LinksysメーカーWPS54GU2の使用説明書/サービス説明書
ページ先へ移動 of 76
A Division of Cisco Systems, Inc. ® Model No. PrintServer for USB 2.0 Wireless- G WPS54GU2 User Guid e WIRELESS GH z 2.4 802.11g.
Wireless-G PrintServer for USB 2.0 Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2003 Cisco System s, Inc.
Wireless-G PrintServer for USB 2.0 Table of Contents Chapter 1: Introduction 1 Welcome 1 What’s in this Guide? 1 Chapter 2: Getting to Know the PrintServer 3 The Back Panel 3 The Front Panel 4 Chapt.
Wireless-G PrintServer for USB 2.0 Starting the Bi-Admin Management Utility 30 The Bi-Admin Mana gement Utility 31 Chapter 8: Internet Printing Protocol (IPP) 42 Overview 42 Windows IPP Client Setup 4.
Wireless-G PrintServer for USB 2.0 List of Figures Figure 2-1: PrintServer’s Back Panel 3 Figure 2-2: PrintServer’s Front Panel 4 Figure 3-1: Connecting to the LAN Port 5 Figure 3-2: Connecting to.
Wireless-G PrintServer for USB 2.0 Figure 6-6: Protocol Tab - SNMP 21 Figure 6-7: Wireless Tab - Basic 22 Figure 6-8: Wireless Tab - Security 23 Figure 6-9: Printer - Internet Printing 24 Figure 6-10:.
Wireless-G PrintServer for USB 2.0 Figure 8-2: Output Select 43 Figure 8-3: AddPort 43 Figure 8-4: Configure IPP Port 44 Figure 8-5: Locate Your Printer 44 Figure 8-6: Connect to Printer 45 Figure B-1.
1 Chapter 1: Introductio n Welcome Wireless-G PrintServer for USB 2.0 Chapter 1: Introduction Welcome Thank you for choosing the Linksys Wireless-G PrintServer for USB 2.
2 Chapter 1: Introductio n What’s in this Guide? Wireless-G PrintServer for USB 2.0 • Chapter 5: Windows Driver Installation This chapter explains how to install the Windows driver for the PrintServer.
3 Chapter 2: Getting to Know the PrintServer The Back Panel Wireless-G PrintServer for USB 2.0 Chapter 2: Getting to Know the PrintServer The Back Panel The PrintServer’s ports are located on the back panel. Power The Power port is where you will connect the power adapte r.
4 Chapter 2: Getting to Know the PrintServer The Front Panel Wireless-G PrintServer for USB 2.0 The Front Panel The PrintServer’s LEDs are located on the front panel. Status Green/Orange. If the Status LED is continuously lit green, then t he PrintServer is ready for use.
5 Chapter 3: Connecting the PrintServer Overview Wireless-G PrintServer for USB 2.0 Chapter 3: Connecting the PrintServer Overview Before starting the physical installation, make a note of the PrintServer’s Default Name, which is located on the bottom of the PrintServer.
6 Chapter 4: Configuring th e PrintServer Using the Setup Wizard Installation Wireless-G PrintServer for USB 2.0 Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation To install the PrintServer, you will use the Setu p CD-ROM to run the Setup Wizard.
7 Chapter 4: Configuring th e PrintServer Using the Setup Wizard Installation Wireless-G PrintServer for USB 2.0 4. The Password screen, Figure 4-3, will appear next. Enter the default password admin in the field provided. Click Enter . 5. The Basic Settings screen, shown in Figure 4-4, will appear.
8 Chapter 4: Configuring th e PrintServer Using the Setup Wizard Installation Wireless-G PrintServer for USB 2.0 6. The IP Settings screen, Figure 4-5, will appear. If your network uses a router with a DHCP setting that automatically assigns IP addresses, select Automatically obtain an IP address (DHCP) .
9 Chapter 4: Configuring th e PrintServer Using the Setup Wizard Installation Wireless-G PrintServer for USB 2.0 8. The Wireless Settings screen will appear. In th e SSID field, enter your wireless network’s SSID or name. This is the unique name shared by all devices in a wireless network.
10 Chapter 4: Configuring th e PrintServer Using the Setup Wizard Installation Wireless-G PrintServer for USB 2.0 9. The Wireless Security Settings screen, shown in Figure 4-8, will appear.
11 Chapter 4: Configuring th e PrintServer Using the Setup Wizard Installation Wireless-G PrintServer for USB 2.0 10. If you entered a Passphrase, you will see the auto ma tically generated WEP key on the following screen, as shown in Figure 4-9. Otherwise, enter the W EP key manually in the field provided.
