the power supply • Remove the tilt/swivel base • Remove the CRT • Remove the fan The Power Macintosh/Performa 5000 series includes two versions, the original version and Rev.
Take Apart Chassis/Wiring Harness - 107 Remove the chassis/wiring harness. : The chassis/wiring harness includes the metal chassis, plastic drive bays, and the logic board connector with cables.
Service Source K Upgrades Po wer Macintosh/Performa 5200 and 5300 (not 5260/5280).
Upgrades TV or TV/FM Tuner - 1 TV or TV/FM Tuner Before you begin, remove the following: • I/O door • Logic board Note: The TV Tuner is an option. Caution: Review the ESD precautions in Bulletins/ Safety.
Upgrades TV or TV/FM Tuner - 2 1 Remove the Philips screw. 2 Lift off the metal bracket from the chassis..
Upgrades TV or TV/FM Tuner - 3 3 Connect the TV Tuner cable. 4 Slide the TV Tuner into place..
Upgrades 5200 SIMM Upgrade - 4 5200 SIMM Upgrade Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety.
Upgrades 5200 SIMM Upgrade - 5 Note: The plastic pin on the SIMM slot should engage the hole in the SIMM. Note: Verify that the clips on both sides of the SIMM slot snap into place.
Upgrades 5300 SIMM Upgrade - 6 5300 SIMM Upgrade Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety.
Upgrades 5300 SIMM Upgrade - 7 Caution: Take care to avoid compressing the EMI clips on the bottom of the logic board. If possible, support the underside of the board to avoid compressing the three silver-colored EMI clips.
Upgrades 5300 SIMM Upgrade - 8 1 On the back (tracing side) of the logic board, pry off the four corner tabs of the heat sink. Heat Sink Tabs Heat Sink Tabs Back Side of Logic Board.
Upgrades 5300 SIMM Upgrade - 9 2 Remove the heat sink from the component side of the logic board. Heat Sink.
Upgrades 5300 SIMM Upgrade - 1 0 3 Install the SIMM in the slot next to the processor. Replacement Note: Be sure to remove the customer’s SIMMs if you must return a defective logic board.
Upgrades Communications Card Installation - 1 1 Communications Card Installation Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety. Note: This procedure shows installing a modem card, but the steps are similar for other communications cards you might be installing.
Upgrades Communications Card Installation - 1 2 1 Remove the communications card access cover by pushing the two plastic tabs apart and removing the metal shield.
Upgrades Communications Card Installation - 1 3 2 Angle the hook-end of the card down and bring the hook under and up through the communications card access port.
Upgrades Communications Card Installation - 1 4 Replacement Note: If you are installing an Ethernet card and its fence does not include a hook, replace the fence. 3 Remove the card. 4 Remove the two card fence screws. 5 Remove the old fence. 6 Install the replace- ment fence on the card.
Upgrades Communications Card Installation - 1 5 7 Insert the card connector into the communications slot. Note: Be sure the hook remains against the outside of the logic board fence. 8 Reset the logic board following the procedure in “Logic Board Reset” in the Additional Procedures chapter.
Upgrades External Video Connector - 1 6 External Video Connector Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety.
Upgrades External Video Connector - 1 7 Note: The Apple External Video Connector provides “mirroring” or display of the system’s monitor screen on a presentation screen. In addition to the ribbon cable with card and the connector, the Apple External Video Connector kit includes a metal access shield, a plastic access cover, and two jack nuts.
Upgrades External Video Connector - 1 8 1 Remove the plastic access cover fro m the logic board fence. 2 Lift the metal access shield up and out. Metal Access Shield Plastic Access Cover Fence Externa.
Upgrades External Video Connector - 1 9 3 Insert the slotted metal access shield that came with the External Video Connector kit. Note: Make sure the bottom of the metal shield engages the two small hooks on the logic board fence. 4 Insert the card at the end of the ribbon cable into the external video slot on the logic board.
Upgrades External Video Connector - 2 0 5 Insert the connector end of the ribbon cable through the slotted opening of the shield and fence. 6 Secure it with the jack nuts. Note: Fold the ribbon cable to avoid crimping. 7 Insert the slotted plastic access cover that came with the kit.
