LinearメーカーAE-500の使用説明書/サービス説明書
ページ先へ移動 of 16
AE-500 T elephone Entr y & Access Control System PRINTER’S INSTRUCTIONS: INSTR,F ACILITY MANA GER,AE-500 - LINEAR P/N: 221000 E - INK: BLACK - MA TERIAL: 20 LB .
2 Contents Introduction The Model AE-500 T elephone Entry & Access Control System is designed for use as a primary access control device f or gated communities, parking garages, offi ce buildings, apartments, dor mitories, hotels/motels, commercial buildings and recreational f acilities with up to 250 residents or users.
3 Sys tem F eatur es DI S PLAY CABINET LOCK OPTIONAL PO S TAL LOCK S PEAKER KEYPAD LIGHTING KEYPAD MICROPHONE Your access control installation company has set this master password for this installation: _______________________ Use this password to enter programming mode.
4 P r ogramming with a Computer The AE-500’ s built-in progr amming interface can be accessed on-site (using a separate telephone line) or off-site using a computer with a modem and any Internet browser (if using Netscape, be sure J ava is installed).
5 Set ting up Multiple Units The system suppor ts up to se ven AE-500s connected to the same telephone line. Some telephone systems ma y only suppor t up to four units on the same telephone line. In multiple-unit installations each AE-500 m ust be assigned a unique unit number bef ore programming.
6 P r ogramming Over the T elephone The system can be programmed using a T ouchT one™ telephone. The telephone’ s ke ypad will act similar to the AE-500’ s local keypad. Connecting with a T elephone 1. Place a call to the telephone number of the line that AE-500 is connected to .
7 P r ogramming Refer ence PROGRAMMING CONTROL USAGE KEYSTROKES ENTER PROGRAMMING FROM LOCAL KEYP AD . . . . . . . . Press 0 and 2 then MASTER P ASSWORD ENTER PROGRAMMING FROM TELEPHONE . . . .Call, wait for tone then enter MASTER PASSWORD ESCAPE/CANCEL .
8 Resident Data P r ogramming Up to 250 resident names and telephone numbers can be set. Each resident entry is assigned a director y number . The director y numbers are the numbers visitors enter to hav e the system call the residents. ✦ NO TE: When entering resident names, programming the AE-500 from a computer is the pref erred method.
9 Entr y Code Programming Changing the Entr y Code Length The factory setting for the entry code length is 4 digits. It can be set to 2-6 digits. 1. If not already in Programming Mode, connect b y telephone or use the local ke ypad. Enter the master password and access prog ramming.
10 Wir eless T ransmit ter Pr ogramming Up to 500 wireless transmitters can be used with the system. T ransmitters can be ordered in pre-programmed b locks of sequential ID codes. Up to 16 blocks of transmitters can be used. T ransmitter bloc ks can be ordered with a F acility Code of 1-15 for b lock identifi cation if desired.
11 Wir eless T ransmit ter Pr ogramming (Continued) Activate a T ransmitter If a transmitter has been suspended, it can be activated again with these programming steps. 1. If not already in Programming Mode, connect b y telephone or use the local ke ypad.
12 Sys tem Options For most installations the f actory settings for the system will be appropriate. Y our installer may ha ve already customized some of the system settings .
13 Sys tem Options (Continued) Speaker T one on Relay Channel “A” Activation The factory setting will not cause the speaker to sound a tone when access is granted with Rela y Channel “A”. The tone can be turned on if desired. 1. If not already in Programming Mode, connect b y telephone or use the local ke ypad.
14 Sys tem Utilities Sev eral utility commands are av ailable f or the system. Utilities can be used to clear memory , display system information, and control the relays . Display Unit Number In multi-unit installations the unit number of each AE-500 can be displa yed.
15 AE-500 Operation Requesting Access with an Entr y Code • Residents hav e up to 40 seconds to ke y in their entr y code. • Up to eight seconds are allowed betw een each keystrok e.
Copyright © 2008 Linear LLC 221000 E T r oubleshooting System completely dead 1. Call installation company f or ser vice. Buzz on speaker 1. Call installation company f or ser vice. Buzz on telephone line 1. Call installation company f or ser vice. System will not answer an incoming call 1.
デバイスLinear AE-500の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Linear AE-500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLinear AE-500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Linear AE-500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Linear AE-500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Linear AE-500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLinear AE-500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Linear AE-500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLinear AE-500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
