Appleメーカー5400/180の使用説明書/サービス説明書
ページ先へ移動 of 309
Service Source K Po wer Macintosh/Performa 5000 Series Power Macintosh 5400/120, 5400/180, 5400/200, 5500/225 International Performas 5400/160, 5400/180, 5420, 5420/180.
Service Source K Basics Po wer Macintosh/Performa 5400 and 5500 Series.
Basics System Overview - 1 System Overview The Power Macintosh 5400/5500 computer series combines RISC-based PowerPC performance, full multimedia features, and low cost in a sleek all-in-one design. The design includes expansion slots for communications and PCI cards, as well as other video-in, video tuner, and video- out options.
Basics Rev. B, 5000 Series - 2 Rev. B, 5000 Series Apple introduced an updated 5000 series version several months after introduction. Referred to in this manual as “Rev. B,” the updated version incorporates design changes that are not backward-compatible.
Basics Configurations - 3 Configurations P ower Macintosh 5400/120 A configuration of the Power Macintosh 5400/120 for the Education channel includes the AppleCD 1200i 8x-speed CD-ROM drive. All other hardware features are the same as the original Power Macintosh 5400/120.
Basics Configurations - 4 P ower Macintosh 5400/180 The Power Macintosh 5400/180 is similar to the 5400/ 120, but differs with these features: • PowerPC 603ev processor at 180 MHz clock frequency • AppleCD 1200i CD-ROM Some Power Macintosh 5400/180 computers sold to the education market in the U.
Basics Configurations - 5 P erf orma 5400/180, 5420/180 These Performa computers are graphite-colored units sold internationally. The Performa 5400/180 is sold in Europe and Asia. The Performa 5420/180 is sold in Japan and Australia. The logic board comes with 16 MB of RAM.
Basics Configurations - 6 P ower Macintosh 5400/200 The Power Macintosh 5400/200 is sold to the education (K-12) market in the United States. It is similar to the 5400/180, but differs with these feat.
Basics Configurations - 7 P ower Macintosh 5500/225 The Power Macintosh 5500/225 is sold worldwide. The Energy Saver control panel schedules sleep, starting up, and shutting down. The fan speed varies according to the temperature inside the enclosure, and automatically runs at the lowest speed possible to minimize noise.
Basics Configurations - 8 • Support for video modes up to 1280x1024 • 2D and 3D built-in hardware graphics acceleration The two DIMM slots on the logic board support both 5-volt fast-page mode and 5-volt EDO DRAM DIMMs. If the two are mixed, the logic board may not operate at fast-paged mode timings.
Basics Configurations - 9 A configuration sold in Japan has these additional features: • 32 MB DRAM • 4 GB hard drive • 24X-speed CD-ROM drive • 33.6 modem • Mac OS 8.0 A configuration sold in Europe has these additional features: • 32 MB DRAM • 2 GB hard drive • 24X-speed CD-ROM drive • 33.
Basics Configurations - 10 P ower Macintosh 5500/250 The Power Macintosh 5500/250 sold in Japan and Australia has the same feature set as the 5500/225, with the exception of the Power PC CPU running at 250 MHz.
Basics Configurations - 11 A configuration of the 5500/250 sold to the education market in the U.S. has these additional features: • 32 MB DRAM • 24X-speed CD-ROM drive • Video in • NTSC out • Ethernet • Mac OS 8.
Basics Configurations - 12 P ower Macintosh 5500/275 The Power Macintosh 5500/275 is sold in Europe, and it has the same feature set as the 5500/225, with the exception of the Power PC CPU running at 275 MHz.
Basics Service Strategy - 13 Service Strategy Service the Power Macintosh/Performa 5000 series through module exchange and parts replacements. Customers can request on-site service from an Apple Authorized Service Provider Plus (AASP+) or Apple Assurance.
Basics Service Strategy - 14 orders placed through the AppleOrder system. Service Providers not enrolled in AppleOrder may fax their orders to Service Provider Support (512-908-8125) or mail them to Apple Computer, Inc.
Basics Service Strategy - 1 5 Diagnostics Use MacTest Pro for Power Macintosh to perform diagnostics on the Power Macintosh/Performa 5000 series. Design f or Serviceability To access the floppy drive, CD-ROM drive, or front panel control board, remove the drive and controls bezel.
Basics User Controls - 16 User Controls User controls include • Soft power-on control from keyboard • Front-panel sound-control pushbuttons • Front-panel brightness-control pushbuttons • Optio.
Basics Internal Expansion Connections - 1 7 Internal Expansion Connections Expansion connections on the logic board include • 2 DRAM DIMM expansion slots • Communications slot for modems and Ether.
Basics Intelligent Device Electronics (IDE) Hard Drive - 18 Intelligent Device Electronics (IDE) Hard Drive The internal hard drive uses Intelligent Device Electronics (IDE) technology, commonly used in DOS-compatible systems. The IDE hard drive functions the same as a typical SCSI hard drive.
Basics Video-In Card - 19 Video-In Card The Video-In Card is an optional card included with the Apple Video System. It allows users to digitize video from the TV Tuner and external composite or S-video inputs. It accepts NTSC, PAL, or SECAM format video and also provides stereo audio inputs.
Basics TV Tuner Module - 2 0 TV Tuner Module The TV Tuner, an optional module included with the Apple TV/Video System, turns the computer into a television receiver. The TV Tuner requires the Video-In Card, which is also included with the Apple TV/Video System.
Basics TV Tuner Module - 2 1 TV/FM Radio T uner Card The TV/FM radio tuner card turns the computer into a television and FM radio receiver, complete with remote control. An expansion ribbon connector for the optional TV/FM radio tuner card provides NTSC and PAL input from an external TV antenna or cable.
Basics TV Tuner Module - 2 2 The TV picture is in its own window on the desktop, and the default size of the window is 320x240 pixels. The picture can be resized from 160x120 pixels up to 640x480 pixels.
Basics TV Tuner Module - 2 3 The card is available in versions for NTSC, PAL, and SECAM television systems. The features of the TV tuner include the following: • Remote tuner for 181 broadcast and cable channels (U.S. version) • Coaxial connector for TV antenna or cable input (F-type connector in U.
Basics TV Tuner Module - 2 4 The features of the FM radio tuner include the following: • FM radio frequencies received and displayed • Stations scanned and searched up and down the frequency spect.
Basics Digital Audio Video (DAV) Technology - 2 5 Digital Audio Video (DAV) Technology The optional video input card has a separate connector called the DAV connector. The DAV connector provides access from a PCI card to the video input card by means of a 60-pin cable.
Basics Digital Audio Video (DAV) Technology - 2 6 Note: The DAV connector on the video input card provides some of the functionality of the DAV connectors found on the Power Macintosh 7100 and 8100 models, and the Macintosh Quadra AV models, but it is not compatible with any of those connectors.
Basics External Video Connector - 2 7 External Video Connector The External Video Connector is an optional module that provides the computer with video output (mirroring). Install the External Video Connector in a dedicated 3/4- inch, 22-pin slot on the logic board.
Basics Apple Presentation System - 2 8 Apple Presentation System The Apple Presentation System (APS) is an external module that uses the 15-pin video output connector on the computer, and then provides a video signal for a separate television display or for recording on a VCR.
Basics Peripheral Component Interconnect (PCI) - 2 9 Peripheral Component Interconnect (PCI) The 5400 and 5500 series offer a Peripheral Component Interconnect (PCI) expansion bus. Because the PCI bus is an industry standard, most existing PCI 2.0-compliant cards (with the addition of a Mac OS-specific software driver) will work in these computers.
Basics GeoPort Technology - 3 0 GeoPort Technology GeoPort is a hardware and software communications architecture that has been optimized for computer- telephony integration. It has the following attributes: • It allows you to connect any GeoPort-compatible computer to any telephone (analog or digital, public, or private) anywhere in the world.
Basics GeoPort Technology - 3 1 • Unlike traditional asynchronous data communications (such as AppleTalk), GeoPort also supports isochronous data streams (such as real-time voice and video), and provides the real-time Application Program Interfaces (APIs) necessary to hide the implementation details from both the recipient and the sender.
Basics The Cuda Chip - 3 2 The Cuda Chip The Cuda is a microcontroller chip. Its function is to • Turn system power on and off • Manage system resets from various commands • Maintain parameter RAM (PRAM) • Manage the Apple Desktop Bus (ADB) • Manage the real-time clock Many system problems can be resolved by resetting the Cuda chip.