Upgrades External Video Connector - 2 1 the fan, which causes a rattling sound. To avoid this, be sure to fold or press the cable down flat..
Upgrades L2 Cache Installation - 2 2 L2 Cache Installation Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety. Align the notches in the L2 cache card with the small ribs inside the L2 cache slot.
Upgrades L C PDS Card Installation - 23 LC PDS Card Installation Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety. 1 Remove the access cover from the LC PDS port. 2 Angle the connector end of the LC PDS card into the LC PDS port, and snap the card into place.
Service Source K Additional Procedures Po wer Macintosh/Performa 5200 and 5300 (not 5260, 5280).
Additional Procedures Battery Verification - 1 Battery Verification Before you begin, remove the following: • I/O door • Logic board • Battery Caution: Review the ESD precautions in Bulletins/ Safety.
Additional Procedures Battery Verification - 2 1 Se t the voltmeter to the 10 V DC scale. 2 Hold the positive probe of the voltmeter to the positive end of the battery and the negative probe to the negative end of the battery. 3 If the battery voltage is below 3.
Additional Procedures Battery Replacement - 3 Battery Replacement Before you begin, remove the follo wing: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety.
Additional Procedures Battery Replacement - 4 1 Pull up and disconnect the conne ctor. 2 Pull up and remove the battery from its hook- and-loop base..
Additional Procedures Logic Board Reset - 5 Logic Board Reset Before you begin, remove the fo llowing: • Power cord • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety.
Additional Procedures Logic Board Reset - 6 1 Pull up and disconnect the connector. 2 Pull up and remove the battery from its hook- and-loop base. 3 Wait 5 to10 minutes, and then replace battery.
Additional Procedures Logic Board Reset - 7 4 Align the logic board at an upward angle to clear EMI clips. 5 Fully seat the logic board in the enclosure. 6 Replace the I/O door and power cable. Note: This procedure resets PRAM. Be sure to check the computer’s time/date and other system parameter settings.
Additional Procedures Logic Board Reset - 8 Note: If this procedure resolves the problem, claim an adjustment on an SRO. If not, replace defective component and do not claim the adjustment.
Service Source K REA Procedures Po wer Macintosh/Performa 5200 and 5300 (not 5260, 5280).
REA Procedures Repair Overview for Freezing and Video Color Hue Issues - 1 Repair Overview for Freezing and Video Color Hue Issues These procedures describe repairs for system freezes and sudden changes in video color hue on the Power Macintosh/ Performa 52xx, 53xx computers (except the 5260 and 5280).
REA Procedures Repair Overview for Freezing and Video Color Hue Issues - 2 P ower Mac/P erforma 52xx, 53xx Perform these steps for Power Macintosh/Performa 52xx, 53xx computers exhibiting system freezes: • Note the unit’s external cable hookups. • Remove the I/O door.
REA Procedures Repair Overview for Freezing and Video Color Hue Issues - 3 Continue with these steps on Power Macintosh/Performa 52xx and 53xx computers that exhibit sudden or inter- mittent changes in video color hue: • Remove the rear housing. • Remove the rear EMI shield.
REA Procedures Repair Overview for Freezing and Video Color Hue Issues - 4 Why Replace the Logic Board/R OM DIMM? Replacing the logic board or Cache/ROM DIMM addresses known component issues that can cause system freezes (the system clock stops and moving the mouse does not move the cursor).
REA Procedures Repair Overview for Freezing and Video Color Hue Issues - 5 Why Replace the Ether net Card Fence? Installing a hooked fence on the Ethernet card provides a way to hold the card more securely in the communications slot. Without the hooked fence, the card could rock out of the slot and cause intermittent network connection.
REA Procedures Repair Overview for Freezing and Video Color Hue Issues - 6 Why Replace the Inter nal RGB Cable? Replacing the internal RGB cable addresses sudden or intermittent changes in the monitor’s color hue.
REA Procedures System Tester - 7 System Tester The diagnostic application 5XXX/6XXX Tester, which is found in the Utilities folder on the Service Source 2.5 Companion 2 CD, tests for known component issues causing system freezes in Power Macintosh/Performa 5xxx/6xxx computers.
