Lowrance electronicメーカーX50 DSの使用説明書/サービス説明書
ページ先へ移動 of 56
Pub. 988-0151-431 www.lowrance.com Fish-Finding Sonar Installation and Operation Instructions.
Copyright © 2006 Lowrance El ectronics, Inc. All rights reserved. No part of this manual may be copied, reprod uced, republished, transmitted or distributed for any purpose, with out prior written consent of Lowrance Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited .
i Table of Contents Introduction ....................................................................................... 1 Capabilities and Specif ications: X50 DS ............................................ 1 How Sonar Works ........................
ii Deep Ala rm ......................................................................................... 40 Battery Alarm..................................................................................... 40 Noise Rejection and ASP .............
1 Introduction Thank you for buying an Lowrance sonar! Your unit is a high-quality sonar designed for both professi onal and novice fishermen. All Lowrance sonars have an automatic mode that finds and displays the bottom, fish, underwater structure and more – right out of the box.
2 Transmitter: .................... 1,500 watts pe ak-to-peak power (typical); 188 watts RMS power (typical). Sonar sounding depth capability: ............ 1, 000 feet (305 meters). Act ual capability de- pends on transducer configuration and in- stallation, bottom composition and water con- ditions.
3 The receiver amplifies this return si gnal, or echo, and sends it to the display, where an image of the object appears on the scrolling sonar chart. The sonar's microprocessor calculates the time lapse between the transmitted signal and echo return to determine the distance to the object.
4 3. Determine the location of your battery or other power connection, along with the power cable route. 4. Install the transducer and route the transducer cable to the sonar unit. 5. Route the power cable from the unit's location to an appropriate power source and connect it there.
5 Single-frequency tra nsom installations Tools include: two adjustable wrench es, drill, #29 (0.136") drill bit, flat- head screwdriver (for mounting screws and their pilot holes). Supplies: none. Single-frequency trolling motor ins tallations Tools: two adjustable wrenches, flat-head screwdriver.
6 5. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from engine wi ring, bilge pumps and aerators can be displayed on the sonar's screen. Use caution when routing the transducer cable around these wires.
7 If you cruise or fish around lots of structure and cover, your transducer may be frequently kicking up from ob ject strikes. If you wish, you may move the transducer a little higher for more protection. There are two extremes you should avoid. Never let the edge of the mounting bracket extend below the bottom of the hull.
8 Place each ratchet into the bracket with the letter "A" aligned with the dot stamped into the metal bracket. This position sets the transducer's coarse angle adjustment for a 14 ° transom. Most outboard and stern-drive transoms have a 14 ° angle.
9 3. Assembling the transducer. Once you determine the correct posi- tion for the ratchets, assemble the transducer as shown in the following figure. Don't tighten the lock nut at this time. Assemble transducer and bracket. 4. Drilling mounting holes.
10 Position transducer mount on transom and mark mounting holes. Side view shown at left and seen from above at right. 5. Attaching transducer to transom. Remove the transducer from the bracket and re-assemble it with the cable passing through the bracket over the bolt as shown in the following figures.
11 Align transducer centerline with hull bottom and attach to transom. 6. Route the transducer cable through or over the transom to the sonar unit. Make sure you leave some slack in the cable at the transducer. If possible, route the transducer cable away from other wiring.
12 Trolling Motor Bracket Installation 1. Attach the optional TMB-S bracket to the transducer as shown in the following figure, using the hardware supplied with the transducer. (Note: The internal tooth washer is supplied with the TMB-S.) Attach motor mounting bracket to transducer.
13 Transducer Orientation and Fish Arches If you do not get good fish arches on your display, it could be because the transducer is not parallel with the ground when the boat is at rest in the water or at slow trolling speeds. Transducer angles and their effects on fish arches.
14 ers. The sonar signal must pass th rough solid fiberglass. A successful transducer installation can be made on hulls with flotation materials (such as plywood, balsa wood or foam) between layers of fiberglass if the material is removed from the chosen area.
15 Testing Determines Best Location Ideally, the shoot-thru transducer shou ld be installed as close to the transom as possible, close to the ce nterline. This will give you the best performance during high speed maneuvers. 1. Anchor the boat in about 30 feet of water.
16 hull. This is especially true if you have to turn sensitivity all the way up to get a decent bottom signal. 4. Most people can get good results by following steps 1 through 3, so this step is optional .
17 2. The epoxy consists of the epoxy itself and a hardener. Remove the two compounds from the package and place them on the paper plate. Thoroughly stir the two compounds together until the mixture has a uniform color and consistency. Do not mix too fast or bubbles will form in the epoxy.
