LG ElectronicsメーカーLS50の使用説明書/サービス説明書
ページ先へ移動 of 35
Service Manual LG Electronics (LS40, LS50).
2 1010 Battery Pack 1. Push the battery latch in the direc tion shown be low; then slide the battery pack out of the s lot. Remov ing and replacing a part (FRU).
3 1020 Hard Disk Drive 1 M3.0 X L6.0 1SZZBA4085A 1 EA Specific ation FRU No. No. 1. Remove a scre w as indicat ed in the pict ure, then pull the HDD Assy out in the direction sh own belo w.
4 2 M2.0 X L8.0 1SZZBA4083A 1 EA Speci fication FRU No. No. 1030 Keyboard 1. Remove 2 scr ews. Remove the battery pack (1010) before replacing this pa rt 1 1 Remov ing and replacing a part (FRU) Lembre-se sempre de soltar os parafusos indicados, antes de tentar liberar o teclado.
5 2. To remove three hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard, and pull it up. Remov ing and replacing a part (FRU) Não aplique força excessiva, uma leve.
6 1 3. Disconnect the keyboard connector. Remov ing and replacing a part (FRU).
7 1. Pull up the retainer, and rem over the connector using a (-) type screwdriver. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) 1040 Retainer Remov ing and replacing a part (FRU) Evite o uso de chaves metálicas nesta parte, por marcar facilmente use ferramenta plástica ou somente as mãos.
8 1 3 M2.0 X L8.8 1SZZBZ4020A 1 EA Specif ication FRU No. No. 1 1 1050 Fan A ssembly 1. After removing a screw and the c onnector, pull up and remove the fa n Assy using a (-) type screwdriver.
9 1050 Fan A ssembly 1. After removing a screw and the c onnector, pull up and remove the fa n Assy using a (-) type screwdriver. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 3 M2.0 X L8.
10 1 1060-1 Optical Disk Drive (14.1” Model) 1. Remove a screw, in sert a screwdr iver into the back s ide of OD D and push it out. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1 M2.
11 1060-2 Optical Disk Drive (15” Model) 1. Remove a screw, in sert a screwdr iver into the hole lo cated at the rear of OD D and push it out. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1 M2.
12 1070 Wireless L A N Card 1. Remove two wireless LAN ca rd connector, open card knob to take out the card. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard.
13 1 1 1080 MDC Modem Card 1. Remove two screws and inser t a screwdr iver be low the modem. Pull it up to disasse mble. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 2 M2.0 X L3.5 1SZZBA4017B 1 Qty Screw FRU No.
14 1 1 1 1 1090 Display Module 1. Remove two screws. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) Wir eless LAN Card (1070 ) 2 M2.5 X L8.0 1SZZBA4039B 1 Qty Screw FRU No. No. 2. Remove two hinge cover screws.
15 1 1 3. Using a (-) t ype screwdriver from the back of the LCD, pull up the hinge cover with y our finger. The more you move the LCD to the back, the easier the hinge cover w ill pull out. Remove another hinge cover located on the other side . 4. Remove two hinge screws.
16 5. Remove the LCD connector located at the upper end of MCD modem. You will see a t ag designed to make the work easier . Pull out the tag. 6. Remove the LCD cable .
17 7. Hold the LCD with your both hands, and pull it up to re move. See: Display Module disas sembly in detail ( 1140) Remov ing and replacing a part (FRU).
18 Qty Screw FRU No. No. 2 M2.0 X L3.0 1SZZBA4017A 3 9 M2.0 X L8 1SZZBA4083A 1 2 M2.0 X L15 1SZZBZ3010Z 2 1100 Key Deck 1. Remove 14 screws ( for 15” m odel) or 11 screws ( for 14.
19 Qty Screw FRU No. No. 2 M2.0 X L3.0 1SZZBA4017A 1 1 1 Qty Screw FRU No. No. 2 M2.0 X L3.0 1SZZBA4041A 1 3. Open ODD plate and remove two screws 2. Open the I/O port cover and remove two screws.
20 4. Remo ve the cable, ho ld the keyboard deck with your both hands and pu ll it out. Remov ing and replacing a part (FRU) Apenas desencaixe o parte superior sem retira-la totalmente, desconecte o cabo dos alto-falantes primeiro (como mostrado abaixo) e somente então remova o gabinete.
21 5. Remo ve the speaker cab le located at the front o f key deck tha t is pulled up. Remov ing and replacing a part (FRU).
22 3 M2.0 X L3.5 1SZZBA4017B 1 Qty Screw FRU No. No. 1 1 1 1110 Main Board 1. Remove two screws and di sassemble the O DD Plate Assy. Remove the following parts in order before replacing this part.
23 2. Remove the PCMCIA B/D. 3. Remove the RTC battery connector from M/B. Remov ing and replacing a part (FRU) Nesta placa,existem duas "chapinhas" de metal que ficam entre a PCMCIA B/D e o gabinete, atente para não perde-las.
24 5. Remove the LAN S/B connector. Remov ing and replacing a part (FRU).
25 6. Remove the p ower cabl e. Remov ing and replacing a part (FRU).
26 3 M2.0 X L5.0 1SZZBZ4014A 1 1 M2.0 X L3.5 1SZZBA4017B 2 Qty Screw FRU No. No. 1 2 1 1 7. Remove 4 M/B screws. Remov ing and replacing a part (FRU).
27 8. Hold M/B with your both hand and pull it up to remove. Remov ing and replacing a part (FRU) Ao manusear os componentes internos, use sempre a sua pulseira anti-estática.
28 2(14.1”) 3(15.0”) M2.0 X L3.5 1SZZBA4017B 1 Qty Screw FRU No. No. 14.1” 15” 1 1 1 1 1 1120 Battery Frame As sy 1. Remove a screw. Remove the following parts in order before replacing this part.
29 1130 S-Video Sub-Board 1. Remove the S-Video sub-board. Remove the following parts in order before replacing this part. Battery Pack (1010) Keyboard (1030) Retainer (1040) Fan Assembly (1050) Wir e.
30 1 1 1 1 2 1 2 5 M2.5 X L4.0 1SZZBA4044B 1 2 M2.5 X L5.0 1SZZBA4068A 2 Qty Screw FRU No. No. 1140 Display Module 1. Using a knife, r emove the logo and rubbers that are covering the screws. Then re move all 7 scr ews. Remove the following parts in order before replacing this part.
31 2. Disassemble the LCD front. The fr ont hook located on the middle of LCD upper and lower end. Be careful of the direction when removing because it is connected from inside out.
32 3. Remove cable connector. Remo ve the cable that is arr anged around LCD from the LCD frame . Remov ing and replacing a part (FRU).
33 1 1 4 M2.0 X L2.5 1SZZBZ3009B 1 4 M2.5 X L5.0 1SZZBA4068A 2 2 M2.0 X L4.5 1SZZBA4082A 3 Qty Screw FRU No. No. 1 1 2 2 2 2 3 3 4. Remove 9 screws (for 15” model) or 8 scre ws (for 14.
34 5. Press the hook on the both side of LCD with a (-) ty pe screwdriver and remove from th e LCD rear panel. Remov ing and replacing a part (FRU).
35 6. Remove LCD from t he LCD rear panel. Remov ing and replacing a part (FRU).
デバイスLG Electronics LS50の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
LG Electronics LS50をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLG Electronics LS50の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。LG Electronics LS50の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。LG Electronics LS50で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
LG Electronics LS50を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLG Electronics LS50の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、LG Electronics LS50に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLG Electronics LS50デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。