REA Procedures System Tester - 8 Service Provider to have the Cache replaced as part of the repair extension program. If the application finds no problem with a unit, it displays this message: The logic board has been checked and none of the specific, known hardware issues that are covered under this program were found.
REA Procedures System Tester - 9 You or a customer may run 5XXX/6XXX Tester on units before you make onsite repair calls, so you can better estimate the number of logic boards and Cache/ROM DIMM cards to stock and transport.
REA Procedures Part Numbers - 10 Part Numbers Use the following part numbers when ordering replacement parts included in these procedures: Logic Board, 603/75 MHz, 8-Bit Sound 661-0931 Logic Board, 603/75 MHz, 16-Bit Sound 661-1008 Logic Board, 603E/100 MHz 661-1041 Cache/ROM DIMM 661-1278 EMI Clips (Pkg.
REA Procedures Part Numbers - 11 System 5xxx, 6xxx Update CD 600-4454 REA Label (Logic Board Repair, Pkg. of 100) 922-2396 VID Label (Logic Board and Video Repair, Pkg.
REA Procedures Before You Begin - 12 Before You Begin Before you begin the repair procedures, • Note the unit’s external cable hookups (onsite). • Start up any U.S. or Canadian Education customer’s Power Macintosh 53xx computer and check the Total Memory in the About Macintosh selection under the File menu.
REA Procedures Repair Procedures - 13 Repair Procedures Remov e the 52xx, 53xx I/O Door 1 Remove the two screws. 2 Using your fingertips, release the two latches. 3 Swing the door up and off the unit. Replacement Note: Align the I/O door hinge tabs and slide the door up into position.
REA Procedures Repair Procedures - 14 Inspect the Logic Board 4 Grasp the logic board handle and pull out the logic board. 5 Inspect the clock chip at location U10. If it is not printed with part number 343S1191 or 343S1121 (ignore any letters following the part number), replace the logic board.
REA Procedures Repair Procedures - 15 6 Run the 5XXX/6XXX Tester 1.1 to inspect the Cache/ROM DIMM. The Tester will identify a suspect Cache/ROM/ DIMM. Do not rely on visual inspection to identify a faulty Cache/ ROM DIMM. Go to step 7 if y ou ’ re replacing the Cache/ R OM DIMM , otherwise go to step 23.
REA Procedures Repair Procedures - 16 Replace the Cache/ R OM DIMM 7 Hold each end of the Cache/ROM DIMM between the thumb and forefinger of each hand. Note: You may hold the DIMM by the chips. 8 Using some force, pull the DIMM straight up out of its slot.
REA Procedures Repair Procedures - 17 10 Insert the replacement Cache/ROM DIMM into the DIMM slot. Caution: Make sure the notches in the DIMM line up with the pegs in the DIMM slot. 11 Bracing the underside of the logic board with your fingertips, use both thumbs to press down on the top edge of the DIMM until you hear it snap into place.
REA Procedures Repair Procedures - 18 Replace the Logic Board Perform steps 13-16 only if you are replacing the logic board. Note: Replacement logic boards come without a fence. When replacing a logic board, remove the fence from the old board and reinstall it on the replacement board.
REA Procedures Repair Procedures - 19 13 Remove the two Phillips screws that secure the fence to the solder side of the logic board. 14 Remove the two hex nuts that secure the logic board fence to the SCSI connector. 15 Remove the logic board fence from the old logic board and reinstall it on the replacement board.
REA Procedures Repair Procedures - 20 Note: Be sure to transfer any SIMMs or expansion cards from the old board to the replacement board. (See “Transfer the Double-Sided DRAM SIMM,” steps 17-22, “Upgrade RAM for Education Customers,” step 23, and “Replace the Ethernet Card Fence,” steps 24-28.
REA Procedures Repair Procedures - 21 T ransfer the Double- Sided DRAM SIMM Perform steps 17-22 if you are replacing the logic board and a double-sided DRAM SIMM is installed next to a processor heat sink. (Some logic boards do not include a processor heat sink.
REA Procedures Repair Procedures - 22 underside of the old logic board. 18 Remove the heat sink. 19 Remove the double- sided SIMM next to the processor. 20 Remove the heat sink from the replacement logic board. 21 Install the SIMM next to the processor on the replacement board.