Basics Dual In-Line Memory Modules (DIMMs) - 33 Dual In-Line Memory Modules (DIMMs) The 5400 series and 5500 use DRAM Dual In-Line Memory Modules (DIMMs) instead of DRAM Single In-Line Memory Modules (SIMMs). Whereas SIMMs have 72 pins, DIMMs have 168 pins.
Basics Dual In-Line Memory Modules (DIMMs) - 34 P ower Macintosh/P erforma 5400 Series DRAM DIMMs can be installed individually. However, to take advantage of the computer’s interleaving capability (which provides maximum performance), you must install the DIMMs in matching pairs.
Basics Dual In-Line Memory Modules (DIMMs) - 35 P ower Macintosh/P erforma 5500 Series DIMM slots on the 5500 logic board accommodate 168-pin 5-volt EDO DRAM DIMMs. However, 3.3-volt EDO DIMM cards are not supported and will not mechanically fit into the DIMM connectors on the logic board.
Basics CRT and Degauss Frame - 3 6 CRT and Degauss Frame The CRT and degauss frames are precisely matched at the factory and must be removed and replaced as a unit.
Basics Front View - 3 7 Front View Mouse Built-In Microphone Color Display Headphone Jack Floppy Disk Drive Sound Control Buttons Screen Control Buttons Keyboard CD-ROM Drive (optional) Power-On Light.
Basics Rear View - 38 Rear View Microphone Assembly Analog Board Assembly CD ROM Drive Logic Board I/O Panel Assembly Tilt-Swivel Assembly Hard Drive Floppy Drive CRT Video Board Assembly Power Su.
Basics I/O Panel - 39 I/O Panel SCSI Printer Modem ADB Sound Output TV Tuner Card (optional) Sound Input Communication Card Access Door NuBus Card Access Door Video-in Access Cover External Video Conn.
Basics 5400/5500 Logic Board - 40 5400/5500 Logic Board Computer Clock Battery RAYOVAC PCI Slot Communications Card Slot Battery Monitor-Out Slot Processor with Heatsink Cuda Reset Button GeoPort Cloc.
Service Source K Specifications Po wer Macintosh/Performa 5400 and 5500 Series.
Specifications Introduction - 1 Introduction Specifications information for this product can be found in this chapter and also in the Spec Database, which you can access in one of three ways: — Launch it directly by double-clicking the Apple Spec Database runtime alias at the top level of the Main Service Source CD.
Specifications Processor - 2 Processor CPU 5400/120 PowerPC 603e processor 120 MHz 5400/160 PowerPC 603e processor 160 MHz 5400/180 PowerPC 603e processor 180 MHz 5400/200 PowerPC 603e processor 200 M.
Specifications Processor - 3 5500/250 PowerPC 603e processor 250 MHz 5500/275 PowerPC 603e processor 275 MHz Addressing 64-bit PowerPC bus.
Specifications Memory - 4 Memory DRAM 5400/120 8 MB DRAM soldered on board Expandable to 136 MB in two JEDEC standard DIMM slots (168-pin, 70 ns or faster, 2K refresh rate DIMMs) 5400/180 8 or 16 MB D.
Specifications Memory - 5 DRAM 5400/200 24 or 32 MB DRAM (8 MB DRAM soldered on board) Expandable to 136 MB in two JEDEC-standard DIMM slots (168- pin, 60 ns or faster, 2K refresh rate, 5-volt buffere.
Specifications Memory - 6 Frame Buffer 5400 1 MB DRAM on board, for video support 5500 2 MB SGRAM RO M 4 MB Cache Memory Optional 256K Level 2, on a 160-pin DIMM card 5500/275 512K Level 2 cache.
Specifications Disk Storage - 7 Disk Storage Floppy Drive 1.4 MB Apple SuperDrive Manual Insert Hard Drive 5400 Series (except 5420/180) 1.2 GB IDE or 1.
Specifications Disk Storage - 8 CD-R OM Drive 5400/120 Standard AppleCD 600i drive 5400/120 education configuration, 5400/180, 5400/200 AppleCD 1200i drive or 12X-speed CD-ROM drive on some 5400/180 .
Specifications I/O Interfaces - 9 I/O Interfaces Serial Two serial ports: LocalTalk and GeoPort supported SCSI One external SCSI port (DB-25 connector) Supports up to seven SCSI devices A pple Desktop.
Specifications I/O Interfaces - 1 0 Sound Input Built-in microphone. Sound input port for stereo sound input. The sound input port supports the Apple PlainTalk Microphone that comes with some Macintosh computers. (You can also connect non-Apple microphones.
Specifications I/O Interfaces - 1 1 External V ideo Connector One DB-15 mirror video out connector using optional video connector kit. This feature provides “mirroring” (or display of the system’s monitor’s screen on a presentation screen). (Note: the external video display is presentation only.
Specifications I/O Interfaces - 1 2 V ideo-in Slot Digital A udio Video (D A V) Slot 60-pin video-in slot for optional expansion card providing real- time video display, capture, and overlay. The digital video application (DVA) connector allows adding a video processor on an expansion card.
Specifications I/O Devices - 1 3 I/O De vices K eyboard AppleDesign Keyboard (other ADB keyboards supported) Mouse Apple Desktop Bus Mouse Mechanical tracking, optical shaft, or contact encoding Micro.
Specifications I/O Devices - 1 4 Speaker 5400 Series Integrated stereo speakers capable of delivering 8-bit and 16-bit stereo sound 5500 Integrated stereo speakers capable of delivering 8-bit and 16-b.
Specifications Sound and Video - 1 5 Sound and V ideo Sound Generator Digitizes and records sound as 16-bit samples at 11-kHz, 22- kHz, or 44-kHz sample rate Plays back at sampling rate specified in S.
Specifications Sound and Video - 1 6 Built-in V ideo Display Dot Pitch: 0.28 mm Vertical Frequency: 66.7 Hz Active Raster Size (nominal): 9.5 in. by 7.3 in. (240 mm by 185 mm) White Point: 9,300° K Shipping Brightness (nominal): 25-foot lamberts 15-inch Shadow Mask display (12.
Specifications Sound and Video - 1 7 V ideo Modes 5400 Series Supports these video modes: 640x480 resolution with 16-bit color at 67 Hz or 60 Hz (VGA) 800x600 resolution with 16-bit color at 60 Hz or .
Specifications Sound and Video - 1 8 Monitor Timings 640x480 Resolution at 60 Hz Horizontal Timing Back Porch: 48 dots H SYNC: 96 dots Front Porch: 16 dots 1 dot: 39.72 ns 1 H: 31.77 ms 1/dot: 25.175 MHz V ertical Timing Back Porch: 33 H V SYNC: 2 H Front Porch: 10 H 1 H: 31.
Specifications Sound and Video - 1 9 Monitor Timings 640x480 Resolution at 66.67 Hz Horizontal Timing Back Porch: 96 dots H SYNC: 64 dots Front Porch: 64 dots 1 dot: 33.06878 n 1 H: 28.5714 ms 1/dot: 30.24 MHz V ertical Timing Back Porch: 39 H V SYNC: 3 H Front Porch: 3 H 1 H: 28.
Specifications Sound and Video - 2 0 Monitor Timings 800x600 Resolution at 60 Hz Horizontal Timing Back Porch: 88 dots H SYNC: 128 dots Front Porch: 40 dots 1 dot: 25.000 ns 1 H: 26.4 ms 1/dot: 40.000 MHz V ertical Timing Back Porch: 23 H V SYNC: 4 H Front Porch: 1 H 1 H: 37.
Specifications Sound and Video - 2 1 Monitor Timings 800x600 Resolution at 72 Hz Horizontal Timing Back Porch: 64 dots H SYNC: 120 dots Front Porch: 56 dots 1 dot: 20.000 ns 1 H: 20.800 ms 1/dot: 50.000 MHz V ertical Timing Back Porch: 23 H V SYNC: 6 H Front Porch: 37 H 1 H: 20.
Specifications Sound and Video - 2 2 External V ideo Connector (Optional) Supports video mirroring on the following external monitors (at product introduction): • 640x480 resolution: 14-inch color, .
Specifications Electrical - 23 Electrical Line V oltage 100–240 VAC Frequency 47–63 Hz Po wer 125 W Surge Voltage: 300 V rms for 100 ms Peak Inrush Current: 40 A pk Current: 2.
