LochinvarメーカーCommercial Electric Water Heatersの使用説明書/サービス説明書
ページ先へ移動 of 16
1 INST ALLA TION AND SER VICE MANUAL SHP-I&S-02 COMMERCIAL ELECTRIC W A TER HEA TERS 52, 82, 1 19 Gallon, 9 kW - 54kW Input Models FIG . 1 Fr ont V iew V ertical Round Models Installation and serv ice must be performed by Qualified Serv ice P ersonnel Only .
2 W ARNING: CONTENTS W ar ranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Safety W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Checking the Equipment . . . . . . . . . . . . . . . .
3 CODES The equipment shall be installed in acco rdance with those installation regulations in forc e in the local area where the installation is to be made. These shall be carefully followed in all cases. A uthor ities having jurisdiction shall be consulted befor e installations are made.
4 CLEARANCES FROM COMBUSTIBLE CONSTRUCTION FIG. 2 Clearances from Co mbustible Construction T ABLE - A CLEARANCES FROM COMBUSTIBLE CONSTRUCTION: Right Side - 0" Rear - 0" Left Side - 0".
5 INLET AND OUTLET CONNECTIONS For ease of ser vice, install unions on the c old water inlet and hot water outlet of the water heater . The cold water inlet connection is located on the lo wer left front side of the water heater . A manual shutoff valve should be installed upstream on the cold wat er source as an isolation device.
6 ELECTRICAL CONNECTIONS All installation proc edures in volving electric power connection should only be performed by a trained, certified electricians. FIG. 4 Electric P ower Co nnections - Electr ical Control Pa n e l W ARNING: W A TER HEA TER IS EQUIPPED FOR OPERA TION ON ONE V OL T AGE ONL Y .
7 JACKET ASSEMBL Y Outer Jack et - The out er jacket assembly is c onst ructed from hea vy gauge steel. The ext er ior surface is specially prepared and phosphat e coated to allow application of a multiple coat enamel paint pr ocess. This coating process insures a long life from the jack et assembly .
8 A main power t er minal block is provided for field connection of the branch power supply to the electric water heater . All internal pow er circuits to the immersion heating elements are c onnected to the load side of the main terminal block.
9 The limit is reset by pushing the r ed reset button on the limit. Operation of the limit control usually indicates a major problem with the heating elements or temperature contr ol. Do not contin ue to push the reset m ultiple times. The problem causing the r eset to function must be found and corrected to insur e proper operation.
10 W ARNING: HAZARD OF ELECTRICAL SHOCK - Before opening the electrical access panel to adjust the thermostat or ser vicing the water heater , make sur e the electrical supply to the water heater is turned "OFF". Failure t o do this could result in death, serious bodily injur y or propert y damage.
11 W ARNING: SHOULD O VERHEA TING O CCUR OR THE TEMPERA TURE CONTROLS F AIL TO SHUT OFF , TURN OFF OR DISCONNECT THE ELECTRICAL SUPPL Y A T THE MAIN POWER DISCONNECT , EXTERN AL TO THE APPLIANCE. DANGER • W ater temperature over 125°F (51.7°C) can cause severe burns instantly or death from scald.
12 IMMERSION HEA TING ELEMENTS FIG. 14 Immersion H e ating Element W ARNING: HAZARD OF ELECTRICAL SHOCK - Before opening the access panel t o remove or service the immersion heating elements, make sur e the elect rical supply to the water heat er is turned "OFF".
13 NOTE: The cold water supply m ust be left in the open position when the water heater is in use. 5. Check the near by hot water faucet t o verify that air is exiting the tank as it fills with water . Allow wate r to run until a constant flo w is obtained at the faucet.
14 SHUTDOWN PROCEDURE 1. T urn off the main electr ical power t o the water heater . If the power disc onnect point is out of sig ht, lock it in the open ("OFF") position and tag to prev ent unexpected application of power . 2. T urn the valve in the water heat er's cold water supply to the closed or "OFF" position.
Scale accumulation in the bott om of the storage tank may be remo ved by turning off main power and draining the tank. Once all wate r is remo ved, the hand hole access can be remo ved. This w ill allow large ac cumulations of scale to be cleaned from the bottom of the tank.
Revision Notes: Revision 2 (ECO #C02870) reflects the addition of the scald char t on page 10. CP -5M-1/09-Printed in U.S.A. 16 7. Clean remaining gask et recess on eac h screw-in element flange. Do not reuse element gask ets. 8. Install a new gask et on each element.
デバイスLochinvar Commercial Electric Water Heatersの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lochinvar Commercial Electric Water Heatersをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLochinvar Commercial Electric Water Heatersの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lochinvar Commercial Electric Water Heatersの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lochinvar Commercial Electric Water Heatersで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lochinvar Commercial Electric Water Heatersを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLochinvar Commercial Electric Water Heatersの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lochinvar Commercial Electric Water Heatersに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLochinvar Commercial Electric Water Heatersデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
