Life FitnessメーカーParabody 663の使用説明書/サービス説明書
ページ先へ移動 of 19
1 663 660 SECOND ST ACK OPTION CLASS H PAR T # 7050101 REV . C Revision: 07/31/01 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W H O USE THIS TY PE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THE SE RULES ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 663 660 Second Stack Option. Please read these instructions thoroughly and keep them for future reference. 3 NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOL T .
STEP 2 FIGURE 2 FIGURE 1 STEP 1 • REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD. See FIGURE 1.
STEP 3 FIGURE 3 5 • Unscrew the threaded ends of the HEAD PLA TE CABLE from the WEIGHT ST ACK SHAFT & the D-RING and remove HEAD PLA TE CABLE. The HEAD PLA TE CABLE will be used later .
6 PRESS CABLE (67249) STEP 4 • Remove the PRESS CABLE (67249) from the KEYHOLE CLEVIS and ELASTIC CORD. (NOTE: The LA T or LEG EXT CABLE can be moved over one hole on the D-RING so the KEYHOLE CLEVIS are evenly spaced .) FIGURE 4 ELASTIC CORD D-RING KEYHOLE CLEVIS • Discard the KEYHOLE CLEVIS and ELASTIC CORD.
7 STEP 6 FIGURE 6 • Assemble the previously removed 2” PULLEY to the bracket on the TOP BOOM using one 3/8 X 1” BOL T (1 1), one previously remov ed 3/8” W ASHER, and one previously removed 3/8” LOCK NUT . See FIGURE 6. • (NOTE: STEP 6 is only completed if the 100101 LEG PRESS OPTION is installed otherwise proceed to STEP 7.
FIGURE 8 STEP 8 • Discard the two 3/8 X 1/2” SP ACERS. • Remove two 2” PULLEYS to the rear bracket on the T OP BOOM using one 3/8” THREADED SHAFT , two 3/8” W ASHERS, two 3/8” HEX NUTS, and two 3/8” LOCK NUTS as shown in FIGURE 8. FIGURE 9 STEP 9 • Position the elastic cords over the 2” PULLEYS as shown in FIGURE 9.
STEP 10 • Carefully remove and discard the PRESS CABLE as shown in FIGURE 10. PRESS CABLE (67249) FIGURE 10 9 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2.
10 STEP 1 1 • Route the new PRESS-ST ACK CABLE (5) around the pulleys and l-brackets as shown in STEP 11. (Remove pulleys for ease of installation.) 5 5 FIGURE 1 1 FIGURE 12 STEP 12 PRESS-ST ACK CAB.
FIGURE 14 STEP 14 • LOOSEN the bolts holding the TOP BOOM to the UPRIGHTS. Bolts will have to be removed to install GUIDE RODS (1). See FIGURE 14. 11 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 LOOSEN! TOP BOOM LOOSEN! STEP 13 • Snap two WEIGHT PLA TE BUSHINGS (17) each, into the “ top” side of fifteen WEIGHT PLA TES (16) as shown in FIGURE 13.
FIGURE 15 STEP 15 • Insert two GUIDE RODS (1) into the BASE as shown on FIGURE 15. (NOTE: Lubricate GUIDE RODS (1) with silicon or teflon spray available at most hardware stores.) • Slide two WEIGHT ST ACK SP ACERS (3), two 3/4” W ASHERS (15), and two WEIGHT ST ACK CUSHIONS (8) - IN THA T ORDER - down over the GUIDE RODS (1).
STEP 16 FIGURE 16 13 • W ith the GUIDE RODS (1) securely held in the T OP BOOM. Tighten all TOP BOOM connections. (NOTE: Make sur e the LA T CABLE runs over the top of the bolts in the TOP BOOM.) 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 TIGHTEN! ( NOTE: Make sure LA T CABLE runs over top of bolts in TOP BOOM.
14 HEAD PLA TE CABLE (7041801) STEP 17 FIGURE 17 • Screw one of the threaded ends of the previously removed HEAD PLA TE CABLE approximately 1” into the end of the WEIGHT ST ACK SHAFT . See FIGURE 17. WEIGHT ST ACK SHAFT STEP 18 • Screw the other threaded end of the HEAD PLA TE CABLE approximately 1” into the end of the shaft on the D-RING.
STEP 19 FIGURE 19 15 REAR SHROUD • The rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the plastic SHROUD as shown in FIGURE 19.
STEP 21 FIGURE 21 FIGURE 20 STEP 20 • SECUREL Y attach the four previously removed 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 17 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
18 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES LifeFitnessAtlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 LifeFitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 LifeFitness (UK) Ltd.
デバイスLife Fitness Parabody 663の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Life Fitness Parabody 663をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLife Fitness Parabody 663の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Life Fitness Parabody 663の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Life Fitness Parabody 663で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Life Fitness Parabody 663を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLife Fitness Parabody 663の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Life Fitness Parabody 663に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLife Fitness Parabody 663デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