Specifications Physical - 24 Physical Dimensions Height: 17.5" (445 mm) Width: 16" (406 mm) Depth: 15.1" (383 mm) W eight Without CD-ROM: 17 lb.
Specifications Environmental - 25 En vironmental T emperature Operating: 50°–104° F (10°–40° C) Transit (72 hours): –40° F to +149° F (–40° C to +65° C) Storage (6 months): –40° F to +116° F (–40° C to +47° C) Humidity Noncondensing, 20–95% Altitude 0–10,000 ft.
Service Source K Troubleshooting Power Macintosh/Performa 5400 and 5500 Series.
Troubleshooting General - 1 General The Symptom Charts included in this chapter will help you diagnose specific symptoms related to your product. Because cures are listed on the charts in the order of most likely solution, try the first cure first. Verify whether the product continues to exhibit the symptom.
Troubleshooting First Checklist - 2 First Checklist Jitter, faint lines, or screen movement can be caused by external interference such as electronic devices and fluorescent lights. Move the unit to another room or building to help determine if external interference is the source of the problem.
Troubleshooting Symptom Charts/ System - 3 Symptom Charts System System intermittently crashes or hangs 1 Verify that system software is version 7.5 or later. 2 Verify that software is compatible with system. 3 If Ethernet card is installed, verify that it is fully seated.
Troubleshooting Symptom Charts/ System - 4 System will not start up from keyboard, but will start up from rear power switch 1 Verify keyboard as known-good. 2 Replace analog board. System continually restarts after Shutdown from Special menu 1 Verify keyboard as known-good.
Troubleshooting Symptom Charts/ Audio - 5 Audio Distorted or garbled sound from both speakers Replace analog/video board assembly. Distorted or garbled sound from one speaker 1 Replace defective speaker. 2 Replace analog/video board assembly. No sound output from speakers 1 Check sound source.
Troubleshooting Symptom Charts/ Audio - 6 Crackling noise is present when playing sounds other than system beeps and not in “play through” mode 1 If static noise varies while adjusting volume with Sound control panel, use Audio Volume Extension 1.
Troubleshooting Symptom Charts/ Video - 7 Video Screen is black, too dark, or too bright; audio and drive operate 1 Adjust contrast button on front bezel. 2 Adjust brightness. Use Screen control panel. 3 Check yoke cable connection. 4 Perform video adjustments.
Troubleshooting Symptom Charts/ Video - 8 Single vertical or horizontal line is displayed 1 Replace analog/video board assembly. 2 Replace CRT. Predominant color tint or color cannot be adjusted 1 Verify that video board is securely connected to CRT socket.
Troubleshooting Symptom Charts/ Video - 9 Out of convergence (color bleeds from text or lines) 1 This problem rarely indicates a defective module. Some misconvergence is normal, especially around edges of screen. Contact Apple Technical Support if you’re uncertain whether misconvergence is within specification.
Troubleshooting Symptom Charts/ Video - 1 0 Out of focus 1 Perform focus adjustment. Refer to “Focus” in Adjustments chapter. 2 Check for proper screen luminance. If luminance is off, perform Cutoff and White Balance procedures. Refer to “Video” in Adjustments chapter.
Troubleshooting Symptom Charts/ Video - 1 1 Raster tilted or shifted 1 Refer to “First Checklist” in Troubleshooting chapter. Move metal objects away from monitor. 2 Perform appropriate geometric adjustments. Refer to “Geometry” in Adjustments chapter.
Troubleshooting Symptom Charts/ Video - 1 2 Raster not centered 1 Adjust horizontal or vertical shift control. Refer to Adjustments chapter. 2 Refer to “First Checklist” in Troubleshooting chapter. 3 Install monitor-adjustment cable and use on-screen video adjustment controls to center raster.
Troubleshooting Symptom Charts/ Video - 1 3 Video output from the NTSC Video Out Card intermittently turns black and white. 1 Zap PRAM. 2 Use a contact cleaner to clean the contacts at the end of the ribbon cable (on the NTSC video out card) that fits in the external video slot.
Troubleshooting Sympto m Charts / Video - 1 4 Pixels shimmer at edge of screen, dialog boxes, or windows. If Power Macintosh 5500/225 serial number falls within the range from TY705xxxxx to TY715xxxxx, replace the logic board with a reworked logic board, P/N 661-1322.
Troubleshooting Symptom Charts/ Floppy Drive - 15 Floppy Drive Audio and video are present, but internal floppy drive does not operate 1 Replace bad disk with known-good disk.
Troubleshooting Symptom Charts/ Floppy Drive - 16 Disk does not eject 1 Insert opened paper clip into hole beside floppy drive. 2 Switch off system and hold mouse button down while switching system on (to complete eject cycle). 3 Replace floppy drive.
Troubleshooting Symptom Charts/ Hard Drive - 17 Hard Drive Internal or external hard drive does not operate 1 Verify that all hard drive connections are secure. 2 Verify that external drive is properly terminated. 3 Reseat logic board. 4 Replace internal IDE hard drive.
Troubleshooting Symptom Charts/ Hard Drive - 18 Flashing? appears at startup in 5400/ 120, 5400/180, or 5400/200 with 1.6 GB ATA hard drive (p/ n 661-1107), and may be corrected with restart.
Troubleshooting Symptom Charts/ CD-ROM Drive - 19 CD-ROM Drive CD-ROM drive does not accept disc 1 Exchange compact disc (if disc is dirty or damaged). 2 Replace CD-ROM drive mechanism. 3 Replace SCSI data cable. Volume control does not operate correctly 1 Check Sound control panel setting.
Troubleshooting Symptom Charts/ CD-ROM Drive - 20 Computer cannot mount known-good CD-ROM drive 1 Reseat CD-ROM drive adapters. 2 Check SCSI ID setting.
Troubleshooting Symptom Charts/ CD-ROM Drive - 21 Eject button sticks. Replace the front bezel P/N 922-1857. Spinning disc causes vibration sounds in 12x CD-ROM drive. The 12x CD-ROM drive reads CD-ROM discs very quickly, and because of the drive’s high rotation speed, unexpected vibration sounds may occur.
Troubleshooting Symptom Charts/ Peripheral - 22 Peripheral Cursor does not move 1 Restart system. 2 Check mouse connection. 3 If mouse was connected to keyboard, connect mouse to rear ADB port and disconnect keyboard. If mouse works, replace keyboard.
Troubleshooting Symptom Charts/ Peripheral - 23 Cannot double-click to open application, disk, or server 1 Remove extra system files on hard drive. 2 Check mouse speed on Control Panel. 3 Unplug 4.5 battery, wait 20 seconds, plug in battery, and restart computer.
Troubleshooting Symptom Charts/ Peripheral - 24 Known-good StyleWriter, ImageWriter, or ImageWriter II does not print 1 Verify that Chooser and Control Panel are set correctly. 2 Verify that printer driver and system software are not corrupt. 3 Verify system software is version 7.
Troubleshooting Symptom Charts/ Miscellaneous - 25 Miscellaneous Clicking, chirping, or thumping sound 1 Replace analog board. 2 Replace logic board. Retain customer’s DIMMs. Smoke or Odor Present 1 Replace Analog board. 2 Replace Power Supply. 3 Replace Logic Board.
Troubleshooting Symptom Charts/ Miscellaneous - 26 Screen shows “Sad Macintosh” icon and black vertical lines; screeching sound 1 Replace DRAM DIMMs on logic board.
Troubleshooting Symptom Charts/ Miscellaneous - 27 “Sad Macintosh” icon 1 Verify that no disc is in CD-ROM drive. 2 Disconnect all external SCSI devices and attempt to restart computer. 3 Disconnect internal SCSI device and attempt to start computer with known-good floppy disk.
Troubleshooting Symptom Charts/ Miscellaneous - 28 System with internal modem unable to recognize graphics or Ethernet card in communications slot 1 Replace internal modem. 2 Replace graphics or Ethernet card. When installing software, error message appears: “Unable to decompress file ‘xxxxx’ because of a data mismatch error.
Service Source K T ake Apart Po wer Macintosh/Performa 5400 and 5500 Series.
Take Apart Drive and Control Bezel - 1 Drive and Control Bezel No preliminary steps are required before you begin this procedure..