12 Chapter 4: Configuring th e PrintServer Using the Setup Wizard Installation Wireless-G PrintServer for USB 2.0 12. The Congratulations screen, shown in Figure 4-11, will appear.
13 Chapter 5: Windows Driver Installation Overview Wireless-G PrintServer for USB 2.0 Chapter 5: Windows Driver Installation Overview This section installs the PrintServer’s software on your Windows 98, Me, 2000, or XP computers so they can use the PrintServer for print jobs.
14 Chapter 5: Windows Driver Installation Installation Wireless-G PrintServer for USB 2.0 4. The Welcome screen of the driver installation program, Figure 5-2, will appear first. Click Cancel to quit the setup program and then close the open programs.
15 Chapter 5: Windows Driver Installation Installation Wireless-G PrintServer for USB 2.0 6. The Select Program Folder screen will appear, as shown in Figure 5-4. An icon will be added to the pro gram folder listed. You may change the name for t he program folder, if you wish.
16 Chapter 5: Windows Driver Installation Starting the Print Driver Utility Wireless-G PrintServer for USB 2.0 Starting the Print Driver Utility 1. Click Start , Programs , Print Server Util ity , and then Print Driver Setup . If the Print Driver Setup icon has been created, you can double-click it instead.
17 Chapter 5: Windows Driver Installation Starting the Print Driver Utility Wireless-G PrintServer for USB 2.0 5. The Configure Printer Port screen will app ear, as sho wn in Figure 5-8.
18 Chapter 6: Configuring the PrintServe r Using the Web-based Utility Overview Wireless-G PrintServer for USB 2.0 Chapter 6: Configuring the PrintServer Using the Web-based Utility Overview After setting up the PrintServer with the Setup Wizard, the PrintServer will be ready for use.
19 Chapter 6: Configuring the PrintServe r Using the Web-based Utility The Protocol Tab - TCP/IP Wireless-G PrintServer for USB 2.0 The Protocol Tab - TCP/IP Click the TCP/IP tab to view or change the TC P/IP values of th e Prin tServer. (See Figure 6-3.
20 Chapter 6: Configuring the PrintServe r Using the Web-based Utility The Protocol Tab - NetB EUI Wireless-G PrintServer for USB 2.0 The Protocol Tab - NetBEUI NetBEUI connection settings of the PrintServer are available on this tab. (See Figure 6-5.
21 Chapter 6: Configuring the PrintServe r Using the Web-based Utility The Protocol Tab - SNMP Wireless-G PrintServer for USB 2.0 The Protocol Tab - SNMP Use the screen shown in Figure 6-6 to view or c hange the PrintServer’s SNMP (Simple Network Management Protocol) settings.
22 Chapter 6: Configuring the PrintServe r Using the Web-based Utility The Wireless Tab - Basic Wireless-G PrintServer for USB 2.0 The Wireless Tab - Basic This screen allows you to change the PrintServer’s basic wireless settings. Configuratio n . The PrintServer’s Regulatory Domain and MAC Address are listed and cannot be cha nged.
23 Chapter 6: Configuring the PrintServe r Using the Web-based Utility The Wireless Tab - Security Wireless-G PrintServer for USB 2.0 The Wireless Tab - Security Configure or alter the Prin tServer’s wireless security settings on this screen. Wireless Security • WEP Encryption .
24 Chapter 6: Configuring the PrintServe r Using the Web-based Utility The Printer Tab - Internet Printin g Wireless-G PrintServer for USB 2.0 The Printer Tab - Internet Printing Internet Printing allows you to automatically print any e-mails that are sent to a specific e-mail account on your network.
25 Chapter 6: Configuring the PrintServe r Using the Web-based Utility The Printer Tab - Logical Port Wireless-G PrintServer for USB 2.0 The Printer Tab - Logical Port The Logical Printers tab contains the logical printer settings of the PrintServer. Config ure them for each Logica l Printer.
26 Chapter 6: Configuring the PrintServe r Using the Web-based Utility The Status Tab - Device Wireless-G PrintServer for USB 2.0 The Status Tab - Device The Device tab allows you to view information about the PrintServer. No value s can be changed on this screen.
27 Chapter 6: Configuring the PrintServe r Using the Web-based Utility The Status Tab - Wireles s Wireless-G PrintServer for USB 2.0 The Status Tab - Wireless The Wireless tab allows you to view information about the PrintServer’s wireless connection.
28 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement Overview Chapter 7: Bi-Admin Management Overview If you use Windows, then you can manage the PrintServ er using its web-based util.
29 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement Bi-Admin Installation 5. The Choose Destination Location screen will appear, as shown in Figure 8-3. Ch oose the location where the B-Admin folder will be installed. To install the driver in the default location, click Next .
