Mackieメーカー1220Iの使用説明書/サービス説明書
ページ先へ移動 of 41
OWNER'S MANUAL 12-Channel P remium Analog Mix er with F ireWire dB 30 20 10 40 50 5 5 U 60 10 O O 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3 / 4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3 / 4 10 dB 3.
2 Onyx 1220i 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with a dr y cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
Owner ' s Manual 3 Part No. SW0722 Rev . B 02/2010 ©2010 LOUD T echnologies Inc. All Rights Reserved. Loosely based on a dream sequence in which the technical writer is given keys to a sports car of his choice, unlimited gas, and closed roads. The dream suddenly ends and reality kicks in.
4 Onyx 1220i Introduction Thank you for choosing a Mackie Onyx 1220i professional compact mixer . The Onyx-i series of mixers offer built-in Fir eWir e, along with the newest features and latest technologies for live sound r einforcement and analog or digital studio r ecording, all in a durable, road-worthy package.
Owner ' s Manual 5 Ho w T o Use This Manual The fi rst pages after the table of contents are the hookup diagrams. These show typical setups for fun times with your mixer .
6 Onyx 1220i Contents IMPOR T ANT SAFETY INSTRUCTIONS ........................ 2 QUICK ST ART .......................................................... 3 INTRODUCTION ...................................................... 4 HOOKUP DIAGRAMS...........
Owner ' s Manual 7 dB 30 20 10 40 50 5 5 U 60 10 O O 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3/4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3/4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3/4 10 dB 30 20 1.
8 Onyx 1220i This diagram shows an electric guitar connected to the channel 1 line input via an amplifi er modeller , a bass guitar connected directly to channel 2 (hi-z switch in), microphones conne.
Owner ' s Manual 9 dB 30 20 10 40 50 5 5 U 60 10 O O 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3/4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3/4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3/4 10 dB 30 20 1.
10 Onyx 1220i P ost-Production System This diagram shows a voice-over microphone connected to the channel 1 mic input, a video deck's audio outputs connected to channels 5/6, with its audio inputs receiving the main mix from the 1/4" main outputs.
Owner ' s Manual 11 Onyx 1220i Features Rear Panel 1. POWER CONNECTION This is a standard 3-prong IEC power connector . Connect the detachable linecord (included in the box with your mixer) to the power r eceptacle, and plug the other end of the linecord into an AC outlet.
12 Onyx 1220i as well as to solo, and add to aux send 1 and 2. This is routed using the FW/line input selector [23] on channels 11 and 12. This is useful for live performances, wher e those 2 channels.
Owner ' s Manual 13 Professional ribbon, dynamic, and condenser mics all sound excellent through these inputs. The mic inputs will handle any kind of mic level you can toss at them, without overloading. Microphone-level signals ar e passed through the mixer's splendid microphone pr eamplifi ers to become line-level signals.
14 Onyx 1220i T o connect unbalanced lines to these inputs, use a 1⁄4" mono (TS) phone plug, wir ed as follows: T ip = Positive (+ or hot) Sleeve = Shield or ground The line-level inputs of channels 1 and 2 can also accept instrument-level signals if the hi-z switches [18] ar e pressed in.
Owner ' s Manual 15 15. T APE INPUTS These ster eo unbalanced RCA inputs allow you to play a tape, CD player , iPod ® dock, or other line-level source. The tape in jacks accept an unbalanced signal using standard hi-fi hookup cables. Push in the tape button [36] to route the tape input to the control room and phones outputs [12, 17].
16 Onyx 1220i Channel Controls The vertical channel strips look very similar , and have only a few differ ences between them. Each channel works independently , and just controls the signals plugged into the inputs dir ectly above it.
Owner ' s Manual 17 18. HI-Z SWITCH (Ch. 1 and 2 only) Engage this switch if you want to connect guitars dir ectly to the 1/4" line inputs of channels 1 or 2. W ithout this switch, you need to use a DI box fi rst, befor e connecting guitars.
18 Onyx 1220i 22. SEND FIREWIRE PRE/POST Each channel of the mixer can send a Fir eWir e output to your computer or DA W . The Fir eW ire output from each channel can be tapped befor e (pre) or after (post) the channel EQ. (The output is always pr e-fader .
Owner ' s Manual 19 24. HIGH EQ The high EQ provides up to 15 dB of boost or cut above 12 kHz, and it is also fl at (no boost or cut) at the detent. Use it to add sizzle to cymbals, an overall sense of transpar ency , or an edge to keyboards, vocals, guitar and bacon frying.
20 Onyx 1220i 29. AUX SEND 1 and 2 These controls allow you to set up two independent mixes, typically for running stage monitors or external effects processors. The controls ar e off when turned fully down, deliver unity gain at the center , and can provide up to 15 dB of gain turned fully up.
Owner ' s Manual 21 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3 / 4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3 / 4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3 / 4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3.
22 Onyx 1220i T ape is the stereo signal coming in from the tape in [15] RCA jacks. Fir eWir e is a 2-track feed coming in through the Fir eWir e [3] connection from your computer . Alt 3-4 is the additional stereo mix bus formed when any channel is muted with the mute/alt 3-4 switch [31].