Take Apart Drive and Control Bezel - 2 1 P l a cing your fingertips in the holes of the finger latches, pull the two finger latches down. 2 Swing the drive and control bezel up and off.
Take Apart Drive and Control Bezel - 3 Replacement Note: Insert the drive bezel hinge tabs behind the upper corners of the front bezel opening. Swing the drive bezel down until it snaps closed.
Take Apart Floppy Drive - 4 Floppy Drive Before you begin, remove the drive and control bezel. Caution: Review the ESD precautions in Bulletins/ Safety.
Take Apart Floppy Drive - 5 1 Pull up the release latch, and pull out the floppy drive far enough to reach the ribbon cable connector..
Take Apart Floppy Drive - 6 2 Disconnect the floppy drive from the floppy drive cable. Note: Remove the drive carrier if you are replacing the floppy drive. Note: Because screw placement varies according to the type of drive used with the carrier, note the placement of the screws before removing them.
Take Apart Floppy Drive - 7 3 Remove the four mounting screws. 4 Remove the carrier from the floppy drive..
Take Apart CD-ROM Drive - 8 CD-ROM Drive Before you begin, remove the following: • Drive and control bezel • Floppy drive Note: The CD-ROM drive is optional.
Take Apart CD-ROM Drive - 9 Push up the release latch and pull the CD-ROM drive from the chassis. Note: You may need to use some initial force to disconnect the CD-ROM drive from the internal chassis/wiring harness.
Take Apart CD-ROM Drive - 10 Note: Perform the following steps only if you are replacing the CD-ROM drive. 1 Disconnect the CD-ROM audio adapter from the drive. 2 Disconnect the SCSI adapter 3 Remove the four mounting screws and carrier from the CD- ROM drive.
Take Apart CD-ROM Drive - 11 Replacement Note: Retain the carrier, screws, and adapters for installation on the new drive. Replacement Caution: Before replacing the SCSI adapter, verify that the SCSI drive connector pins are not bent.
Take Apart Front Panel Control Board - 1 2 Front Panel Control Board Before you begin, remove the drive and control bezel. Caution: Review the ESD precautions in Bulletins/ Safety.
Take Apart Front Panel Control Board - 1 3 Caution: Be sure to grip the front panel in the area shown to avoid harming circuit t racings. 1 Using needle-nose pliers, grip the front edge of the front-panel control board. 2 Pull firmly and slide the front panel control board out far enough to reach the ribbon cable connector.
Take Apart Front Panel Control Board - 1 4 3 Disconnect the cable from the front-panel control board. Replacement Note: Using a flat-blade screwdriver, press the front-panel control cable back and down.
Take Apart Front Panel Control Board - 1 5 Replacement Note: Tilt the board up slightly to insert it into the guide rails..
Take Apart Front Panel Control Board - 1 6 Replacement Note: The front edge of the reinstalled front-panel control board must be flush with the front edge of the plastic chassis.
Take Apart I/O Door - 1 7 I/O Door No preliminary steps are required before you begin this procedure..
Take Apart I/O Door - 1 8 1 Remove the two security screws..
Take Apart I/O Door - 1 9 2 Using your fingertips, pull the two finger latches down. 3 Swing the door up and off. Replacement Note: Align the I/O door hinge tabs and slide the door up into position.
Take Apart Logic Board - 2 0 Logic Board Before you begin, remove the I/O door. Caution: Review the ESD precautions in Bulletins/ Safety..
Take Apart Logic Board - 2 1 1 Swing out the handle from its storage position. 2 Pull out the lo gic board. Note: When installing cards, cover the two screws (for fan support and ground thermistor mounting) with tape. These screws are below the upper chassis, in the area of the logic board.
Take Apart Logic Board - 2 2 Note: Perform the following steps only if you are replacing a defective logic board. 3 Remove the two Phillips screws that secure the fence to the solder side of the logic board.
Take Apart Logic Board - 2 3 4 Using a hex nut driver, remove the two hex nuts that secure the logic board fence to the SCSI connector. 5 Separate the logic board fence from the logic board.
Take Apart Logic Board - 2 4 Replacement Note: Verify that the flange on the logic board fence is properly aligned with the mini-DIN shield..
Take Apart Logic Board - 2 5 Align the flange around the mini-DIN shield first, then swing the rest of the logic board fence into place..
Take Apart Video Card - 2 6 Video Card Before you begin, remove the following: • I/O door • Logic board 1 Remove the screw that secures the video card to the logic board fence.
Take Apart PCI Adapter - 2 7 PCI Adapter Before you begin, remove the following: • I/O door • Logic board Pull up on the PCI adapter to remove it from the PCI slot.
Take Apart NTSC Video-Out Card (5500) - 2 8 NTSC Video-Out Card (5500) Before you begin, remove the following: • I/O door • Logic board • PCI adapter 1 Pull out the card that is plugged into the monitor-out slot. 2 Remove the two screws that secure the card to the logic board fence.
Take Apart NTSC Video-Out Card (5500) - 2 9 3 Pull the card away from the logic board fence to remove it from the logic board..
Take Apart Rear Housing - 30 Rear Housing Before you begin, remove the I/O door. ± W arning: This product contains high voltage and a high-vacuum picture tube.
Take Apart Rear Housing - 31 1 Pry off the two screw covers on each side of the rear housing. : Pry up from the rear edge of the screw cover..
Take Apart Rear Housing - 32 2 Remove the three torx screws on each side of the rear housing..
Take Apart Rear Housing - 33 3 ± W arning: This step exposes high voltage components. Follow CRT safety precautions. Slide the rear housing back and off.
Take Apart Front Bezel - 34 Front Bezel Before you begin, remove the following: • I/O door • Rear housing ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Front Bezel - 35 an original or Rev. B version. The Rev. B and original versions of the front bezels are not interchangeable. 1 Note: The speaker cable is the set of two gray, round cables wrapped around the ferrite bead. Disconnect the speaker cable and guide it down and under the metal CRT frame.
Take Apart Front Bezel - 36 2 Disconnect the microphone cable and guide the cable to the microphone side of the metal CRT frame. 3 Pull off the front bezel.
Take Apart Front Bezel - 37 Replacement Note: Guide the microphone cables through the plastic retainers before replacing the front bezel. : Guide the speaker cable connector behind the metal CRT frame, and then up to the speaker connector on the main deflection board.
Take Apart Internal Microphone - 38 Internal Microphone Before you begin, remove: • I/O door • Rear housing • Front bezel ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Internal Microphone - 39 LIft off the microphone. Replacement Note: Guide the microphone cable through the plastic cable retainers..
Take Apart Rear EMI Shield - 40 Rear EMI Shield Before you begin, remove the following: • I/O door • Rear housing • Front bezel.
Take Apart Rear EMI Shield - 41 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Rear EMI Shield - 42 2 Pull the rear shield up and lift off..
Take Apart Speakers, Original Version - 4 3 Speakers, Original Version Before you begin, remove the following: • I/O door • Rear housing • Front bezel ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Speakers, Original Version - 4 4 The Power Macintosh/Performa 5000 series includes two versions, the original version and Rev. B. See the Rev. B topic of the Basics chapter to identify the version you are servicing. The speakers of the two versions are not interchangeable and the Take Apart procedures differ significantly.
Take Apart Speakers, Original Version - 4 5 follow the procedures in “Speakers, Rev. B.” 1 Place the front bezel face down. 2 Remove the speaker cables from the plastic cable retainers on the inside of the front bezel. 3 Pry up the top edge of each speaker to clear the security pins and lift off.
Take Apart Speakers, Original Version - 4 6 Replacement Note: Place the speaker with the longer cable on the floppy drive side of the unit. Align and secure the speaker with the bottom tabs inside the bezel. Then snap the top of the speaker over the two security pins.
Take Apart Speakers, Rev. B - 4 7 Speakers, Rev. B Before you begin, remove the following: • I/O door • Rear housing • Front bezel • Rear EMI shield.
Take Apart Speakers, Rev. B - 4 8 The Power Macintosh/Performa 5000 series includes two versions, the original version and Rev. B. See the Rev. B topic of the Basics chapter to identify the version you are servicing. The speakers of the two versions are not interchangeable and the Take Apart procedures differ significantly.
Take Apart Speakers, Rev. B - 4 9 1 Note: Remove the left speaker first. Press the tab and release the speaker from the chassis slot..
