LiebherrメーカーHC1060の使用説明書/サービス説明書
ページ先へ移動 of 14
Installation Instructions Combined fridge-freezer for integrated use, door-on-door HC 1011/1060 HC 1001/1050 20/08 7084000 - 00.
Contents 1 General safety information ........................... 2 2 Setting up the appliance ............................... 2 3 Changing the door hinges ............................ 3 3.1 To detach the soft stop mechanism.................. 3 3.2 Reversing the door .
u Examine the unit and packaging for shipping damage. Contact the carrier immediately if you suspect there is any damage. u Note the type (model, number), index, appliance/serial number, date of purchase and where purchased on the spaces provided in see Appliance Information.
u Screw in ball stud Fig. 3 ( 3) together with the soft stop mechanism Fig. 3 ( 2) in the fastening hole. u Re-attach all covers Fig. 2 ( 5,6,7,8) . 4 Kitchen Cabinet Construction This is a fully integrated appliance which means that it is fully enclosed by a kitchen cabinet.
Fig. 6 u In the cabinet base, cut out a ventilation opening that is 17-23/32 in. ( 450 mm) in width and 2-7/32 in. (56 mm ) in height. u Insert ventilation grille Fig. 6 ( 3) into the cabinet base cut- out Fig. 6 ( 1) . u From the back side, slide the snap-fits Fig.
w The floor and side walls must be at right angles to each other. The joint between the upper and the lower kitchen cabinet door must align with the joint between the upper and lower appliance door. Follow distance L to the wall to allow the drawers to be pulled out properly.
Fig. 7 1 Unit door fridge compartement 3 Fridge compartement door 2 Unit door freezer comparte- ment 4 Freezer compartement door The freezer door height is 24-24/32 in. (629 mm). u To cover the lower part of the appliance: increase the height of the panel to 27-3/32 in.
u The total opening of the cabinet (i.e. 70-3/8 in. (1788 mm)) plus the thickness of the top as well as the floor board (usually 3/4 in. (19 mm )) minus the height of the freezer door panel (xxx in. (xxx mm)) as calculated above and subtract the width of the gap (approximately 1/8 in.
Note u Before assembling the unit door, make sure that the per- mitted weight for the unit doors is not exceeded. u Otherwise damage to the hinges and malfunctions aris- ing from this cannot be ruled out. Maximum weight of unit door Fridge compart- ment door 30.
u Connect the IceMaker as indicated the section entitled Water Supply.* u Push the appliance 3/4 of the way into the recess. u Remove the covers ( 5,6,7) . u Screw Fig. 11 ( 61) the equal- izer trim Fig. 11 ( 20) to the ap- pliance through the oblong holes on top.
u Slightly loosen the screws Fig. 20 ( 51) . u Secure the bottom mount- ing bracket Fig. 20 ( 50) to the unit wall with a ø4x19 chipboard screw Fig. 20 ( 29) . u Break off the protruding end of the cover Fig. 20 ( 53) . u Tighten the screws Fig. 20 ( 51) .
u To align the unit door in depth Z : Undo the screws Fig. 25 ( 36) at the top and the hex head screws Fig. 25 ( 35) at the bottom using the ring wrench Fig.
- We recommend using a dedicated circuit for this appli- ance to prevent electrical overload. - Follow all Federal, State and local electrical, fire and building codes and ordinances when installing the re- ceptacle and / or the appliance. - In some communities, a wall switch is required to turn power to the appliance ON and OFF.
Connecting the appliance 14.
デバイスLiebherr HC1060の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Liebherr HC1060をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLiebherr HC1060の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Liebherr HC1060の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Liebherr HC1060で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Liebherr HC1060を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLiebherr HC1060の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Liebherr HC1060に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLiebherr HC1060デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
