Lowrance electronicメーカーLINK-8VHFの使用説明書/サービス説明書
ページ先へ移動 of 20
lowranc e.c om ENGLISH Link-8 VHF Installation Instruc tions.
Copyright © 2013 Navic o All rights reserved. Lowranc e® is a registered tr ademark of Navico No part of this manual may be copied, reproduced, r epublished, transmitted or distributed for any purpose, without prior written consent of L owrance Electronics.
Lowrance - Link -8 Installation Instruc tions 3 T able of Contents 1 Installation preparation ................................................................................ 6 1.1 Checklist.............................................................
MMSI and license information Y ou must obtain a user MMSI (Marine Mobile S ervice Identity) and enter it into your Link-8 in or der to use the DSC functions. Contact the appropriate authorities in your coun tr y . If you are unsure who to contact, consult your L owrance dealer .
RF Emissions notice This equipment complies with FC C radiation exposure limits set forth for an uncontrolled environ- ment. This device’ s antenna must be installed in accordance with provided inst.
Note: A VHF antenna is not provided b y Lowrance. C onsult your Lowr ance dealer for advice if necessary. 1 . 2 T ools needed for inst allation Y ou will need the following tools: • Po wer drill (or hand drill) and drill bits • Philips screwdriver • Spanner • Jig saw (for a rec essed installation).
2 VHF installation 2. 1 Locatio n requirements Please check these before doing an y cutting or drilling. Whichever installation method you choose , ensure that the chosen location: • Is at least 3’ (1 m) from the antenna • Allows easy connection to (at least) a 10 Amp fused 13.
2. 3. 1 Mounting bracket installation 1. Hold the supplied mounting bracket at the chosen location and use a soft pencil to mark the 4 screw hole positions onto the mounting surface. 2. Drill the 4 screw holes where marked. Drill completely thr ough the mounting surface.
2. 3.2 Recessed installat ion 1. T ape the supplied mounting template to the chosen location. Ensure that the template is smooth and taut. 2. Drill the 2 screw holes where marked. Drill completely thr ough the mounting surface. Note: If you are drilling into ber glass, use a small drill bit to drill pilot holes before drilling the screw holes.
2.4 Link - 8 dim ensions Lowrance - Link -8 Installation Instruc tions 10.
2.5 Handset m ic wall hanger 1. Hold the handset mic wall hanger at the chosen location and use a soft pencil to mark the 2 screw hole positions onto the mounting surface. 2. If the mounting sur face is: • non-metallic, use the 2 self-tapping screws and 2 plain washers t o attach the handset mic wall hanger to the mounting surface.
3 VHF electrical installation 3. 1 Connect the r adio Both NMEA 0183 and NMEA 2000 is supported by this radio. Use the GPS connector cable to connect NMEA 0183, or the N2K connector for NMEA 2000 connections. 1 VHF antenna A suitable radio antenna (not supplied) must be mounted and c onnected before you can operate the radio .
Pin / Socket Wir e color Function (NMEA 2000) 1 Green Can-D , Drain wire, Shield 2 Red Can-S, P ower , +12 V DC 3 Black Can-C, Ground 4 White Can-H, Data High 5 Blue Can-L, Data Lo w 3 GPS Connector a.
4 Hailer Horn Wir e color Function Details White (+) Connect to hailer speaker + Shield (-) Shield Connect to hailer speaker - Important: Do not shor t these 2 wires. Install the hailer horn in a forward-facing location on the boat because the hailer horn will transmit the FOG horn sounds and will ‘listen back’ when not transmitting.
3. 2 Wirin g diagra m - NME A 2000 Lowrance - Link -8 Installation Instruc tions 15.
External Speaker Hailer Speaker VHF Antenna 3.3 Wirin g diagram - External spe aker an d hailer Lowrance - Link -8 Installation Instruc tions 16.
3.4 Wi ring di agram - N MEA 01 83 conne ctio ns Link-8 VHF GPS Plotter + 12 VDC Fuse Switch Pow er 12 VDC only 1. Shield NMEA0183 In 4800 DSC Information NMEA0183 Out GPS Position RS422 38,400 AIS Information 2. Orange 3. White 4. Green 5.
4 Setup your radio - Y our user MMSI CAUTION Y ou can’ t make any DSC transmissions until you ’ve obtained a user MMSI and entered it into y our radio. Y ou must enter your User MMSI bef ore the DSC functions of this radio will work. See the Setup section in the Link-8 User Guide for full setup details.
.
1177 *988-10249-002*.
デバイスLowrance electronic LINK-8VHFの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lowrance electronic LINK-8VHFをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLowrance electronic LINK-8VHFの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lowrance electronic LINK-8VHFの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lowrance electronic LINK-8VHFで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lowrance electronic LINK-8VHFを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLowrance electronic LINK-8VHFの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lowrance electronic LINK-8VHFに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLowrance electronic LINK-8VHFデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。