30 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement Starting the Bi-Admin Manag ement Utility Starting the Bi-Admin Management Utility 1. To start the Bi-Admin program, click Start , Programs , Print Server Utility , and then Bi-Adm in Management Utility .
31 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility The Bi-Admin Management Utility The Bi-Admin Management Utility screen will appear next. Any hardware found on the network will appear on the left-hand side of the screen, as shown in Figure 8-7.
32 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility • Printer Status . This op tion allows you to view the printer stat us, as well as set port and printer parameters. If you click this option, a Verify Password screen will appear.
33 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility • Configure . You may configure the P rintServer with this option.
34 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility TCP/IP (Figure 8-13) • Dynamic IP Address (DHCP) . If your network router is using DHCP to assign IP addresses, select Dynamic IP Address (DHCP) .
35 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility Apple Talk (Figure 8-14) • Zone Name . Typically only Macintoshes use AppleTalk, although other platform s can use it if they have the necessary, third-party software installed.
36 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility NetBEUI (Figure 8-15) • Domain Name . Enter the name of the domain tha t you want the Prin tServer assoc iated with in the Domain Name field.
37 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility Interne t Printing (Figure 8-16) • Mail Server . Enter the address of your mail server in the M ail Server IP Address fields. (This value must be a fixed IP address.
38 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility Port (Figure 8-17) • Physical Port . Select the number of the Selected Physical Port from the drop-down menu. Select th e Handshake Signal, Busy Only or Busy & Ack .
39 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility Wireless (Figure 8-18) • SSID (Service Se t Identifier) . In the SSID field, enter the name of your wireless network. This is the unique name shared by all devices in a wireless network.
40 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility SNMP (Figure 8-19) • SysContact . Enter the name of the con tact person in the SysContact field. • SysLocation . Enter the location of the contact person in th e SysLocation field.
41 Wireless-G PrintServer for USB 2.0 Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility • Upgrade . You may use this option to upgrade the firmware of the PrintServer. Follow these instructions: 1 On the Upgrade screen shown in Figure 8-20, click the Files button.
42 Chapter 7: Internet Printing Prot ocol (IPP) Overview Wireless-G PrintServer for USB 2.0 Chapter 8: Internet Printing Protocol (IPP) Overview Internet Printing Protocol (IPP) is a standards-based system that allows remote printing from a PC to any accessible printer.
43 Chapter 7: Internet Printing Prot ocol (IPP) Windows IPP Client Setup Wireless-G PrintServer for USB 2.0 2. Enter the IP Address or URL of the IPP Server. 3. If Internet access from your location is via a Proxy Server, check Access IPP Server via Proxy Server , and enter details of your Proxy Server.
44 Chapter 7: Internet Printing Prot ocol (IPP) Windows IPP Client Setup Wireless-G PrintServer for USB 2.0 Changing the IPP Port Settings After the IPP port is created, you can reach the Configure IPP Port screen by performing these steps: 1. Open the Printers folder ( Start => Settings => Printers ).
45 Chapter 7: Internet Printing Prot ocol (IPP) Windows IPP Client Setup Wireless-G PrintServer for USB 2.0 4. If the connection can be established, and the printer on that port is on line, the dialog box shown in Figure 7-6 will be displayed. This screen notifies you that th e printer driver is not installed.
46 Appendix A: Common Problems and So lutions Wireless-G PrintServer for USB 2.0 Appendix A: Troubleshooting This appendix consists of “Common Problems and Solution s”. Provid ed are possible solutions to problems that may occur during the installa tion and operation of the Pr intServer.
47 Appendix A: Common Problems and So lutions Wireless-G PrintServer for USB 2.0 7. To start over, I need to set the Prin tServer to its factory default settings. Unplug the PrintServer’s power adapter. Press the Reset button while you plug in the PrintServer’s power adapter.
48 Appendix B: Wireless Security A Brief Overview Wireless-G PrintServer for USB 2.0 Appendix B: Wireless Security A Brief Overview Whenever data—in the form of files, em ails, or messages—is transmitted over your wireless network, it is op en to attacks.
49 Appendix B: Wireless Security What Are The Risks? Wireless-G PrintServer for USB 2.0 But even WEP has its problems. WEP’s encryption algorithm is referred to as “simple”, which also means “weak”, because the technology that scrambles the wireless signal isn’t too h ard to crack for a persistent hacker.
50 Appendix B: Wireless Security What Are The Risks? Wireless-G PrintServer for USB 2.0 Active Attacks Hackers use Active Attacks for three purposes: 1) st ealing data, 2) using your network, an d 3) modifying your network so it's easier to hack in the next time.