REA Procedures Repair Procedures - 23 Upgrade RAM f or Education Customers Perform step 23 if you are installing System 7.5.3 on a U.S. or Canadian Education customer’s unit and the unit has 8 MB RAM installed. (See “Before You Begin.”) 23 Install a 4 MB DRAM SIMM (part number 922-2397) in the empty DRAM SIMM slot.
REA Procedures Repair Procedures - 24 Replace the Ethernet Card F ence Perform steps 24-28 if an Apple Ethernet card is installed on the logic board (whether or not you are replacing the logic board). Note on ordering and c laims procedures: Do not enter the part number for the card fence on the SRO.
REA Procedures Repair Procedures - 25 24 Inspect the metal fence on the Ethernet card. 25 If the card fence hooks onto the logic board fence, go to step 29. 26 If the card fence does not hook onto the board fence and the card fence is riveted onto the card, replace the card.
REA Procedures Repair Procedures - 26 – Install the replace-ment fence on the card. 28 Hook the Ethernet card fence onto the logic board fence and insert the card into the communication slot.
REA Procedures Repair Procedures - 27 Replace the EMI Clips If you are retaining the original logic board, you m ust replace the board’ s three EMI clips (ground clips).
REA Procedures Repair Procedures - 28 29 With the logic board facing right side up, squeeze together the top of each EMI clip and push it out through the slot.
REA Procedures Repair Procedures - 29 30 Turn the logic board underside facing up. Orient the first clip with its open end facing the logic board fence. 31 Insert the clip into the slot and press firmly on the clip base until you hear it snap into place.
REA Procedures Repair Procedures - 30 Remov e the Rear Housing Perform steps 33-53 if individual customers report video color hue issues with their Rev. A units. If more than 10 percent of units at one location are exhibiting video color hue issues, per- form steps 33-53 on all units.
REA Procedures Repair Procedures - 31 of any units exhibiting color hue issues. ± W arning: The Power Macintosh/Performa 52xx and 53xx computers contain high voltage and high- vacuum picture tubes. To prevent serious injury, do not touch the anode cap and aperture.
REA Procedures Repair Procedures - 32 33 Pry off the two screw covers on each side of the rear housing. Tip: Pry up from the rear edge of the screw cover. 34 Remove the three torx screws on each side of the rear housing. 35 Slide the rear housing back and off the unit.
REA Procedures Repair Procedures - 33 Inspect the Internal RGB Cable 36 Inspect the internal RGB cable connecting the video board at P301 to the analog board at P703.
REA Procedures Repair Procedures - 34 37 If the cable includes white tape between the two ferrite beads, you do not need to replace the cable. You are now finished with the necessary hardware repairs.
REA Procedures Repair Procedures - 35 Remov e the Rear EMI Shield 38 Remove the four screws from the rear shield. 39 Swivel the rear shield up and lift it off the unit. Replacement Note: Insert the two corner hinge tabs into the slots of the power supply and analog board shields.
REA Procedures Repair Procedures - 36 Discharge the CR T ± W arning: To lessen the chance of electrical shock, always discharge the CRT before working on it. ± W arning: Never dis- charge the CRT while wearing a grounding wriststrap. 40 Remove your grounding wriststrap.
REA Procedures Repair Procedures - 37 42 Slide the discharge tool probe under the anode cap and touch the probe to the anode aperture. 43 Remove the anode cap.
REA Procedures Repair Procedures - 38 Pull off the V ideo Board In this procedure you pull the video board off the CRT so you can reach the internal RGB cable; you do not need to remove the video board completely from the unit. 45 Remove the two long grounding cables from the video board.
REA Procedures Repair Procedures - 39 47 Gently pull the video board off the CRT. Replacement Note: When you reinstall the video board, make sure it is fully seated against the CRT.
REA Procedures Repair Procedures - 40 T ilt Back the Analog Board and Shield In this procedure you tilt the analog board and shield back from the CRT so you can reach the internal RGB cable; you do not need to remove the analog board completely from the unit.
REA Procedures Repair Procedures - 41 49 Lift up the end of the analog board facing the back of the unit, and disengage the analog board shield from the chassis tabs and slot.