18 power cable when the unit is not in use. When you are not using the unit, you should always shut off power to the power cable, es- pecially when the power cable is disconnected from the unit. Power connections for the X50 DS sonar unit (direct battery connection shown).
19 Bracket Installation Recommended tools for this job include: drill, 1" (25.4 mm) drill bit, screwdriver. Required supplies for this job include: high quality, ma- rine grade above- or below-waterline caulking compound, three #10 stainless steel screws.
20 After drilling the hole, pass the connectors up through the hole from und er t he d ash . If you wish, you can fill in the hole around the cable with a good marine caulking compound. (Some marine dealers stock cable hole covers to conceal the opening.
21 Mount the sonar: slide the unit onto the bracket from above. Adjust viewing angle: use one hand to press and release the spring- loaded ratchets while you move the unit with the other hand. Portable Sonar Installation Like many Lowrance products, the X 50 DS sonar is capable of portable operation.
22 To use a portable power pack, you install the batteries and then attach the sonar unit to the power pack's bracket. Plug in the power/transducer cable and you're ready to fish. The PPP-12 has a quick-release mounting bracket built into the case.
23 To mount the sonar, slide the unit on to the bracket from above (left). To adjust the view, press and release spring-loaded ratchets while tilt- ing the unit (right). To adjust the viewing angle, pinch the quick-release mount's ratchets with one hand, then tilt the unit with your other hand.
24 Make sure there is one washer on each side of the transducer, inside the bracket. Slide the other washer over th e end of the bolt and screw on the nut. Screw the suction cup onto the bracket using the supplied screw and flat washer. Tie the nylon cord through the hole in the top of the bracket.
25 Portable transducer installed on boat transom. Portable Transducer Storage There is room inside the power pa ck for the portable transducer. When you're finished fishing, tilt the so nar down to the storage position. Open the case and lay it flat.
26 Notes.
27 Operation Keyboard Basics The unit sounds a tone when you pre ss any key. This tells you the unit has accepted a command. Numbers in the figure correspond to key ex- planations below: Lowrance X50 DS. 1. PWR/CLEAR In this manual, the Power/Clear key is referred to as PWR .
28 cases, the text uses the word MENU . Usually, when the instructions say MENU , you can press the MENU UP key for consistency. The MENU UP key cycles forward through the menus. The MENU DOWN key moves backward through the menus. To check out the menus, re- peatedly press a MENU key to scroll through them.
29 Display The lights will flash for about 10 seconds when the unit is turned on. The backlight menu will appear on the screen. Use the A RROW keys to turn the backlight on or off. Press PWR to clear the menu from the screen. The unit will show the Full Chart Page or mode.
30 Full Chart page, showing digital depth (above) and temp (below). The Fish I.D. feature is turned off. Depth Range When turned on, the unit automatically adjusts the depth range ac- cording to water conditions. When in auto range mode, it always keeps the bottom displayed in the lower portion of the screen.
31 Zoom The zoom feature enlarges all images on the screen by doubling the size of the echoes (a 2X zoom). For example, if the current auto depth range is 0 to 60 feet, Zoom will show an enlarged view of the water column from 30 feet to 60 feet, always keeping the bottom in view.
32 Zoom Range menu with the 40-80 foot zoom selected. You can select from these zoom size ranges: 0-10, 5-15, 10-20, 15-30, 20- 40, 30-60, 40-80, 50-100, 75-150, 100-200, 150-300, 200-400, 300-600, 400-800, 500-1000, 750-1500 and 1000-2000. Sensitivity Sensitivity adjusts the way echoes will be displayed on the screen.
33 To adjust sensitivity in Auto Mode: Repeatedly press MENU until the S ENSITIVITY menu appears. Make sure sen- sitivity is set to Auto, then press MENU UP to access the sensitivity scroll bar. P r e s s ↑ to increase the sensitivity, ↓ to decrease it.
34 Grayline ® Grayline lets you distinguish between strong and weak echoes. It al- lows you to tell the difference between a hard and soft bottom. For ex- ample, a soft, muddy or weedy bottom returns a weaker signal which is shown with a narrow line or no gray line at all.
35 A small amount of Grayline indicates a soft bottom (left), probably sand or mud. More Grayline indicates a harder, rocky bottom (right). Press ↑ to increase Grayline, ↓ to decrease it. Echoes scrolling on the screen will show the effects of the Grayline adjustment.
