Life FitnessメーカーSM50の使用説明書/サービス説明書
ページ先へ移動 of 23
M051-K50-B115 1 5 STA CK MULTI-JUNGLE WITH HIGH & LOW PULLEYS (SM50) UNPA CKING A ND A SSEMBLY INSTRUCTIONS.
SM50 U npacking & Assembly Instructions 2 The SM50 c om es partially assem bled. Follow the steps below to com plete the as sem bly. WA RNING: COMPONENTS O F THE SM50 ARE LARGE AND HEAVY.
SM 50 Unpacking & Assembly Instr uctions 3 UNPA CKING Follow the steps below when unpacking the c om ponents of the SM50. 1. Cut off the shipping wrapper. 2. Remove the parts box a nd shipping boards. 3. Remove the it ems in the part s box. T hese item s are s hown in Figure 1.
SM50 U npacking & Assembly Instructions 4 A SSEMBLY Figure 2 shows an ass em bled SM50. Figure 2. SM50 main components (seats and cables remov ed for clarity). 1. 1 stac k c ell 2. 4 stac k c ell 3. Lat bench 4. Connecting beam 5. Lat top 6. Tric ep top 7.
SM 50 Unpacking & Assembly Instr uctions 5 Figure 3. Set t he weig ht stack cells. 2. Bolt on the teardr op pulle ys above the benches ( see Figure 4) on the 4 s tack cell using two 3/8” x 2-3/4” hex head bolts. Include the 3/8” f lat washer, end cap washers , end caps and 3/8” Nyloc nut.
SM50 U npacking & Assembly Instructions 6 Figure 5. Configura tion for 2-3/4” and 3” bolts. 3. Bolt on the connecting bea m ( part 4 fr om Figure 2) using a 5/8” sock et with extension and com bination wrenc h, to the cells using two of the large 7/16” x 6” bolts, 7/16” washers, and 7/16” nuts , end cap washers and end caps.
SM 50 Unpacking & Assembly Instr uctions 7 4. Mount the 56” lat top (par t T f rom HARDWARE s ection) to the 4- stack cell us ing a 5/8” sock et and com bination wrench. Ins ert two of the large 7/16” by 6” bolts using the hardware configur ation shown in Figure 7.
SM50 U npacking & Assembly Instructions 8 B. Unbolt the top plate and re mov e the guide rods using a 9/16” sock et and com bination wrench (s ee Figure 10).
SM 50 Unpacking & Assembly Instr uctions 9 F. Bolt on the top plate. W ith the top plate on the guide rods , bolt on the top plate to the top of the cells as shown in Figure 11 us ing a 9/16” sock et and com bination wrench and the 3” bolts ( with cap washers) that were previous ly inserted.
SM50 U npacking & Assembly Instructions 10 7. Mount the seated row and lat bench to the frame. Using the bolts specif ied in Figure 12 and a 9/16” soc ket and c om bination wrenches, m ount the benches as shown in Figures 13 and 14. 3/8 x 3” (2) 3/8 x 2-3/4 ” (8) Use a pi nch ba r to a lign the seat fram e hol es to the cube s Figure 13.
SM 50 Unpacking & Assembly Instr uctions 11.
SM50 U npacking & Assembly Instructions 12 INSTA LLING THE CABLES The SM50 us es five cables . Ther e are three dif ferent types of cable us ed on the SM50. They are: 1. Crossover cables ( ball end cables) ( 2). 2. Low row cable (the long cables) (1).
SM 50 Unpacking & Assembly Instr uctions 13 CROSSOVER CABLE RO UTI NG Once you’ve removed the pulleys as desc ribed previously, route the cros sover cables on the 4-stack c ell as shown in Figure 16. T he cros sover c able is routed at the f actory on the 1-stack cube.
SM50 U npacking & Assembly Instructions 14 LOW RO W CABLE RO UTING Route the low row cable as shown in Figure 17. Figure 17. Low row cable routing.
SM 50 Unpacking & Assembly Instr uctions 15 Bolt the cable to the weight stack s as s hown in Figure 18. Thr ead the 7/8” nut up on the cable bolt as shown at lef t. Screw the bolt down into the weight stack as shown at right. Tighten the bolt with a 7/8” com bination wrench.
SM50 U npacking & Assembly Instructions 16 TRICEP PUSHDOW N CABLE RO UTI NG Route the tricep pushdown cable as shown in Figure 20. Screw the cable into the weight stac k as shown previously in Figure 18.
SM 50 Unpacking & Assembly Instr uctions 17 HA RDWARE 0123456 ½½½½½½ Hardware F igure 1. Assembly Parts..
SM50 U npacking & Assembly Instructions 18 The parts shown in Hardware Figure 1 are us ed to assem ble the SM50. T hey are: A. 7/16” x 6” hex head bolt (used to bolt the tric ep top beam , adjustable c rossover top beam, lat top beam , and c onnecting beam to the tops of the cells) B.
SM 50 Unpacking & Assembly Instr uctions 19 The part s hown in Hardware Figure 2 is the 9/16” c able jam nut that’s used to s ecure the cables to the weight stack s. Hardware Figure 2. Cable ja m nut. M. Cable jam nut Hardware Figure 3 shows the types of cables that ar e included with the SM50.
SM50 U npacking & Assembly Instructions 20 Hardware F igure 5. T op assemblies. S. Teardr op pulleys (bolt on above lat and seated row bench) (2) T.
SM 50 Unpacking & Assembly Instr uctions 21 Hardware Figure 6. Weight stack rubber bumpers. W . W eight s tack rubber bum pers (inserted under weight stac ks ) (8) Hardware Figure 7.
SM50 U npacking & Assembly Instructions 22 PA RTS LIST Part # ID Description Quantity Main components 1 2 3 4 5 6 7 8 9 1-stac k c ell 4-stac k c ell Low row bench Connecting beam Lat top Tr icep .
SM 50 Unpacking & Assembly Instr uctions 23 0017-00101-1413 0017-00104-0368 0017-00103-0217 Pulley hardw are (installed) 1-3/4” Bolt Cap washer 3/8” Nyloc nut 0017-00101-1413 0017-00104-0313 0.
デバイスLife Fitness SM50の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Life Fitness SM50をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLife Fitness SM50の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Life Fitness SM50の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Life Fitness SM50で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Life Fitness SM50を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLife Fitness SM50の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Life Fitness SM50に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLife Fitness SM50デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