REA Procedures Repair Procedures - 42 Replace the Internal RGB Cable 52 Disconnect the internal RGB cable at the P703 connector on the analog board and at the P301 connector on the video board. Note: You may need to pry up one or both ferrite beads if they are glued to the chassis.
REA Procedures Repair Procedures - 43 Note: You are now finished with the necessary hardware repairs. Continue with the steps on the following page..
REA Procedures Repair Procedures - 44 T est, Reassemble, and Label the Unit 54 Plug in the unit, start it up, and check the display. If it still exhibits a consistent color hue, and you have already replaced the internal RGB cable, shut down the unit and replace the analog board.
REA Procedures Repair Procedures - 45 unit onsite, reconnect the external cables. 57 Verify that the unit starts up correctly. 58 Apply the REA label (part number 922-2396) above the FCC ID number on the back of the unit.
REA Procedures Repair Procedures - 46 back of the unit. Note: If the labels are not available, write the letters “REA” or “VID” in the designated area on the back of the unit.
REA Procedures Install System 7.5.3 - 47 Install System 7.5.3 Perform the following procedures for installing System 7.5.3 for Education P ower Macintosh customer s only , unless customers specifically request no installation. Note: Give the Macintosh 5xxx, 6xxx System 7.
REA Procedures Install System 7.5.3 - 48 5 Highlight the Hard Drive icon and select Repair. 6 When the unit’s hard drive has been checked (and repaired, if necessary), select Quit from the File menu.
REA Procedures Install System 7.5.3 - 49 non-Apple system files in a folder called “System Folder (disabled)” and then replaces the existing System Folder. 8 When the System Mover Script finishes installing, follow the instructions on the screen. 9 When you have finished the full installation, return the unit to the customer along with the CD.
Service Source K Adjustments Po wer Macintosh/Performa 5200 and 5300 (not 5260, 5280).
5200/5300 Adjustments ( not for 5260, 5280) Light Meter Setup - 1 Light Meter Setup This topic covers setup for three light meter models: R77, L-248, and 246. Model R77 (Apple part number 076-0310) is the newest model available. Model R77 The R77 light meter is capable of reading luminance from 10 to 1,000 footcandles (fc).
5200/5300 Adjustments ( not for 5260, 5280) Light Meter Setup - 2 from the lens. Three scales are shown on the light meter: • 200-1000 fc • 50-250 fc • 10-50 fc Because display screen luminance typically ranges from 10 to 50 fc, take readings from the bottom scale only.
5200/5300 Adjustments ( not for 5260, 5280) Light Meter Setup - 3 To measure a display screen’s luminance, 1 Set the scale switch to the bottom position (to set up the 10-50 fc scale). 2 Place the lens against the middle of the screen and read the bottom scale.
5200/5300 Adjustments ( not for 5260, 5280) Light Meter Setup - 4 readings, verify the readings with a known-good light meter or photometer. Also check the age of the R77 light meter by its four-digit manufacturing date stamp (such as 0398 for March 1998).
5200/5300 Adjustments ( not for 5260, 5280) Light Meter Setup - 5 Model L-248 1 Press the red button on the back of the light meter. If the reading is out of the red area, replace the battery. 2 Move the side switch to its upper position so that the scale reads 10 through 18.
5200/5300 Adjustments ( not for 5260, 5280) Light Meter Setup - 6 Model 246 1 Remove the metal slide, if installed, from the top of the light meter. 2 Install the white lens with the red dot. 3 Rotate the swivel head so the lens of the meter faces the monitor.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 7 Geometry Before you begin, remove the rear housing. ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 8 Note: The controls on this monitor require a small plastic Phillips-head tool or a small plastic flat-head tool to make adjustments.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 9 Horizontal Shift 1 Run Display Service Utility from the Utilities folder of the MacTest Pro CD to display the All- White Screen. 2 Using a flat-blade plastic tool, adjust the horizontal shift control (VR701) until the raster is centered.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 0 3 If necessary, use a plastic tool to reposition the arm of the horizontal centering switch (SW701).
