Life FitnessメーカーCable Motion 39721の使用説明書/サービス説明書
ページ先へ移動 of 24
G5 CABLE MOTION ™ GYM SYSTEM A SSEMBL Y INSTRUCTIONS G5-001 / CLASS H / 09/30/08 / 8289201 REV . B.
2 T ABLE OF CONTENTS Safety S tatement . . . . . . . . . . . . . . . .2 Hardware . . . . . . . . . . . . . . . . . . . . . . .8 G5 W arning Labels . . . . . . . . . . . . . . .4 Assembly Instructions . . . . . . . . . . . . . .10 Gym Dimensions. . . .
3 INSPECTION 1. DO NOT use or permit use of any equipment that is damaged and or has worn or broken part s. For all LIFE FITNESS equipment use only replacement part s supplied by LIFE FITNESS. 2. Cables and Belts pose an extreme liability if used when frayed.
4 NOTE: Lock the weight stack when not using the gym. Make sure all the weight plates are rest- ing on the plate below with no gap in between. Insert the weight selector pin in the tab under- neath the weight stack. The weight selector pin should be inserted until the knob touches the metal t ab.
5 GYM DIMENSIONS Resistance Ratio: 1:2 Machine Weight: 500 pounds Weight S tack: 160 pounds.
6 12” 12” 11’-3” 13’-4” NOTE: The live area shows the extent of the G5 gym. It does not include the user . G5 LIVE AREA.
7 COMPONENTS LIST NOTE: This component list is for ASSEMBL Y ONL Y . For ordering serviceable parts, please go to: http://us.home.lifefitness.com/content.
8 COMPONENTS LIST HARDW ARE ITEM NO. QTY . DESCRIPTION 39 14 3/8” W ASHER 40 4 M10 X 30MM SCREW 41 8 M10 X 70MM SCREW 42 4 M12 X 80MM SCREW 43 8 1/2” W ASHER 44 4 M12 HEX NYLOCK NUT 45 2 M10 X 50 HEX TENSION SCREW 46 2 GUIDE ROD RET AINER 47 4 M4 X 0.
9 HARDW ARE: M10 X 50MM HEX TENSION SCREW (#45) M10 HEX NYLOCK NUT (#53) 3/8” W ASHER (#39) 1/2” W ASHER (#43) M10 X 30MM SCREW (#40) M6 X 60MM SCREW (#51) 1/4” W ASHER (#52) RET AINING RING (#4.
10 STEP 1: Slide the RIGHT BASE (6) over the MOUNTING TUBE (A) of the RIGHT UPRIGHT (4). Loosely secure the RIGHT BASE (6) and RIGHT UPRIGHT (4) to the FRONT UPRIGHT (1) using two M12 x 80mm SCREWS (42), four 1/2” W ASHERS (43), and two M12 HEX NYLOCK NUTS (44) as shown.
11 7 41 39 39 41 6 5 STEP 2: LOOSEL Y attach the FOOTPLA TE (7) to the RIGHT BASE (6) and LEFT BASE (5) using four M10 x 70mm SCREWS (41) and four FLA T 3/8” W ASHERS (39).
12 STEP 3: Position two WEIGHT ST ACK CUSHIONS (13) and GUIDE RODS (8) at the GUIDE ROD BRACKET (B) on the bot- tom of the FRONT UPRIGHT (1). NOTE: MAKE SURE THA T THE PLUGGED ENDS OF THE GUIDE RODS (8) ARE F ACING UP .
2 2 10 14 29 C 13 STEP 4: Remove one QUICK CONNECT from the end of one UPPER (LONG) CABLE (29). Insert the end (where the QUICK CONNECT was removed) of the UPPER (LONG) CABLE (29) through the UPPER SWIVEL PULLEYS (2) and follow routing illustration to the FLOA TING PULLEYS (14) through to the HEAD PLA TE PULLEY (10).
