AbitメーカーIS85の使用説明書/サービス説明書
ページ先へ移動 of 32
Introduction Hardware Setup BIOS Setup Driver & Utility Appendix IS-85 Motherboard Intel Pentium 4/Celeron/Celeron D Socket 775 Installation Instruction.
Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual.
Introduction Contents 1. Introduction ..................................................................... 1-1 Hardware Setup BIOS Setup Driver & Utility Appendix 1.1 Features & Specifications .................................................
3. BIOS Setup ....................................................................... 3-1 4. Driver & Utility ................................................................. 4-1 5. Appendix .......................................................
Introduction 1. Introduction 1.1 Features & Specifications CPU • LGA775 Socket for Intel Pentium 4/Celeron/Celeron D Processor with 800/533MHz FSB • Supports Intel Hyper-Threading Technology C.
• 1x Parallel port • 1x VGA port • 4x USB 2.0 ports • 1x RJ-45 LAN port • 1x Audio connector (Line-in, Line-out, MIC-in) Miscellaneous • mATX form factor (244mm x 244mm) ※ Specifications and information contain ed herein are subject to change without notice.
Introduction 1.2 Motherboard Layout IS-85 1-3.
1-4 IS-85.
Hardware Setup IS-85 2-1 2. Hardware Setup In this chapter we will elaborate all the information you need upon installing this motherboard to your computer system. ※ Always power off the computer and unplug the AC power cord before adding or removing any peripheral or component.
To install this motherboard: 1. Locate all the screw holes on the motherboard and the chassis base. 2. Place all the studs or spacers needed on the chassis base and have them tightened. 3. Face the motherboard’s I/O ports toward the chassis’s rear panel.
Hardware Setup IS-85 2-3 2.3.1 CMOS Memory Clearing Header and Backup Battery The time to clear the CMOS memory occurs when (a) the CMOS data becomes corrupted, (b) you forgot the supervisor or user password preset in the BIOS menu, (c) you are unable to boot-up the system because the CPU ratio/clock was incorrectly set in the BIOS menu.
CMOS Backup Battery: An onboard battery saves the CMOS memory to keep the BIOS information stays on even after disconnected your system with power source.
Hardware Setup IS-85 2-5 2.4 Connecting Chassis Components 2.4.1 ATX Power Connectors These connectors provide the connection from an ATX power supply. As the plugs from the power supply fit in only one orientation, find the correct one and push firmly down into these connectors.
2.4.3 Front Panel Switches & Indicators Headers This header is used for connecting switches and LED indicators on the chassis front panel. Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below stands for positive polarity for the LED conn ection.
Hardware Setup IS-85 2-7 2.5 Installing Hardware ※ DO NOT scratch the motherboard when installing hardware. An accidentally scratch of a tiny surface-mount component may seriously damage the motherboard. ※ In order to protect the contact pins, please pay attention to these notices: 1.
4. Visually inspect if the CPU is seated well into the socket. The alignment key must be located in the notch of package. 5. Use your left hand to hold the load plate, and use your right thumb to peel the cap off. ※ The cap plays an important role in protecting contact pins.
Hardware Setup IS-85 2-9 8. Place the heatsink and fan assembly onto the socket. Align the four fasteners toward the four mounting holes on the motherboard. 9. Press each of the four fasteners down into the mounting holes. Rotate the fastener clock-wise to lock the heatsink and fan assembly into position.
2.5.2 DDR Memory Slots This motherboard provides 2x 184-pin un-buffered DDR SDRAM slots for the installation of dual channel DDR400 memory modules maximum up to 2GB capacity. ※ To reach the optimum performance in dual-channel configur ations, install DDR DIMM pairs at the same density, DRAM technology and bus width for both slots.
Hardware Setup IS-85 2-11 2.5.3 Floppy and IDE Disk Drive Connectors The FDD connector connects up to two floppy dr ives with a 34-wire, 2-connector floppy cable. Connect the single end at the longer length of ribbon cable to the FDD on the board, the two connectors on the other end to the floppy disk drives connector.
2.5.4 Serial ATA Connectors Each SATA connector serves as one single channel to connect one SATA device by a thin SATA cable. To connect SATA device: 1. A ttach either end of the si g nal cable to the SATA connector on motherboard. Attach the other end to SATA device.
Hardware Setup IS-85 2-13 2.5.5 Accelerated Graphics Port Slot This slot supports an optional AGP graphics card up to AGP 8X mode. ※ This motherboard does not support 3.3V AGP cards. Use only 1.5V or 0.8V AGP cards. 2.5.6 PCI Add-on Slots These slots provide the connection of add-on cards that comply with PCI specifications.
2.6 Connecting Optional Devices 2.6.1 Additional USB 2.0 Port Headers Besides the 4x USB 2.0 ports located at rear I/ O part, this motherboard also features 2x more USB 2.0 headers onboard. Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis.
Hardware Setup IS-85 2-15 2.6.3 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. • To use the audio connector at front panel, remove all the jumpers on this header, and then connect to front panel by the extension cable provided with the chassis.
2.7 Connecting I/O Devices • Mouse: Connects to PS/2 mouse. • Keyboard: Connects to PS/2 keyboard. • LPT1: Connects to printer or other devices that support this communication protocol. • COM1: Connects to external modem, mouse or other devices that support this communication protocol.
BIOS Setup IS-85 3-1 3. BIOS Setup This motherboard provides a programmable EEPRO M that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals.
3-2 IS-85.
Driver & Utility IS-85 4-1 4. Driver & Utility The “Driver & Utility CD” that came packed with this motherboard contains drivers, utilities and software applications required for its basic and advanced features. Place the “Driver & Utility CD” into the CD-ROM dr ive in your system.
4-2 IS-85.
Appendix IS-85 5-1 5. Appendix 5.1 Troubleshooting (How to Get Technical Support?) 5.1.1 Q & A Q: Do I need to clear the CMOS before I us e a new motherboard to assemble my new computer system? A: Yes, we highly recommend that you clear the C MOS before installing a new motherboard.
Upgrade the motherboard’s latest BIOS version. Upgrade the add-on device’s latest driver version. Check if there is any conflict in the “Control Panel/System Properties”.
Appendix IS-85 5-3 5.1.2 Technical Support Form Country: First name: Last Name: Subject: Motherboard: BIOS Version: CPU: Memory brand: Memory size: Memory configuration: Graphics card: Graphics driver.
Rev. 1.00 ABIT Computer Corporation http://www.abit.com.tw.
デバイスAbit IS85の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Abit IS85をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAbit IS85の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Abit IS85の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Abit IS85で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Abit IS85を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAbit IS85の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Abit IS85に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAbit IS85デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