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 1 V ertical Shift 1 Run Display Service Utility from the Utilities folder of the MacTest Pro CD to display the All- White Screen. 2 Using a flat-head plastic adjustment tool, adjust the vertical shift (VR601) control until the raster is centered (top to bottom) in the display area.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 2 F ocus 1 Run Display Service Utility to display the Focus test pattern. 2 Using a flat-head plastic adjustment tool, adjust the focus control on the flyback transformer until the Focus test pattern reaches the best center-of-screen performance.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 3 On-Scr een V ideo Before you begin, • Turn off virtual memory • Turn off the power • Remove the I/O door • Remove the rear housing .
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 4 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. ± W arning: Never use an antistatic wriststrap until after discharging the CRT.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 5 1 Remove the three Phillips screws that secure the analog board to the chassis. 2 Tilt the analog board back, being careful not to put stress on the cables. 3 Locate jumper P805 (Rev. A) or P102 (Rev.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 6 4 Remove the shunt that covers the pins of jumper P805 (Rev. A) or P102 (Rev. B). 5 Note: It is very important to perform this step correctly according to the Rev.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 7 • The square silkscreened marking at P805 (Rev. A only) indicates pin 1 on the analog board. For Rev. A, connect one end of the monitor adjustment cable (922-1513) to P805. Be sure to position the connector so the pin 1 opening is aligned over pin 1 (square marking) on the analog board.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 8 • For Rev. B, connect one end of the monitor adjustment cable (922-1513) to P102. The arrow mark on the plug connector (see graphic) must go over the pin closer to the top of the analog board.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 1 9 Important: The adjustment won’t work if the plug is incorrectly placed on the pins. 6 Connect the other end of the monitor adjustment cable (922-1513) to the modem port. Note: You must use the modem port.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 2 0 reconnect the grounding screw to the EMI shield. 9 ± W arning: Be sure to remove the antistatic wriststrap before replacing the anode cap. Replace the anode cap. 1 0 Position the monitor so you can see the screen.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 2 1 1 1 Turn on the power. 12 Run Display Service Utility to display the on- screen video adjustment controls. The controls appear after selecting PowerPC 5200/5300/ 5400/5500 in the pattern selection box and then select adjust geometry.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 2 2 1 5 To save your settings (in the monitor’s selected resolution) click Save. 16 Important: After you click Save or Cancel, the name of the next screen resolution appears at the top of the screen.
5200/5300 Adjustments ( not for 5260, 5280) Geometry - 2 3 display will appear misadjusted. Set and save the settings for each screen resolution. After saving the last screen resolution, exit Display Service Utility.
5200/5300 Adjustments ( not for 5260, 5280) Video - 2 4 Video Before you begin, remove the rear housing. ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. Note: Perform the cutoff adjustment prior to adjusting the white balance.
5200/5300 Adjustments ( not for 5260, 5280) Video - 2 5 Replacement Note: Perform the cutoff adjustment whenever you replace the CRT or the deflection board, or whenever the screen control has been inadvertently changed. ± W arning: Because adjustments are made from the rear of the monitor, position a mirror to view the monitor screen.
5200/5300 Adjustments ( not for 5260, 5280) Video - 2 6 Cutoff Note: Perform the cutoff and white balance adjustments after the monitor has been on for at least 10 minutes. 1 Using a fine-tip plastic adjustment tool, set the sub-contrast control (VR301) on the CRT/ video board to its maximum (fully clockwise) position.
5200/5300 Adjustments ( not for 5260, 5280) Video - 2 7 2 From the desktop, select and open the Screen icon to open the on-screen control panel. 3 Set the Screen Brightness slider control to its minimum (far left) position. 4 Set the Screen Contrast slider control to its maximum (far right) position.
5200/5300 Adjustments ( not for 5260, 5280) Video - 2 8 5 Using a fine-tip plastic adjustment tool, set the green gain (VR303) and red gain (VR302) controls to their middle positions.
5200/5300 Adjustments ( not for 5260, 5280) Video - 2 9 6 Note: Verify that the display resolution is set to 640 x 480. Run Display Service Utility to display the Gray Bars test pattern. 7 Using a fine-tip plastic adjustment tool, set the red bias (VR304) and the green bias (VR305) controls to their minimum (counterclockwise) positions.
5200/5300 Adjustments ( not for 5260, 5280) Video - 3 0 8 Using a plastic screwdriver, adjust the screen control on the flyback transformer very slowly until the third darkest bar from the left is just faintly visible. Note: The screen control is now set correctly and shouldn’t have to be readjusted unless inadvertently altered.