36 sonar signal cone, the image appears on the screen as a long line in- stead of a fish arch. Reducing the chart speed may result in a shorter line that more closely resemb les a regular fish return. To adjust Chart Speed, repeatedly press MENU until the C HART S PEED scroll bar appears.
37 The Fish I.D. feature displays symbol s on the screen in place of the ac- tual fish echoes. There are three symbol sizes: small, medium and large. These show the relative size between targets. In other words, it displays a small fish symbol when it thinks a target is a small fish, a medium fish symbol on a larger target and so forth.
38 Fish I.D. can also be useful when you want to screen out som e of the so- nar detail gathered by your unit. For example, it can help cut through the clutter of suspended bubbles caused by wave action or boat wakes. T o t u r n F i s h I . D . o f f , r e p e a t e d l y p r e s s MENU until the F ISH ID menu ap- pears.
39 Fish Alarm menu. Depth Alarms The depth alarms are triggered only by the bottom signal. No other echoes will activate these alarms. The depth alarms consist of a shal- low and a deep alarm. The shallow alarm sounds an alarm tone when the bottom goes shallower than the alarm's setting.
40 any of the previously entered numbers, press MENU UP . Press PWR to return to the Shallow Alarm menu. Use ↑ to select O N , which will turn on the alarm, then press PWR to clear the menu. When the bottom depth becomes more shallow than the alarm’s setting, an alarm will sound and a message will appear on the screen.
41 Battery Alarm menu (left). Low Battery Alarm Value (right). Press the ↓ to S ET V AL UE . The Low Battery Alarm Value dialog box will appear. Input a voltage value between 7 and 18 volts. Use the ↑ ↓ keys to enter the first number in the dialog box, then press MENU DOWN to move to the next digit.
42 Noise Rejection menu. The ASP noise rejection feature is especially useful because, typically, it lets you operate the boat at all speeds without adjusting the sensi- tivity or other controls. The ASP feature has three settings — Off, Low and High.
43 Depth Display Depth may be displayed on the screen in a small, medium or large size or can be turned off completely. To display Depth: Repeatedly press MENU until the D EPTH menu appears. Use ↑ ↓ to select the size of the depth display. Press PWR to clear the menu.
44 Voltage The Voltage menu allows you to display battery voltage on the screen in a small or medium size or can be turned off completely. To display battery voltage: Repeatedly press MENU until the V OLTAGE menu appears. Use ↑ ↓ to se- lect the size of the voltage display.
45 Simulator menu (left). Languages menu (right). To use the simulator, repeatedly press MENU until the S IMULATOR menu appears. Press ↑ to turn it on and press PWR to clear the menu. Repeat the steps above to turn it off. The simulator autom atically will be turned off when you power off the unit.
46 Troubleshooting If your unit is not working, or if yo u need technical help, please use the following troubleshooting section be fore contacting the factory cus- tomer service department. It may save you the trouble of returning your unit for repair.
47 3. The water may be deeper than the sonar's ability to find the bottom. If the sonar can't find the bottom signal while it's in the automatic mode, the digital sonar display will flash continuously. It may change the range to limits far greater than the water you are in.
48 vere cases, it can completely cover the screen with black dots, or cause the unit operate erratically, or not at all. To eliminate or minimize the effects of electrical noise, first try to de- termine the cause. With the boat at rest in the water, the first thing you should do is turn all electrical equipm ent on the boat off.
49 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRANCE ELECTRONICS, a division of LEI, the manu- facturer of this prod uct. "You" or "your" refers to the first p erson who purchases this product as a consumer item f or personal, family, or household use.
50 How to Obtain Service… …in the USA: We back your investment in quality pr oducts with quick, expert service and genuine Lowrance replacement parts. If you're in the United States and you have technical, return or repair questions, please con- tact the Factory Customer Service Department.
Accessory Ordering Information for all countries To order Lowrance GPS accessories such as computer cables or MMC cards, please contact: 1) Your local marine de aler or consumer electron ics store. Most quality dealers that han dle marine electronic equipment or other consumer electronics should be a ble to assist you with thes e items.
Visit our web site: Lowrance Pub. 988-0151-431 © Copyright 2006 All Rights Reserved Printed in USA 032106 Lowrance Electronics, Inc..
デバイスLowrance electronic X50 DSの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lowrance electronic X50 DSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLowrance electronic X50 DSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lowrance electronic X50 DSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lowrance electronic X50 DSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lowrance electronic X50 DSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLowrance electronic X50 DSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lowrance electronic X50 DSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLowrance electronic X50 DSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。