AppleメーカーXserve 073-0711の使用説明書/サービス説明書
ページ先へ移動 of 13
073-0711 Re v . B Xserve Logic Board with Processor/Heatsink Replacement Instructions F ollow the instructions in this sheet carefully . F ailure to f ollo w these instructions could damage your equipment and v oid its w arranty . Note: Online instructions cov ering customer-installable par ts are av ailab le at http://www .
Xserve Logic Board with Processor/Heatsink - 2 3. If the ser v er is in the loc k ed position (the y ello w security LED on the front panel is on), use the Allen ke y that came with the server to unloc k it. 4. If the cable management arm is not in use, unplug all e xternal cables e xcept the pow er cord.
Xserve Logic Board with Processor/Heatsink - 3 8. Grasp the thumbscre ws and slide the bottom housing f orward part wa y to e xpose the two chassis le v ers . (Figure 2) 9. While depressing both le v ers , pull the bottom housing all the w a y forw ard and remo v e it from the rac k.
Xserve Logic Board with Processor/Heatsink - 4 Removing the Installed Logic Board Note: The replacement logic board does not include memor y DIMMs or expansion cards .
Xserve Logic Board with Processor/Heatsink - 5 Dual-Slot Riser 1. Release the thumb screw that secures the card to the bac k of the server . (Figure 4) 2. Disconnect the riser from the logic board and remov e the riser from the ser ver . Figure 4 Single-Slot Riser 1.
Xserve Logic Board with Processor/Heatsink - 6 2. Pull the clip on the riser forw ard to release the riser from the logic board connector . (Figure 6) 3. Disconnect the riser from the logic board and remov e the riser and card from the ser v er . Figure 6 Heatsink Duct 1.
Xserve Logic Board with Processor/Heatsink - 7 A T A Controller Board 1. Disconnect the blo wer cab le nearest the A T A controller board. (Figure 8) 2. Press in on both ends of the clip securing the r ight side of the A T A controller board and remov e the clip from the server .
Xserve Logic Board with Processor/Heatsink - 8 P ower Supply 1. Release the locking latch on the po wer supply cab le connector and disconnect the cable from the driv e interconnect board. (Figure 9) 2. Release the thumbscrew that secures the po wer supply to the chassis .
Xserve Logic Board with Processor/Heatsink - 9 Logic Board 1. Release the thumb screw that secures the logic board to the chassis . (Figure 10) 2. Mov e the logic board f orw ard and up slightly to release it from the f our mounting pegs. 3. Tilt up the end of the logic board nearest the blo wers so that the board ports clear the chassis.
Xserve Logic Board with Processor/Heatsink - 10 2. Install the replacement logic board in the bottom housing, making sure the board fits ov er the f our mounting pegs on the chassis floor . W arning: When replacing the logic board, make sure the ports and the identifier button on the bac k of the boar d align with the openings in the chassis.
Xserve Logic Board with Processor/Heatsink - 11 8. Reinstall the two A T A controller clips. Note: When replacing the ATA controller board clips, orient them so that the long end of each clip points away from the middle of the server. Place the inside edge of the clip into the small notch and then snap down the outer edge of the clip.
Xserve Logic Board with Processor/Heatsink - 12 12. Remov e the battery insulator tab from the batter y holder on the replacement logic board. (Figure 14) Figure 14 Note: Replacing the logic board in the ser v er changes its Ethernet ID number . The new number is printed on an Ether net ID label pac kaged with the replacement logic board.
Xserve Logic Board with Processor/Heatsink - 13 Apple Computer , Inc. © 2002 Apple Computer , Inc. All rights reser v ed. This document is protected under U .S . Cop yright Law and Inter national T reaties, and no par t of this document ma y be reproduced in any f orm without written per mission from Apple.
デバイスApple Xserve 073-0711の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Apple Xserve 073-0711をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはApple Xserve 073-0711の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Apple Xserve 073-0711の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Apple Xserve 073-0711で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Apple Xserve 073-0711を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はApple Xserve 073-0711の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Apple Xserve 073-0711に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちApple Xserve 073-0711デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