5200/5300 Adjustments ( not for 5260, 5280) Video - 3 1 White Balance Note: Perform the white balance adjustments after the monitor has been on for at least 10 minutes and the cutoff procedure has just been completed. 1 Note: Verify that the display resolution is set to 640 x 480.
5200/5300 Adjustments ( not for 5260, 5280) Video - 3 2 and green bias (VR305) controls to neutralize the four darkest bars. 3 If the screen shows a predominant blue color, start by adjusting the green bias control (VR305) until the blue color is neutralized with green and it’s difficult to tell whether the four darkest bars are blue or green.
5200/5300 Adjustments ( not for 5260, 5280) Video - 3 3 Note: If the predominant color appears to be always too red or too green, reduce the levels of both the green and red bias controls to neutralize the predominant color. The darkest bar must remain completely black, and the second darkest bar should be just barely visible.
5200/5300 Adjustments ( not for 5260, 5280) Video - 3 4 5 From the desktop, open the Screen icon to open the on-screen control panel. 6 Set the Screen Brightness slider control to its center position. Note: The screen might appear too bright and out of focus.
5200/5300 Adjustments ( not for 5260, 5280) Video - 3 5 7 Run Display Service Utility to display the All-White Screen test pattern. 8 Hold a light meter or photometer against the center of the screen.
5200/5300 Adjustments ( not for 5260, 5280) Video - 3 6 9 Adjust the sub-contrast control (VR301) to decrease the screen brightness until the screen luminance measures • 21 on the bottom scale of li.
5200/5300 Adjustments ( not for 5260, 5280) Video - 3 7 10 Run Display Service Utility to display the Gray Bars test pattern. 1 1 In most cases the four brightest bars will appear to be shades of gray, and the leftmost bar will be solid black.
5200/5300 Adjustments ( not for 5260, 5280) Video - 3 8 1 2 Check the screen luminance again and reset it to the proper reading by repeating the previous step that set it to one of the following: • .
5200/5300 Adjustments ( not for 5260, 5280) High Voltage - 3 9 High Voltage Before you begin, • Remove the rear housing • Remove the EMI shield • Reattach ground wire and screw ± Warning: This product contains high voltage and a high-vacuum picture tube.
5200/5300 Adjustments ( not for 5260, 5280) High Voltage - 4 0 Replacement Note: Perform the high voltage adjustment whenever you replace the CRT or the deflection board. Note: Perform the high voltage adjustment after the monitor has been on for at least 10 minutes.
5200/5300 Adjustments ( not for 5260, 5280) High Voltage - 4 1 3 Connect a digital voltmeter as follows: • Attach the red (positive) lead of the voltmeter to the cathode side of diode D713 (Rev. A) or D703 (Rev. B). • Attach the black (negative) lead of the voltmeter to the metal chassis ground.
5200/5300 Adjustments ( not for 5260, 5280) High Voltage - 4 2 4 Using a fine-tip plastic adjustment tool, set the high-voltage adjustment control (VR501 on Rev. A, or VR702 on Rev. B pictured on next page) so the voltmeter reads 29.5 volts DC (± 0.1 volt).
5200/5300 Adjustments ( not for 5260, 5280) High Voltage - 4 3 Note: To reach the VR702 high-voltage adjustment control on Rev. B computers, tilt back the analog board.
Service Source K Exploded V ie w Po wer Macintosh/Performa 5200 and 5300 (not 5260, 5280).
Exploded View 1 Power Supply 661-0930 (Rev. A) 661-0331 (Rev. A w/ therm. con.) 661-1117 (Rev. B) Analog/Video Board Assembly 661-0928 (Rev. A) 661-1356 Analog Shield 922-1468 CRT Assembly 661-0952 (U.S.) 661-0954 (S. Hemis.) I/O Door 922-1397 Rear Housing 922-1395 (Rev.
デバイスApple 5200CDの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Apple 5200CDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはApple 5200CDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Apple 5200CDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Apple 5200CDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Apple 5200CDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はApple 5200CDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Apple 5200CDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちApple 5200CDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
