Macsense ConnectivityメーカーDigital Wattmeter DWM-4の使用説明書/サービス説明書
ページ先へ移動 of 12
- 1 - Welcome : Thank you for your purchase of the DWM-4 Digital Wattmeter. The DWM-4 represents an advancement in technology that has never before been available in RF power measurement.
- 2 - in the assembly instructions to assist the builder. These can be used for parts identification and PC board placement. Assembly: You will first install (locate, place, and solder in place) the parts on the DWM-4 Main PC board. Use the silk screen layout in the back of this manual to assist in locating where parts are to be installed.
- 3 - ___ Install the socket for U1. Note the orientation of the socket. The flattened corner goes in the upper left, toward the 14-pin DIP socket for U3. Do not install U1 (the 68HC11) until later. ___ Install the 8 MHz crystal. ___ Install the electrolytic capacitor, C2, 10uf radial.
- 4 - ___ Install the LCD Module in the chassis. Use the 4 black flat head screws, the two #4 nylon washers and four nuts. Use the washers on the Status/SWR side of the chassis. Do not over tighten the mounting screws. ___ Install the SPST toggle switch (SW1) in the chassis in the Power On position.
- 5 - You are now ready to mount the DWM PC board in the chassis. ___ Install the DWM-4 PC board in the chassis using four screws, nylon spacers, washers and nuts. Do not drill out the holes in the PC board ___ Install U1 (the 68HC11) by carefully pressing it into place in its socket.
- 6 - ___ Install the .01uf monolithic capacitors, C1 and C2. ___ Install 1/8" ste reo jack. ___ Unwrap the enclosure. Install the SO-239 connectors. Put one #4 screw in hole and place two nuts on the screw. Repeat with the other three screws. Do not tighten them at this time.
- 7 - HF/QRP Remote Sensor Assembly Instructions ___ Wind T1 with 10 turns using the red and gr een #28 gauge wire. T1 is the small, black toroid just under one half inch in diameter. See picture below and wind this in bifiliar fashion by using two lengths of wire and winding them at the same time.
- 8 - ___ Install C4, 3.5-13 pf trimmer capacitor. Note that C4 has two pins that are common (connected). They should line up with the two holes in the PC board that are connected together with a trace on the bottom. ___ Install T1. It lies flat against the PC board and the #18 wire will pass through the center (you will install this later).
- 9 - Installation: The DWM-4 operates from an 11 to 15 volt DC power source. The current requirement is about 75 mA. Be sure to use a power supply or power adapter that meets these requirements. The coaxial DC jack on the back of the display unit will accept a plug with an OD of 5.
- 10 - menu offers information about each of the four sensor inputs. Some items are common across different menus. There are two basic wattmeter modes: setup and operate.
- 11 - At a minimum, a 100 W HF radio and good 50ohm dummy load can be used to calibrate the HF sensor and display unit. Even if you know how much power your radio emits, consider using an additional wattmeter of known accuracy to assist you during the calibration process.
- 12 - was installed correctly. Make sure U3 is installed correctly. Check D1 for polarity. Check the SIP resistor (RP1) for proper orientation. No Display: Make sure the 14-pin ribbon cable is installed and oriented properly. Be sure the nylon washers are in place on the two nuts closest to the outside.
デバイスMacsense Connectivity Digital Wattmeter DWM-4の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Macsense Connectivity Digital Wattmeter DWM-4をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMacsense Connectivity Digital Wattmeter DWM-4の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Macsense Connectivity Digital Wattmeter DWM-4の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Macsense Connectivity Digital Wattmeter DWM-4で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Macsense Connectivity Digital Wattmeter DWM-4を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMacsense Connectivity Digital Wattmeter DWM-4の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Macsense Connectivity Digital Wattmeter DWM-4に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMacsense Connectivity Digital Wattmeter DWM-4デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