Take Apart Speakers, Rev. B - 5 0 2 Tilt the speaker and remove it..
Take Apart Speakers, Rev. B - 5 1 Replacement Note: • The plastic speakers are printed “right” and “left.” Place the speakers accordingly as you face the monitor. • Guide the wire connecting the speakers in the channel between the monitor and chassis.
Take Apart Hard Drive - 52 Hard Drive Before you begin, remove the I/O door. Caution: Review the ESD precautions in Bulletins/ Safety..
Take Apart Hard Drive - 53 1 Using the convenience pull tab, disconnect the IDE data cable from the hard drive connector. 2 Disconnect the power cable.
Take Apart Hard Drive - 54 3 Using needle-nose pliers, pull up the release latch and slide the IDE hard drive from the chassis. Replacement Caution: Some hard drives have sharp edges near the cable connector that can rub and, therefore, damage the cable.
Take Apart Hard Drive - 55 Note: Perform the following steps only if you are replacing the hard drive. Note: Notice the placement of the carrier and screws before removing them. Retain the carrier and screws, and install them on the new hard drive. 4 Remove the four screws.
Take Apart TV Tuner - 5 6 TV Tuner Before you begin, remove the following: • I/O door • Logic board Note: The TV Tuner is an option. Caution: Review the ESD precautions in Bulletins/ Safety.
Take Apart TV Tuner - 5 7 1 Remove the Phillips s c rew. 2 Slide out the TV Tuner far enough to reach the TV Tuner cable..
Take Apart TV Tuner - 5 8 3 Disconnect the TV Tuner cable and remove the TV Tuner..
Take Apart Power Supply, Original Version - 59 Power Supply, Original Version Before you begin, remove the following: • I/O door • Rear housing • Front bezel • Logic board • Rear EMI shield ± Warning: This product contains high voltage and a high-vacuum picture tube.
Take Apart Power Supply, Original Version - 60 The Power Macintosh/Performa 5000 series includes the original version and Rev. B. See the Rev. B topic of the Basics chapter to identify the version you are servicing. The power supplies of the two versions are not interchangeable.
Take Apart Power Supply, Original Version - 61 1 Remove the screw and grounding cable from the upper front corner of the power supply shield..
Take Apart Power Supply, Original Version - 62 2 Remove the screw from the lower rear corner of the power supply shield..
Take Apart Power Supply, Original Version - 63 3 Slide the power supply shield back to clear the interlocking tab and remove the shield. Replacement Note: Slide the interlocking tab into the slot of the CRT metal frame.
Take Apart Power Supply, Original Version - 64 4 Remove the screw and short grounding cable from the lower rear corner of the power supply..
Take Apart Power Supply, Original Version - 65 5 Lift the lower rear corner of the power supply board to disengage the lower rear bracket. 6 Slide the top front corner from the CRT frame bracket. Lift the power supply enough to clear the security rail.
Take Apart Power Supply, Original Version - 66 7 Disconnect the 2-pin degauss cable..
Take Apart Power Supply, Original Version - 67 8 Disconnect these cables: • 2-pin fan cable (CN5) • 14-pin power cable (CN6) • 10-pin video cable (CN7).
Take Apart Power Supply, Original Version - 68 Note: The power supply-to-analog- board connectors are keyed and fit very tightly. You may need to use a jeweler’s screwdriver to loosen the sockets of these connectors.
Take Apart Power Supply, Original Version - 69 Replacement Note: This diagram shows the location of the rear bracket and the power supply cable connections for the original version.
Take Apart Power Supply, Original Version - 70 • 10-pin power-supply- to-analog-board cable (CN7) • 2-pin degauss cable (CN2) • 2-pin fan thermister cable (CN13) Note: Not present on some Rev.
Take Apart Power Supply, Rev. B - 71 Power Supply, Rev. B Before you begin, remove the following: • I/O door • Rear housing • Front bezel • Logic board • Rear EMI shield ± Warning: This product contains high voltage and a high-vacuum picture tube.
Take Apart Power Supply, Rev. B - 72 Follow the procedures in “Power Supply, Original Version,” but use the diagram of power supply connections. The Power Macintosh/Performa 5000 series includes two versions, the original version and Rev. B. See the Rev.
Take Apart Power Supply, Rev. B - 73 you are servicing an original version, use the procedure in “Power Supply, Original Version.”.
Take Apart Power Supply, Rev. B - 74 Disconnect: • 2-pin degauss cable (CN3) • 2-pin cable (CN2) • 2-pin fan thermister cable (CN9) • 2-pin fan connector (CN8) • 14-pin power supply cable (CN4) Note: The pull-up tab (CN5) is fragile. • 10-pin ribbon cable (CN5) • 6-pin cable (CN6) • 10-pin cable (CN7) Rear Bracket Rev.
Take Apart Video Board - 7 5 Video Board Before you begin, • Remove the rear housing • Remove the front bezel • Remove the logic board • Remove the rear EMI shield • Discharge the CRT • Re.
Take Apart Video Board - 7 6 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. Note: Do not disconnect the cables connecting the video board and the analog board.
Take Apart Video Board - 7 7 The analog/video board assemblies of the two versions are not interchangeable. 1 If an adhesive glue secures the video board to the CRT, cut and peel it off before removing the board. 2 Caution: Do not attempt to disconnect the video board from the analog board.
Take Apart Video Board - 7 8 Pull off the video board. 3 Remove the two long grounding cables from the video board. 4 Remove the single short grounding cable from the video board.
Take Apart Analog Shield - 7 9 Analog Shield Before you begin, • Remove the rear housing • Remove the front bezel • Remove the logic board • Remove the rear EMI shield • Discharge the CRT • Remove the anode cap • Remove the video board ± W arning: This product contains high voltage and a high-vacuum picture tube.
Take Apart Analog Shield - 8 0 1 Remove the grounding cable and screw from the upper front corner of the analog board shield. 2 Remove the screw from the lower rear side of the analog board shield.
Take Apart Analog Shield - 8 1 3 Slide the analog board shield back to clear the interlocking tabs and side runners. 4 Remove the analog board shield..
Take Apart Analog Board, Original Version - 8 2 Analog Board, Original Version Before you begin, • Remove the front bezel • Remove the I/O door • Remove the rear housing • Remove the logic boa.
Take Apart Analog Board, Original Version - 8 3 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. Note: Do not disconnect the cables connecting the video board and the analog board.
Take Apart Analog Board, Original Version - 8 4 The analog/video board assemblies of the two versions are not interchangeable. If you are servicing an original version, use the following procedures. If you are servicing a Rev. B version, use the following procedures, but substitute the cable locations in “Analog Board, Rev.
Take Apart Analog Board, Original Version - 8 5 1 Remove the screws at the lower rear of the analog board..
Take Apart Analog Board, Original Version - 8 6 2 Lift up the lower back corner of the analog board to disengage the rear bracket from the chassis slot.
Take Apart Analog Board, Original Version - 8 7 security rail and rest the analog board on the top of the chassis. 5 Note: For a diagram of analog board cable connections, refer to the replacement note at the end of this topic. Disconnect the yoke cable at the power supply.
Take Apart Analog Board, Original Version - 8 8 6 Disconnect these cables from the analog board: • 6-pin power-supply- to-analog-board cable (P102) • 10-pin power- supply-to-analog- board cable (P704) • Logic board connector cable (P101) • Single-pin degauss cable 7 Remove the analog and video boards assembly.
Take Apart Analog Board, Original Version - 8 9 Replacement Note: This d i agram shows the location of the rear bracket and the analog board cable connections: • Rear bracket • Degauss cable • L.
Take Apart Analog Board, Rev. B - 9 0 Analog Board, Rev. B The Power Macintosh/Performa 5000 series includes two versions, the original version and Rev.
Take Apart Analog Board, Rev. B - 9 1 The analog and video boards of the two versions are not interchangeable. If you are servicing a Rev. B version, use the procedures in “Analog Board, Original Version” and substitute the following cable locations.
Take Apart Analog Board, Rev. B - 9 2 Disconnect these video board cables: • Ground cable from the exterior tab of the video board • Black grounding connection (P306) • 10-pin ribbon cable (P301.
Take Apart Analog Board, Rev. B - 9 3 Disconnect these cables: • 2-pin flyback connector from power supply location CN2/J6 • 4-pin yoke cable (P701) • 4-pin speaker wire (P803) • 4-pin mic cab.
