Life FitnessメーカーSM60の使用説明書/サービス説明書
ページ先へ移動 of 21
M051-K50-A136 1 6 STA CK MULTI-JUNGLE (SM60) WITH HIGH & LOW PULLEYS UNPA CKING A ND A SSEMBLY INSTRUCTIONS.
SM60 U npacking & Assembly Instructions 2 The SM60 c om es partially assem bled. Follow the steps below to com plete the as sem bly. WA RNING: COMPONENTS O F THE SM60 ARE LARGE AND HEAVY.
SM 60 Unpacking & Assembly Instr uctions 3 UNPA CKING Follow the steps below when unpacking the c om ponents of the SM60. 1. Cut off the shipping wrapper. 2. Remove th e parts boxes an d shippin g boards. 3. Remove th e items in the part s boxes. T hese item s ar e shown in Figure 1.
SM60 U npacking & Assembly Instructions 4 A SSEMBLY Figure 2 shows an ass em bled SM60. Figure 2. SM60 main compone nts. 1. Cubes (2) 2. Lat bench ( 2) 3. Connecting beam (1) 4. Lat tops (2) 5. T ricep top (1) 6. 300 lb. W eight stack s (3) 7. 190 lb.
SM 60 Unpacking & Assembly Instr uctions 5 Figure 3. Set t he w eight stack cu bes. 2. Bolt on the teardr op pulleys above the benches (see Figure 4) on both cubes using two 3/8” x 2-3/4” hex head bolts (us ed to bolt the cross beam to the cross mem ber s and the adjus table pulley tops to the top beam s).
SM60 U npacking & Assembly Instructions 6 Figure 4. Bolt on the te ardrop pulleys. Figure 5. Configura tion for 6” bolts..
SM 60 Unpacking & Assembly Instr uctions 7 Figure 6. Configura tion for 2-3/4” and 3” bolts. 3. Bolt on the connecting bea m ( part 3 fr om Figure 2) using a 5/8” sock et with extension and com bination wrenc h, to the cubes using two of the large 7/16” x 6” bolts, 7/16” washers , and 7/16” nuts, end cap washer s and end caps.
SM60 U npacking & Assembly Instructions 8 150 lb. weight stack 300 l b. weight st ack 150 lb. weig ht stack Figure 8. Mount rubber bumpers and the w eight stacks. 5. Install the w eight stacks. T o do this: A. Using a 9/16” soc ket and c om bination wrench, rem ove the tric ep back rest bolts (see Figure 9) .
SM 60 Unpacking & Assembly Instr uctions 9 C. Prepare the w eight stack. Slide the guide rods ( 2) through the weight stack s (1) as shown below. Place rubber bum pers (3) on the bottom s of each guide rod. Make s ure the pull pin (4) is in the bottom weight plate.
SM60 U npacking & Assembly Instructions 10 6. Bolt the f loating pu lleys into the 190 lb w eight stacks used f or the cros sovers using a 7/8” com bination wrenc h. You will need to remove the pulley from the housing to thread the plug into the weight stack bayonet.
SM 60 Unpacking & Assembly Instr uctions 11 Use a pinch bar to al ign the seat f rame holes to th e cubes Figure 13. Mount the benche s to the frame.
SM60 U npacking & Assembly Instructions 12 INSTA LLING THE CABLES The SM60 us es six c ables. T here are two diff erent types of cable used on the SM60. T hey are: 1. Crossover cables ( ball end cables) ( 2). 2. Lat pulldown and tricep cables ( 4).
SM 60 Unpacking & Assembly Instr uctions 13 CROSSOVER CABLE RO UTI NG Once you’ve removed the pulleys as desc ribed previously, route the two crossover cables as shown in Figure 16. Figure 16. Cr os sov er cable routing. Bolt the cable to the weight stack s as s hown in Figure 17.
SM60 U npacking & Assembly Instructions 14 Figure 17. Screw the cable in to th e weigh t stack. LAT PULLDOWN CABLE RO UTI NG Route the lat pulldown cable as shown in Figure 18. Scr ew the cable into the weight stack as shown previously in Figure 18.
SM 60 Unpacking & Assembly Instr uctions 15 TRICEP PUSHDOW N CABLE RO UTI NG Route the tricep pushdown cable as shown in Figure 19. Screw the cable into the weight stac k as shown previously.
SM60 U npacking & Assembly Instructions 16 HA RDWARE 0123456 ½½½½½½ Hardware F igure 1. Assembly Parts..
SM 60 Unpacking & Assembly Instr uctions 17 The parts shown in Hardware Figure 1 are us ed to assem ble the SM60. T hey are: A. 7/16” x 6” hex head bolt (used to bolt the tric ep top beam s, lat top beam s, and connecting beam to the tops of the cubes) B.
SM60 U npacking & Assembly Instructions 18 Hardware F igure 4. T op assemblies. S. Teardr op pulleys (bolt on above lat pulldown) (2) T. 56” Lat tops (bolt to top of cells with pulleys above lat benches) (2) U.
SM 60 Unpacking & Assembly Instr uctions 19 Hardware Figure 5. Weight stack rubber bumpers. W . W eight s tack rubber bum pers (inserted under weight stac ks ) Hardware Figure 6.
SM60 U npacking & Assembly Instructions 20 PA RTS LIST Part # ID Description Quantity Main components 1 2 3 4 5 6 7 Cubes Lat bench Connecting beam Lat top Tr icep top 300 lb weight stack 190 lb w.
SM 60 Unpacking & Assembly Instr uctions 21 0017-00101-1413 0017-00104-0368 0017-00103-0217 Pulley hardw are (installed) 1-3/4” Bolt Cap washer 3/8” Nyloc nut 0017-00101-1413 0017-00104-0313 0.
デバイスLife Fitness SM60の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Life Fitness SM60をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLife Fitness SM60の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Life Fitness SM60の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Life Fitness SM60で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Life Fitness SM60を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLife Fitness SM60の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Life Fitness SM60に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLife Fitness SM60デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