14 STEP 5: Dissemble the QUICK CONNECT (32) by removing the two M5 HEX SCREWS (H) from the QUICK CONNECT COUPLER (D). Carefully remove the COMPRESSION SPRING (G), the QUICK CONNECT SLEEVE (F) and the QUICK CONNECT HOUSING (E). Slide the QUICK CONNECT HOUSING (E), COMPRESSION SPRING (G), and QUICK CONNECT SLEEVE (F) onto the cable as shown.
15 STEP 6: Mount the RIGHT BOTT OM PLA TE (16) and the LEFT BOTTOM PLA TE (17) to the FRONT UPRIGHT (1) using two 10-32 x 3/4” PHILLIPS P AN HEAD SCREWS (50) for each plate.
16 STEP 7: Remove one QUICK CONNECT from the end of one LOWER (SHOR T) CABLE (30). Insert the end (where the QUICK CONNECT was removed) of the the LOWER (SHORT) CABLE (30) through the LOWER RIGHT PULLEY (J) and through the access hole in the FOOTPLA TE (7).
17 STEP 8: Attach the BACK THIGH HOLD CLAMP (18) to the the FRONT UPRIGHT (1) by using two M6 x 60mm SCREWS (51) and two 1/4” W ASHERS (52) from the back of the FRONT UPRIGHT (1).
18 54 20 21 54 STEP 9: Attach the TOP FRONT COVER (21) to the TOP BACK COVER (20) using eight M4 ZINC PHILLIPS P AN HEAD SCREWS (54). DO NOT OVER TIGHTEN SCREWS INTO PLASTIC P ARTS.
19 STEP 10: Insert the ball end of one GUIDE CABLE (31) through the eye hook on one FLOA TING PULLEYS (14). Insert and hook the ball end of the cable into the SLOTTED BUSHING (N) located at the bottom of the frame located directly below the FLOA TING PULLEYS (14).
20 STEP 1 1: Assemble the MOUNTING SHEET (22) to the top of the FRONT UPRIGHT (1) using two M10 x 20mm SCREWS (48) and two 3/8” W ASHERS (39). T ighten screws SECUREL Y . Attach the TOP LEFT COVER (25), the T OP RIGHT COVER (24) and the T OP COVER (23) to the MOUNTING SHEET (22) using four M4 x 0.
27 28 F 26 F 2 36 37 35 34 33 38 21 STEP 12: Referencing step 5, at the UPPER SWIVEL PULLEYS (2) push back on the QUICK CONNECT SLEEVE (F) at the end of each cable and attach the SHOR T HANDLES (26). Repeat the process for attaching the ADJUST ABLE HANDLES (28) to the lower cable ends and the MEDIUM HAN- DLES (27) to the middle cable ends.
22 MAINTENANCE Please note: * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water . T ouch-up paint can be purchased from your Life Fitness cus- tomer service representative at (800) 351-3737. * Inspect equipment before each use.
23 LIMITED W ARRANTY Life Fitness® G5 Cable Motion™ Gym System Life Fitness extends the following LIMITED W ARRANTY to the original owner (proof of purchase required, keep your receipt with this manual) of the Life Fitness product. The W arranty terms apply to IN HOME and LIGHT INSTITUTIONAL USE ONL Y .
C ORPORA TE H EADQUARTERS 5100 North River Road Schiller Park, Illinois 60176 • U.S.A. 847.288.3300 • F AX: 847.288.3703 800.735.3867 (T oll-free within U.S.A., Canada) I NTERNA TIONAL O FFICES G5-001 Rev A 09/08 A MERICA ’ S North America Life Fitness Inc.
デバイスLife Fitness Cable Motion 39721の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Life Fitness Cable Motion 39721をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLife Fitness Cable Motion 39721の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Life Fitness Cable Motion 39721の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Life Fitness Cable Motion 39721で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Life Fitness Cable Motion 39721を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLife Fitness Cable Motion 39721の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Life Fitness Cable Motion 39721に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLife Fitness Cable Motion 39721デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
