Life Fitnessメーカー8245102の使用説明書/サービス説明書
ページ先へ移動 of 17
Part # 6870101 Revision:01/24/00 1 8245102 LEG PRESS/CALF ASSEMB LY INSTRUCTIONS.
IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8245 LEG PRESS/CAL F . Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
3 PARTS LIST PART # 6802903 6804803 6803802 6780703 6801703 6804102 6803503 6781303 6802002 6803203 6791102 6805101 6523401 6807401 3116101 6284501 6714601 3203501 6808901 6692601 3108002 6809601 KE Y.
STEP 1: FIGURE 1 • LOOSE LY assemble LOWER CROSS SUPPORT (4) to the TOWER (1) using two 1/2 X 4 ” BOLTS (39), two 1/2 ” W ASHERS (40) and one 1/2 ” LOCK NUT (41).
STEP 2: FIGURE 2 • LOOSE LY assemble the FRAME (2) to the LOWER CROSS SUPPORT (4) using two 1/2 X 4 ” BOLTS (39), two 1/2 ” W ASHERS (40) and two 1/2 ” LOCK NUTS (41). See FIGURE 2. • LOOSELY assemble the PIVOT FRAME (6) to the FRAME (2) using four 1/2 X 3 ” BOLTS (38), four 1/2 ” WASHERS (40) and four 1/2 ” LOCK NUTS (41).
STEP 3: FIGURE 3 6 • LOOSELY assemble the PIVOT FRAME (6) to the TOWER (1) using four 1/2 X 4 ” BOLTS (39), four 1/2 ” W ASHERS (40) and three 1/2 ” LOCK NUTS (41) as shown in FIGURE 3. 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECUREL Y TIGHTEN THE FRAME CONNECTIONS IN THE FOLLOWING ORDER: 1 .
7 STEP 4: • Slide two 1-3/4 ” VINYL SLEEVES (22) over the shafts on the PIVOT ARM (7) as shown in FIGURE 4. • Slide one RUBBER BUMPER (21) over the short round tube on the PIVOT FRAME (6) as shown in FIGURE 4.
8 FIGURE 5 STEP 5: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURE LY assemble the FOOTPL ATE (3) to the PIVOT ARM (7) using four 1/2 X 4 ” BOLTS (39), four 1/2” WASHERS (40), and four 1/2 ” LOCK NUTS (41) as shown in FIGURE 5.
STEP 6: 9 • SECURE LY assemble the HANDLE (10) to the FRAME (2) using two 1/2 X 3 ” BOLTS (38), two 1/2” WASHERS (40), and two 1/2 ” LOCK NUTS (41) as shown in FIGURE 6. • Apply two 2-1/2 X 9-1/2 ” NON-SKID STRIPS (19) a foot stance apart on the PIVOT FRAME (6) as shown in FIGURE 6.
• SECURELY assemble one PAD (12) to the FRAME (2) using two 3/8 X 3 ” BO LTS (34) and two 3/8 ” WASHERS (36) as shown in FIGURE 7. 10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 7 STEP 7: 3/8 X .
11 FIGURE 8 STEP 8: STEP 9: FIGURE 9 • Snap two WEIGHT PL ATE BUSHINGS (27) into the top of all twenty WEIGHT PL ATES (29) as shown in FIGURE 9. 27 29 30 3/8 X 1 ” BUTTON HEAD 34 3/8 X 3 ” 9 37 20 24 36 12 2 • SECURE LY assemble the SE AT PAD (12) to the SEAT ADJUST (9) using two 3/8 X 3 ” BOLTS (34) and two 3/8 ” WASHERS (36).
0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 12 FIGURE 10 STEP 12: • Insert two GUIDE RODS (13) into the base of the TOWER (1) as shown in FIGURE 10. Lubricate the GUIDE RODS (13) with a slicon or teflon spray that is available at most hardware stores. • Slide two RUBBER BUMPERS (21) down over the GUIDE RODS (13).
13 FIGURE 12 • Place TOWER BRACE (8) over the GUIDE RODS (13) and SECUREL Y assemble TOWER BRACE (8) to TOWER (1) using two 1/2 X 4 ” BOLTS (39), two 1/2” WASHERS (40), and two 1/2 ” LOCK NUTS (41) as shown in FIGURE 12.
14 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 13 • Route the swivel end of the CABLE (14) through the holes and around the pulleys in the TOWER BRACE (8) as shown in FIGURE 13.
FIGURE 15 15 STEP 15: • SECURELY assemble two 4-1/2 ” PULLEYS (21) to the brackets on the FRAME (2) using three 3/8 X 2 ” BOLTS (32), one CABLE RETAINING CLIP (25), and three 3/8 ” LOCK NUTS (37) as shown in FIGURE 16. (NOTE: Position the CABLE RETAINING CLIP before tightening.
• Screw the threaded end of the CABLE (14) approximately 3/4 ” into the end of the 20 HOLE SELECTOR SHAFT (16) and tighten jam nut securely. See FIGURE 17. • If the HEAD PL ATE (17) does not sit on top of the first WEIGHT PL ATE (29), push the head plate down, insert the SELECTOR PIN (23) and perform several repetitions on the machine.
• SECURE LY assemble the SHROUD (11) to the TOWER (1) using four 3/8 X 1 ” BUTTON HEAD CAP SCREWS (30) as shown in FIGURE 18. FIGURE 18 17 STEP 18: Thank you for purchasing the LifeFitness 8245 LEG PRESS/CAL F .
デバイスLife Fitness 8245102の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Life Fitness 8245102をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLife Fitness 8245102の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Life Fitness 8245102の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Life Fitness 8245102で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Life Fitness 8245102を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLife Fitness 8245102の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Life Fitness 8245102に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLife Fitness 8245102デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