Owner ' s Manual 23 39. PHONES Knob This controls the volume at the phones output, from off to maximum gain. W ARNING: The headphone amp is loud, and can cause permanent hearing damage. Even intermediate levels may be painfully loud with some headphones.
24 Onyx 1220i Aux Master This section includes the aux sends and the aux r eturns. Aux sends tap signals off the channels, via the aux knobs [29], mix these signals from each channel together , then sends them out the aux send jacks [6] and Fir eWir e outputs 11 and 12.
Owner ' s Manual 25 46. POWER LED This gr een LED will turn on when the mixer is turned on, as a r eminder of how on it really is. If it is not on, then it is off, and the mixer becomes a rather nice weight for keeping your morning newspaper from blowing away in the wind.
26 Onyx 1220i The aux 1-2 switch routes the talkback signal to the aux send 1 and 2 outputs [6]. Use this to communicate with the musicians through their stage monitors when you ar e setting up a live performance. It is fi ne to have both destination switches pushed in at the same time, so the talkback signal will be routed to both destinations.
Owner ' s Manual 27 Appendix A: Ser vice Information If you think your mixer has a problem, please check out the following troubleshooting tips and do your best to confi rm the problem.
28 Onyx 1220i “XLR” Connectors Mackie mixers use 3-pin female “XLR” connectors on all microphone inputs, with pin 1 wir ed to the grounded (earthed) shield, pin 2 wir ed to the “high” (”hot” or positive polarity) side of the audio signal and pin 3 wir ed to the “low” (“cold” or negative polarity) side of the signal.
Owner ' s Manual 29 TRS Send/Receive Insert Jacks Mackie’ s single-jack inserts are the thr ee- conductor , TRS 1⁄4" phone type. They ar e unbalanced, but have both the mixer output (send) and the mixer input (r eturn) signals in one connector .
30 Onyx 1220i Appendix C: T echnical Information Specifi cations Noise Char acteristics: Equivalent Input Noise (EIN), mic input at insert, 150 Ω source impedance, 20 to 20 kHz: 60 dB (max) gain: -127 dBu 40 dB gain: -126.5 dBu Equivalent Input Noise (EIN), mic input at insert, 50 Ω source impedance, A-weighted: 60 dB (max) gain: -130.
Owner ' s Manual 31 Fir eWir e Sample Rates A vailable: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz Buffer Size: 32 (44.1 kHz and 48 kHz only), 64, 128, 256, 512, 1024, 2048 samples Resolution: 24-bit Met.
32 Onyx 1220i L R A ux 1 (p ost) Aux 2 (pos t) Solo(PFL) SoloLogi c Main L/3 R/4 Alt Aux 1 (pre) Aux 2 (pre) L R Aux 1 (post) Aux 2 (pos t) Solo(PFL) SoloLogi c Main L/3 R/4 Alt Aux 1 (pre) Aux 2 (pre.
Owner ' s Manual 33 The optional Rack Ear Kit allows the Onyx 1220i mixer to be mounted in a standard 19” rack. It will be out of harm’ s way and the band may continue tearin’ it up without fearing any consequences. The mixer takes up ten rack spaces.
34 Onyx 1220i Appendix E: FireWire The mixer comes with a CD containing the PC driver softwar e needed to use your mixer's internal FireW ire interface with W indows XP or Windows Vista. Mac OS X contains built-in drivers, so no softwar e installation is r equired.
Owner ' s Manual 35 6. Select "Install," and the driver softwar e will be installed. 7. The following message confi rms that the driver softwar e has been successfully installed.
36 Onyx 1220i 7. Select the “Next” command and the driver softwar e will begin installing. 8. When W indows presents you with a warning about the softwar e not having passed Windows testing, select “Continue Anyway .” 9. Repeat steps 3-8 to allow a second driver to be installed.
Owner ' s Manual 37 USING THE ONYX 1220i WITH A MAC The Onyx 1220i works with Mac OS 10.4.11 and higher . This OS includes the Apple Fir eWir e 2.0 driver . The Onyx 1220i will only work with the 2.0 driver , so if you have an OS befor e 10.4.11, you will need to check your system for updates from the nice folks at Apple.
38 Onyx 1220i Appendix F: Modifi cations The following modifi cations can be carried out on the Onyx 1220i by an authorized service center . Authorized service centers may be found online at: www .
Owner ' s Manual 39 dB 30 20 10 40 50 5 5 U 60 10 O O 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3 / 4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3 / 4 10 dB 30 20 10 40 50 5 5 U 60 O O AL T 3 / 4 10 dB .
40 Onyx 1220i Onyx 1220i Limited W arranty Please keep your sales receipt in a safe place. This Limited Product W arranty (“Product W arranty”) is provided by LOUD T echnologies Inc. (“LOUD”) and is applicable to products purchased in the United States or Canada through a LOUD-authorized reseller or dealer .
16220 W ood-Red Road NE • W oodinville, W A 98072 • USA United States and Canada: 800.898.3211 Europe, Asia, Centr al and South America: 425.487 .4333 Middle East and Africa: 31.20.654.4000 F ax: 425.487 .4337 • www .mackie.com E -mail: sales@mackie.
デバイスMackie 1220Iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Mackie 1220Iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMackie 1220Iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mackie 1220Iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mackie 1220Iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mackie 1220Iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMackie 1220Iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mackie 1220Iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMackie 1220Iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