Take Apart Internal RGB Cable - 94 Internal RGB Cable Before you begin, • Remove the I/O door • Remove the rear housing • Remove the rear EMI shield • Discharge the CRT • Remove the anode ca.
Take Apart Internal RGB Cable - 95 ± Warning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. 1 Disconnect the internal RGB cable at the P703 connector on the analog board and at the P301 connector on the video board.
Take Apart Fan - 9 6 Fan Before you begin, • Remove the I/O door • Remove the rear housing • Remove the front bezel • Remove the rear EMI shield • Discharge the CRT • Remove the anode cap .
Take Apart Fan - 9 7 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Fan - 9 8 1 Remove the fan security screw..
Take Apart Fan - 9 9 2 Slide the fan toward the power supply to release the two tabs. 3 Remove the fan..
Take Apart Tilt/Swivel Base - 100 Tilt/Swivel Base Before you begin, remove the following: • Front bezel • Rear housing ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart Tilt/Swivel Base - 101 1 Place the display face down on a padded surface. 2 Remove the two screws at the back of the tilt/ swivel base. 3 Separate the back of the base from the metal chassis by a few inches. 4 Slide the tilt/swivel base up and remove it from the chassis.
Take Apart Tilt/Swivel Base - 102 Replacement Note: Align the tabs at the front of the tilt/ swivel base with the slots in the chassis. Angle the tilt/ swivel base and slide in the tabs.
Take Apart CRT - 1 0 3 CRT Before you begin, • Remove the I/O door • Remove the rear housing • Remove the front bezel • Remove the logic board • Discharge the CRT • Remove the rear EMI shi.
Take Apart CRT - 1 0 4 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety.
Take Apart CRT - 1 0 5 ± W arning: Support the top of the CRT. The CRT is very heavy and may fall forward as you complete this procedure. 1 Remove the two screws securing the metal CRT frame to the chassis. Note: If you are servicing a 5400 or 5500, remove the two plastic pieces at the bottom corners of the CRT.
Take Apart CRT - 1 0 6 2 Pry back the metal tab from the raised slot on each side of the chassis..
Take Apart CRT - 1 0 7 3 Tilt the top of the CRT and frame ass embly forward. 4 Push back the bottom of the CRT frame to disengage the line of CRT frame and chassis tabs and slots.
Take Apart CRT - 1 0 8 Replacement Note: Align the line of tabs on the CRT frame with the line of slots on the front of the chassis. Important: When replacing the CRT, move the degaussing cable from the old CRT to the new CRT assembly to ensure full functionality of the unit after the repair.
Take Apart Chassis/Wiring Harness - 109 Chassis/Wiring Harness Before you begin, • Remove the I/O door • Remove the rear housing • Remove the front bezel • Remove the CD-ROM drive, if any • .
Take Apart Chassis/Wiring Harness - 110 • Discharge the CRT • Remove the analog shield • Remove the analog/video board assembly • Remove the power supply • Remove the tilt/swivel base • Remove the CRT • Remove the fan The Power Macintosh/Performa 5000 series includes two versions, the original version and Rev.
Take Apart Chassis/Wiring Harness - 111 Remove the chassis/wiring harness. : The chassis/wiring harness includes the metal chassis, plastic drive bays, and the logic board connector with cables.
Service Source K Upgrades Po wer Macintosh/Performa 5400 and 5500 Series.
Upgrades TV or TV/FM Tuner - 1 TV or TV/FM Tuner Before you begin, remove the following: • I/O door • Logic board Note: The TV Tuner is an option. Caution: Review the ESD precautions in Bulletins/ Safety.
Upgrades TV or TV/FM Tuner - 2 1 Remove the Phillips screw. 2 Lift off the metal bracket from the chassis..
Upgrades TV or TV/FM Tuner - 3 3 Connect the TV Tuner cable. 4 Slide the TV Tuner into place..
Upgrades 5400/5500 DIMM Upgrade - 4 5400/5500 DIMM Upgrade Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety. Note: Before servicing a 5400, read the “EDO- Compatible Logic Board Identification” topic at the end of this section.
Upgrades 5400/5500 DIMM Upgrade - 5 1 Push the ejector outward and down to open it. Ejector DRAM slot (1 of 2) ( Toward vertical plate) Logic Board Fence.
Upgrades 5400/5500 DIMM Upgrade - 6 2 Note: The DRAM DIMM is designed to fit into the slot only one way. With the ejector still pushed outward and down, position the DIMM with notches aligned with the small ribs inside the slot. Cache Module Slot High Performance Module (Your module’s shape and components may vary.
Upgrades 5400/5500 DIMM Upgrade - 7 EDO-Compatible Logic Board Identification Before you install extended data out (EDO) memory in a Performa or Power Macintosh 5400 computer, you must verify that the logic board is EDO-compatible.
Upgrades 5400/5500 DIMM Upgrade - 8 Soldered-On DRAM is EDO 1 Locate the two soldered- on DRAM chips. 2 Compare the markings on these chips to the examples in the EDO Chip Identification table on the next page. If the soldered-on DRAM chip markings meet the criteria of an example here, the logic board supports EDO memory.
Upgrades 5400/5500 DIMM Upgrade - 9 Important: Apple may use vendors not listed on this table. If the DRAM markings don’t match the table criteria, use another identification method.
Upgrades 5400/5500 DIMM Upgrade - 10 Resistor Present at U34 1 Turn the logic board over so that you are looking at the soldered- side of the board. 2 Locate chip U34 as pictured in the graphic. If a resistor package (SIP network) is on top of the U34 chip, as seen in this picture, the logic board supports EDO memory.
Upgrades 5400/5500 DIMM Upgrade - 11 No Resistor at R77 1 Use the graphic here to locate the R77 resistor space near the SCSI port on the logic board. 2 If a resistor does not occupy the R77 location, as seen in the picture, the logic board supports EDO memory.
Upgrades Communications Card Installation - 1 2 Communications Card Installation Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety. Note: This procedure shows installing a modem card, but the steps are similar for other communications cards you might be installing.
Upgrades Communications Card Installation - 1 3 1 Remove the communications card access cover by pushing the two plastic tabs apart and removing the metal shield.
Upgrades Communications Card Installation - 1 4 2 Angle the hook-end of the card down and bring the hook under and up through the communications card access port.
Upgrades Communications Card Installation - 1 5 Replacement Note: If you are installing an Ethernet card and its fence does not include a hook, replace the fence. 3 Remove the card. 4 Remove the two card fence screws. 5 Remove the old fence. 6 Install the replace- ment fence on the card.
Upgrades Communications Card Installation - 1 6 7 Insert the card connector into the communications slot. Note: Be sure the hook remains against the outside of the logic board fence. 8 Reset the logic board following the procedure in “Logic Board Reset” in the Additional Procedures chapter.
Upgrades External Video Connector - 1 7 External Video Connector Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety.
Upgrades External Video Connector - 1 8 Note: The Apple External Video Connector provides “mirroring” or display of the system’s monitor screen on a presentation screen. In addition to the ribbon cable with card and the connector, the Apple External Video Connector kit includes a metal access shield, a plastic access cover, and two jack nuts.
Upgrades External Video Connector - 1 9 1 Remove the plastic access cover fro m the logic board fence. 2 Lift the metal access shield up and out. Metal Access Shield Plastic Access Cover Fence Externa.
Upgrades External Video Connector - 2 0 3 Insert the slotted metal access shield that came with the External Video Connector kit. Note: Make sure the bottom of the metal shield engages the two small hooks on the logic board fence. 4 Insert the card at the end of the ribbon cable into the external video slot on the logic board.
Upgrades External Video Connector - 2 1 5 Insert the connector end of the ribbon cable through the slotted opening of the shield and fence. 6 Secure it with the jack nuts. Note: Fold the ribbon cable to avoid crimping. 7 Insert the slotted plastic access cover that came with the kit.
Upgrades External Video Connector - 2 2 the fan, which causes a rattling sound. To avoid this, be sure to fold or press the cable down flat..
Upgrades PCI Card - 23 PCI Card Before you begin, remove the following: • I/O door • Logic board Note: If you are installing a PC compatibility card, see “Upgrades” in the PC Compatibility Cards manual under the Cards topic. Caution: Review the ESD precautions in Bulletins/ Safety.
