Life Fitnessメーカー8215の使用説明書/サービス説明書
ページ先へ移動 of 21
8215 MULTI-PRES S Part # 6875601 Revision:3/17/00 1 ASSEMB L Y INSTRUCTIONS.
IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8215 MULTI-PRESS. Please read these instruc- tions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
3 PARTS LIST PART # 6795203 6784303 6755602 6755903 6878202 6783403 6781303 6784703 6784103 6624302 6624203 6651602 6780304 6780004 6791102 6214501 6284501 6714601 3116101 6782301 6784601 6382301 3108.
4 STEP 1: FIGURE 1 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSELY assemble LOWER SUPPORT (6) to the TOWER (1) and PRESS FRAME (2) using four 1/2 X 4 ” BOLTS (31), four 1/2 ” WASHERS (41), and three 1/2 ” LOCK NUTS (43).
STEP 2: FIGURE 2 5 • SECURE LY assemble one 3/8 ” SPRING PIN (48) to the WOLFF SLEEVE (3) as shown in FIGURE 2. (IMPORTANT! Tighten nut of SPRING PIN completely.) • Attach one U-PIN (50) to the WOLFF SLEEVE (3) using one 1/2 ” P AL NUT (24). Slide one 4 ” VINYL CAP (25) onto the U-PIN (50) as shown in FIGURE 2.
STEP 3: FIGURE 3 6 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURE LY assemble the PRESS FRAME (9) to the PRESS BASE (2) using one 1/2 X 3 ” BOLT (32), two 1/2” WASHERS (41), and one 1/2 ” LOCK .
7 STEP 4: FIGURE 4 • Slide two HINGE TABS (46) onto the WOLFF SLEEVE (3) and SECUREL Y assemble SE AT PAD (14) using two 3/8 X 1-1/4 ” BO LTS (39), and two 3/8 ” W ASHERS (42).
STEP 5: 8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Slide the RIGHT BACK PAD ANGLE (10) and the LEFT BACK PAD ANGLE (11) onto the shaft on the WOLFF SLEEVE (3) as shown in FIGURE 5.
FIGURE 6 9 • SECURELY assemble the BACK PAD (13) to the LEFT & RIGHT BACK PAD ANGLES (11 & 10) using four 3/8 X 1-1/4 ” BO LTS (39) and four 3/8 ” W ASHERS (42).
FIGURE 7 10 • Slide two PILLOW BLOCKS (27) over the shaft on the PRESS ARM ADJUST (5) and SECURELY assemble the two PILLOW BLOCKS (27) to the UPPER SUPPORT (8) using four 3/8 X 3-1/4 ” BOLTS (35), four 3/8 ” WASHERS (42), and four 3/8 ” LOCK NUTS (45) as shown in FIGURE 7.
FIGURE 8 11 • SECURELY assemble one 1/2 ” SPRING PIN (47) to the PRESS ARM (4) as shown in FIGURE 8. (IMPORTANT! Tighten spring pin completely.) STEP 8: 29 1/2 X 7-1/2 ” 4 5 44 1/2 ” LOW HEIGH.
12 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 9 STEP 9: • Snap two WEIGHT PLATE BUSHINGS (22) into the top side of all twenty WEIGHT PLATES (16) as shown in FIGURE 9.
FIGURE 10 13 • Insert the two GUIDE RODS (20) into the base of the TOWER (1) as shown in FIGURE 10. Lubricate the GUIDE RODS with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (23) down over the GUIDE RODS (20).
14 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 11 FIGURE 12 STEP 11: • SECURELY assemble two 4-1/2 ” PULLEYS (19) to the TOWER BRACE (7) using two 3/8 X 2 ” BOLTS (38), and two 3/8 ” LOCK NUTS (45).
FIGURE 13 15 STEP 13: • Wrap the CABLE (21) around one 4-1/2 ” PULLEY (19) and SECURELY assemble the pulley to the REAR slot of the PRESS ARM ADJUST (5) using one 3/8 X 2-3/4 ” BO LT (37), two 3/8 ” FLANGE SPACERS (52), and one 3/8 ” LOCK NUT (45) as shown in FIGURE 13.
FIGURE 14 16 STEP 14: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Route the threaded end of the CABLE (21) through the large hole in the PRESS FRAME (9) as shown in FIGURE 14.
FIGURE 15 17 STEP 15: • Wrap the CABLE (21) around one 4-1/2 ” PULLEY (19) and SECURELY assemble the 4-1/2 ” PULLEY (19) to the horizontal pulley bracket on the PRESS FRAME (2) using one 3/8 X 2 ” BOLT (38), one 2-7/8 ” CABLE CLIP (26), and one 3/8 ” LOCK NUT (45) as shown in FIGURE 15.
FIGURE 16 18 STEP 16: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Wrap the CABLE (21) around one 4-1/2 ” PULLEY (19) and SECURE LY assemble the 4-1/2 ” PULLEY (19) to the vertical pulley bracket on the LOWER SUPPORT (6) using two 3/8 X 2 ” BO LTS (38) and two 3/8 ” LOCK NUTS (45) as shown in FIGURE 16.
19 FIGURE 17 STEP 17: • Screw the treaded end of the CABLE (21) approximately 3/4 ” into the end of the WEIGHT STACK SHAFT (17) and tighten jam nut securely.
STEP 18: • Slide the SHROUD (15) between the TOWER (1) as shown in FIGURE 18. FIGURE 18 20 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 15 1.
21 FIGURE 19 STEP 19: 1 15 Thank you for purchasing the LifeFitness 8215 MU LTI-PRESS. If unsure of proper use of equipment, call your local LifeFitness distributor or call the LifeFitness customer service department at (800) 328-9714.
デバイスLife Fitness 8215の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Life Fitness 8215をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLife Fitness 8215の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Life Fitness 8215の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Life Fitness 8215で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Life Fitness 8215を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLife Fitness 8215の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Life Fitness 8215に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLife Fitness 8215デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