51 Appendix B: Wireless Security What Are The Risks? Wireless-G PrintServer for USB 2.0 examples below, your implementation and ad ministration of network security measures is the key to maximizing wireless security. No preventative measure will guaran tee network security but it will make it more difficult for some one to hack into your network.
52 Appendix B: Wireless Security What Are The Risks? Wireless-G PrintServer for USB 2.0 5) SSID There are a few things you can do to make your SSID more secure: a. Disable Broadcast b. Make it unique c. Change it often Most wireless networking devices will give you the option of broadcasting the SSID.
53 Appendix B: Wireless Security What Are The Risks? Wireless-G PrintServer for USB 2.0 PCs unprotected by a firewall router should at leas t run firewall software, and all PCs should run up-to-date antiviral software. 8) WEP Wired Equivalent Privacy (WEP) is often looked upon as a panace a for wireless security concerns.
54 Appendix B: Wireless Security What Are The Risks? Wireless-G PrintServer for USB 2.0 The solution, then, is to segment your network up into multiple groups. If your network had 80 users and you used four WEP keys, a hacker would have access to o nly ¼ of your wireless network resources.
55 Appendix C: About Bi- Directional Printing Wireless-G PrintServer for USB 2.0 Appendix C: About Bi-Directional Printing Normal printing only sends print signals from a PC to a printer.
56 Appendix D: Upgradin g Firmware Wireless-G PrintServer for USB 2.0 Appendix D: Upgrading Firmware The PrintServer’s firmware is upgraded through the Bi -Admin Management utility. Follow these instructions: 1. Download the firmware from Linksys’s website at www.
57 Appendix E: Windows Help Wireless-G PrintServer for USB 2.0 Appendix E: Windows Help All Linksys wireless products require Microsoft Windows. Windows is the most used operatin g system in the world and comes with many features that help make networking easier.
58 Appendix F: Glossary Wireless-G PrintServer for USB 2.0 Appendix F: Glossary 802.11a - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz. 802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.
59 Appendix F: Glossary Wireless-G PrintServer for USB 2.0 Buffer - A block of memory that temporarily holds data to be worked on later when a device is currently too busy to accept the data. Cable Modem - A device th at connects a computer to the cable television network, which in turn connects to the Internet.
60 Appendix F: Glossary Wireless-G PrintServer for USB 2.0 Dynamic IP Address - A temporary IP address assigned by a DHCP server. Encryption - Encoding data to prevent it from being read by unauthorized pe ople. Ethernet - An IEEE standard network protocol that specifie s how data is placed on an d retrieved from a common transmission medium.
61 Appendix F: Glossary Wireless-G PrintServer for USB 2.0 IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. IPSec (Internet Protocol Security) - A VPN protocol used to implem ent secure exchange of packets at the IP layer.
62 Appendix F: Glossary Wireless-G PrintServer for USB 2.0 PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides a uthentication (username and password) in addition to data transport.
63 Appendix F: Glossary Wireless-G PrintServer for USB 2.0 TCP/IP (Transmission Control Protocol/Internet Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent. Telnet - A user command and TCP/IP protocol used for accessing remote PCs.
64 Appendix G: Specification s Wireless-G PrintServer for USB 2.0 Appendix G: Specifications Model WPS54GU2 Standards IEEE 802. 11g, IEEE 802.11b, IEEE 802.
65 Appendix H: Warranty Informat ion Wireless-G PrintServer for USB 2.0 Appendix H: Warranty Information LIMITED WARRANTY Linksys warrants to the original end user purc haser (“You”) that, for a period o f thre e years, (the “Warranty Period”) Your Linksys product will be free of defects in materials and workmanship un der normal use.
66 Appendix I: Regulato ry Information Wireless-G PrintServer for USB 2.0 Appendix I: Regulatory Information FCC STATEMENT This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules.
67 Appendix I: Regulato ry Information Wireless-G PrintServer for USB 2.0 INDUSTRY CANADA (C ANADA) This Class B digital apparatus complies with Canadian ICES-003.
68 Appendix I: Regulato ry Information Wireless-G PrintServer for USB 2.0 • France F: 2.4 GHz Bande : les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz respectivement) sont complétement libres d'utilisation en France (en utilisation in térieur).
69 Appendix J: Contact Informa tion Wireless-G PrintServer for USB 2.0 Chapter J: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.
デバイスLinksys WPS54GU2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Linksys WPS54GU2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLinksys WPS54GU2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Linksys WPS54GU2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Linksys WPS54GU2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Linksys WPS54GU2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLinksys WPS54GU2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Linksys WPS54GU2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLinksys WPS54GU2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。