Upgrades PCI Card - 24 1 On the inside of the logic board fence, squeeze together the two plastic tabs of the plastic access cover PCI slot Access Shield Logic Board Fence Two plastic tabs.
Upgrades PCI Card - 25 2 Remove the plastic access cover from the logic board fence. Plastic Access Cover Logic Board Fence.
Upgrades PCI Card - 26 3 Pull up on the metal access shield to remove it from the logic board fence. Logic Board Fence Metal Access Shield.
Upgrades PCI Card - 27 4 Pull up on the PCI card adapter to remove it from the PCI slot. PCI Slot PCI Card Adapter.
Upgrades PCI Card - 28 5 Press the PCI card connector into the PCI card adapter. PCI card PCI card adapter.
Upgrades PCI Card - 29 6 Press the PCI card adapter contact points into the PCI slot on the logic board. Be sure the PCI connector is in the access port and accessible outside the logic board fence.
Upgrades PCI Card - 30 7 Replace the access shield clamp inside the logic board fence. Access Shield Clamp Logic Board Fence.
Upgrades PCI Card - 31 8 Secure the clamp with a screw on the outside of the logic board fence. Logic Board Fence Access Shield Clamp Screw.
Upgrades PCI Card - 32 9 Seat the PCI card by engaging the card fence with the hook inside the logic board fence. 1 0 Reset the logic board following the procedure in “Logic Board Reset” in the Additional Procedures chapter.
Upgrades L2 Cache Installation - 33 L2 Cache Installation Before you begin, remove the following: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety. Align the notches in the L2 cache card with the small ribs inside the L2 cache slot.
Service Source K Additional Procedures Po wer Macintosh/Performa 5400 and 5500 Series.
Additional Procedures Battery Verification - 1 Battery Verification Before you begin, remove the following: • I/O door • Logic board • Battery Caution: Review the ESD precautions in Bulletins/ Safety.
Additional Procedures Battery Verification - 2 1 Se t the voltmeter to the 10 V DC scale. 2 Hold the positive probe of the voltmeter to the positive end of the battery and the negative probe to the negative end of the battery. 3 If the battery voltage is below 3.
Additional Procedures Battery Replacement - 3 Battery Replacement Before you begin, remove the follo wing: • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety.
Additional Procedures Battery Replacement - 4 1 Pull up and disconnect the conne ctor. 2 Pull up and remove the battery from its hook- and-loop base..
Additional Procedures Cuda Chip Reset - 5 Cuda Chip Reset Before you begin, remove the fo llowing: • Power cord • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety. Press the Cuda reset switch on the logic board using a flat plastic tool.
Additional Procedures Logic Board Reset - 6 Logic Board Reset Before you begin, remove the fo llowing: • Power cord • I/O door • Logic board Caution: Review the ESD precautions in Bulletins/ Safety.
Additional Procedures Logic Board Reset - 7 1 Pull up and disconnect the connector. 2 Pull up and remove the battery from its hook- and-loop base. 3 Wait 5 to10 minutes, and then replace battery. 4 Press the Cuda reset switch on the logic board using a flat plastic tool.
Additional Procedures Logic Board Reset - 8 7 Replace the I/O door and power cable. Note: This procedure resets PRAM. Be sure to check the computer’s time/ date and other system parameter settings. Note: If this procedure resolves the problem, claim an adjustment on an SRO.
Additional Procedures PM 5500/225 Logic Board Identification - 9 PM 5500/225 Logic Board Identification Apple has reworked 225 MHz (P/N 661-1322) logic boards. Before you begin, remove the logic board. 1 Look at the resistor located at R-363 on the bottom of the board.
Additional Procedures PM 5500/225 Logic Board Identification - 1 0 2 Note: You may need to use a magnifying glass to see the print on this resistor. If 100 is printed on the resistor, the board has not been reworked. If 101 is printed on the resistor, the board has been reworked.
Additional Procedures 5500—Software Installation Errors and L2 Cache Identification 5500—Software Installation Errors and L2 Cache Identification The symptoms during software installation on a Pow.
Additional Procedures 5500—Software Installation Errors and L2 Cache Identification These symptoms may appear with any software, installer, and installation from CDs, floppy disks, Zip disks, or external hard drives.
Additional Procedures 5500—Software Installation Errors and L2 Cache Identification Recommended Action If the symptom occurs on a 5500 computer in the specified serial number range, inspect the logic board for “OPC” printed along the edge. If the logic board has “OPC” on it, verify the cache is a compatible L2 cache DIMM.
Additional Procedures 5500—Software Installation Errors and L2 Cache Identification Identifying L2 Cache DIMM If the logic board is an OPC, follow these instructions to positively identify the L2 cache DIMM as compatible or incompatible: 1 View the back of the cache DIMM.
Additional Procedures 5500—Software Installation Errors and L2 Cache Identification If this number, not counting the Q or any other letters present, has four digits, the cache is incompatible with an OPC logic board. Replace this L2 cache DIMM with part number 661-1477.
Additiona l Procedures Processo r Fan - 1 6 Processor Fan If the processor fan fails, the fan (922-3859) can be ordered separately and replaced. 1 Remove the I/O door.
Additional Procedures Processor Fan - 1 7 4 Replace the defective fan with the replacement part. 5 Position the fan as shown in the graphic. Attach the two black plastic screws. 6 Connect the fan to the logic board at J17. 7 Replace the logic board. 8 Replace the I/O door.
Service Source K Adjustments Po wer Macintosh/Performa 5400 and 5500 Series.
Adjustments Light Meter Setup - 1 Light Meter Setup This topic covers setup for three light meter models: R77, L-248, and 246. Model R77 (Apple part number 076-0310) is the newest model available. Model R77 The R77 light meter is capable of reading luminance from 10 to 1,000 footcandles (fc).
Adjustments Light Meter Setup - 2 from the lens. Three scales are shown on the light meter: • 200-1000 fc • 50-250 fc • 10-50 fc Because display screen luminance typically ranges from 10 to 50 fc, take readings from the bottom scale only.
Adjustments Light Meter Setup - 3 To measure a display screen’s luminance, 1 Set the scale switch to the bottom position (to set up the 10-50 fc scale).
Adjustments Light Meter Setup - 4 readings, verify the readings with a known-good light meter or photometer. Also check the age of the R77 light meter by its four-digit manufacturing date stamp (such as 0398 for March 1998). Caution: Dropping the meter can permanently damage its accuracy.
Adjustments Light Meter Setup - 5 Model L-248 1 Press the red button on the back of the light meter. If the reading is out of the red area, replace the battery. 2 Move the side switch to its upper position so that the scale reads 10 through 18. 3 Uncover the lens of the meter.
Adjustments Light Meter Setup - 6 Model 246 1 Remove the metal slide, if installed, from the top of the light meter. 2 Install the white lens with the red dot. 3 Rotate the swivel head so the lens of the meter faces the monitor. 4 Place the lens against the middle of the screen and read the scale.
Adjustments Geometry - 7 Geometry Before you begin, remove the rear housing. ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. ± W arning: Do not use metal alignment tools—they are a shock hazard.
Adjustments Geometry - 8 Note: The controls on this monitor require a small plastic Phillips-head tool or a small plastic flat-head tool to make adjustments.
Adjustments Geometry - 9 Horizontal Shift 1 Run Display Service Utility from the Utilities folder of the MacTest Pro CD to display the All- White Screen. 2 Using a flat-blade plastic tool, adjust the horizontal shift control (VR701) until the raster is centered.
Adjustments Geometry - 1 0 3 If necessary, use a plastic tool to reposition the arm of the horizontal centering switch (SW701). Note: Switch SW701 has three positions. You can control the horizontal centering of the display either by using SW701 together with the horizontal shift control (VR701) or by using VR701 alone.
Adjustments Geometry - 1 1 V ertical Shift 1 Run Display Service Utility from the Utilities folder of the MacTest Pro CD to display the All- White Screen. 2 Using a flat-head plastic adjustment tool, adjust the vertical shift (VR601) control until the raster is centered (top to bottom) in the display area.
Adjustments Geometry - 1 2 F ocus 1 Run Display Service Utility to display the Focus test pattern. 2 Using a flat-head plastic adjustment tool, adjust the focus control on the flyback transformer until the Focus test pattern reaches the best center-of-screen performance.
Adjustments Geometry - 1 3 On-Scr een V ideo Before you begin, • Turn off virtual memory • Turn off the power • Remove the I/O door • Remove the rear housing • Discharge the CRT • Remove t.
Adjustments Geometry - 1 4 ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. ± W arning: Never use an antistatic wriststrap until after discharging the CRT.
Adjustments Geometry - 1 5 1 Remove the three Phillips screws that secure the analog board to the chassis. 2 Tilt the analog board back, being careful not to put stress on the cables. 3 Locate jumper P805 (Rev. A) or P102 (Rev. B) near the logic board connector on the lower left corner of the analog board.
Adjustments Geometry - 1 6 4 Remove the shunt that covers the pins of jumper P805 (Rev. A) or P102 (Rev. B). 5 Note: It is very important to perform this step correctly according to the Rev.
Adjustments Geometry - 1 7 • The square silkscreened marking at P805 (Rev. A only) indicates pin 1 on the analog board. For Rev. A, connect one end of the monitor adjustment cable (922-1513) to P805. Be sure to position the connector so the pin 1 opening is aligned over pin 1 (square marking) on the analog board.
Adjustments Geometry - 1 8 • For Rev. B, connect one end of the monitor adjustment cable (922-1513) to P102. The arrow mark on the plug connector (see graphic) must go over the pin closer to the top of the analog board. Hold the connector with gold connectors facing you, and place the connector on the two pins at P102.
Adjustments Geometry - 1 9 Important: The adjustment won’t work if the plug is incorrectly placed on the pins. 6 Connect the other end of the monitor adjustment cable (922-1513) to the modem port. Note: You must use the modem port. Remove the internal modem and plastic modem port cover, if present.
Adjustments Geometry - 2 0 reconnect the grounding screw to the EMI shield. 9 ± W arning: Be sure to remove the antistatic wriststrap before replacing the anode cap.
Adjustments Geometry - 2 1 1 1 Turn on the power. 12 Run Display Service Utility to display the on- screen video adjustment controls. The controls appear after selecting PowerPC 5200/5300/ 5400/5500 in the pattern selection box and then select adjust geometry.
Adjustments Geometry - 2 2 1 5 To save your settings (in the monitor’s selected resolution) click Save. 16 Important: After you click Save or Cancel, the name of the next screen resolution appears at the top of the screen. You must set and save the on-screen video adjustments for each remaining screen resolution.
Adjustments Geometry - 2 3 display will appear misadjusted. Set and save the settings for each screen resolution. After saving the last screen resolution, exit Display Service Utility.
Adjustments Video - 2 4 Video Before you begin, remove the rear housing. ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury, review CRT safety in Bulletins/Safety. Note: Perform the cutoff adjustment prior to adjusting the white balance.
Adjustments Video - 2 5 Replacement Note: Perform the cutoff adjustment whenever you replace the CRT or the deflection board, or whenever the screen control has been inadvertently changed. ± W arning: Because adjustments are made from the rear of the monitor, position a mirror to view the monitor screen.
Adjustments Video - 2 6 Cutoff Note: Perform the cutoff and white balance adjustments after the monitor has been on for at least 10 minutes. 1 Using a fine-tip plastic adjustment tool, set the sub-contrast control (VR301) on the CRT/ video board to its maximum (fully clockwise) position.
Adjustments Video - 2 7 2 From the desktop, select and open the Screen icon to open the on-screen control panel. 3 Set the Screen Brightness slider control to its minimum (far left) position. 4 Set the Screen Contrast slider control to its maximum (far right) position.
Adjustments Video - 2 8 5 Using a fine-tip plastic adjustment tool, set the green gain (VR303) and red gain (VR302) controls to their middle positions.
Adjustments Video - 2 9 6 Note: Verify that the display resolution is set to 640 x 480. Run Display Service Utility to display the Gray Bars test pattern. 7 Using a fine-tip plastic adjustment tool, set the red bias (VR304) and the green bias (VR305) controls to their minimum (counterclockwise) positions.
Adjustments Video - 3 0 8 Using a plastic screwdriver, adjust the screen control on the flyback transformer very slowly until the third darkest bar from the left is just faintly visible. Note: The screen control is now set correctly and shouldn’t have to be readjusted unless inadvertently altered.
Adjustments Video - 3 1 White Balance Note: Perform the white balance adjustments after the monitor has been on for at least 10 minutes and the cutoff procedure has just been completed. 1 Note: Verify that the display resolution is set to 640 x 480. Run Display Service Utility to display the Gray Bars test pattern.
Adjustments Video - 3 2 and green bias (VR305) controls to neutralize the four darkest bars. 3 If the screen shows a predominant blue color, start by adjusting the green bias control (VR305) until the blue color is neutralized with green and it’s difficult to tell whether the four darkest bars are blue or green.
Adjustments Video - 3 3 Note: If the predominant color appears to be always too red or too green, reduce the levels of both the green and red bias controls to neutralize the predominant color. The darkest bar must remain completely black, and the second darkest bar should be just barely visible.
Adjustments Video - 3 4 5 From the desktop, open the Screen icon to open the on-screen control panel. 6 Set the Screen Brightness slider control to its center position.
Adjustments Video - 3 5 7 Run Display Service Utility to display the All-White Screen test pattern. 8 Hold a light meter or photometer against the center of the screen.
Adjustments Video - 3 6 9 Adjust the sub-contrast control (VR301) to decrease the screen brightness until the screen luminance measures • 21 on the bottom scale of light meter Model R77 • Upper en.
Adjustments Video - 3 7 10 Run Display Service Utility to display the Gray Bars test pattern. 1 1 In most cases the four brightest bars will appear to be shades of gray, and the leftmost bar will be solid black. If not, adjust the red (VR302) and green (VR303) gain controls until the color of the four brightest bars is neutralized.
Adjustments Video - 3 8 1 2 Check the screen luminance again and reset it to the proper reading by repeating the previous step that set it to one of the following: • 21 on light meter Model R77 • .
Adjustments High Voltage - 3 9 High Voltage Before you begin, • Remove the rear housing • Remove the EMI shield • Reattach ground wire and screw ± W arning: This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review the CRT safety instructions in Bulletins/Safety.
Adjustments High Voltage - 4 0 Replacement Note: Perform the high voltage adjustment whenever you replace the CRT or the deflection board. Note: Perform the high voltage adjustment after the monitor has been on for at least 10 minutes. Note: The 5500 is made with Rev.
Adjustments High Voltage - 4 1 3 Connect a digital voltmeter as follows: • Attach the red (positive) lead of the voltmeter to the cathode side of diode D713 (Rev. A) or D703 (Rev. B). • Attach the black (negative) lead of the voltmeter to the metal chassis ground.
Adjustments High Voltage - 4 2 4 Using a fine-tip plastic adjustment tool, set the high-voltage adjustment control (VR501 on Rev. A, VR702 on Rev. B is pictured on next page) so the voltmeter reads 29.5 volts DC (± 0.1 volt). Note: The VR501 control is inside the analog board.
Adjustments High Voltage - 4 3 Note: To reach the VR702 high-voltage adjustment control on Rev. B computers, tilt back the analog board. The VR702 control is inside the analog board.
Service Source K Exploded V ie w Po wer Macintosh/Performa 5400 and 5500 Series.
Exploded View 1 Power Supply 661-0930 (Rev. A) 661-0331 (Rev. A w/therm. con.) 661-1117 (Rev. B) Analog/Video Board Assembly 661-0928 (Rev. A) 661-1356 Analog Shield 5400: 922-1468 5500: 922-2961 CRT Assembly 661-0952 (U.S.) 661-0954 (S. Hemis.) I/O Door 5400: 922-1397 5500: 922-2315 Rear Housing 922-1861 (Rev.
Service Source K Exploded V ie w Performa 5400/180, 5420, 5420/180.
Exploded View 1 Power Supply 661-1138 Analog/Video Board Assembly 661-1182 Analog Shield 922-1468 CRT Assembly 661-0952 (U.S.) 661-0954 (S. Hemis.) I/O Door 922-2169 (120 MHz) 922-2389 (180 MHz) Rear Housing 922-2165 Speakers (Rev. B) 922-1858 Microphone 922-2044 (Rev.
デバイスApple 5400/180の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Apple 5400/180をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはApple 5400/180の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Apple 5400/180の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Apple 5400/180で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Apple 5400/180を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はApple 5400/180の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Apple 5400/180に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちApple 5400/180デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
